geemarc Amplicall 6 Wireless Door Smart Bulb User Guide
- June 4, 2024
- geemarc
Table of Contents
USER GUIDE
Note: For lamps with a weight significantly higher than that of the lamps
for which they are a replacement, attention should be drawn to the fact that
the increased weight may reduce the mechanical stability of certain luminaires
and lamp holders and may impair contact making and lamp retention.
!!! Please refer to our website: www.geemarc.com for an up-to-date user
guide, as there may be important updates and changes you need to be made aware
of !!!
Introduction
Congratulations on purchasing your Geemarc AMPLICALL6.
The Bulb unit (The AMPLICALL6) receives a transmitted signal from any number
of AMPLICALL transmitters. For example, the AMPLICALL1, 2,3, 30 & 40 and extra
AC6 LR.
Unpacking the AMPLICALL6
When unpacking the AMPLICALL6, you will find the following in the box:
- 1 AMPLICALL6 Unit
- 1 master remote with battery
- 1 user guide.
General Description
Rated current: 0.022A
ta : 35 ℃
Mounting
- Turn off the power of your house light fitting
- Remove the Bulb
- Place the AMPLICALL6 Bulb
- Turn on the power
- Now you can use the remote to turn on your light.
Pairing
Once power is connected (every time AC is connected), Green LED will light for
10 seconds. This means the LED bulb is in pairing mode.
Pair with AC1, 2, 30, 40 (option)
If the LED bulb is under pairing mode, then press the AC1 (AC2, AC30-40 and
smoke alarm, etc.) to pair with the LED device.
If the 1st AC1 is paired with the bulb, the bulb’s White LED will flash once:
W – .
If the 2d AC1 is paired with the bulb, the bulb’s White LED will flash twice:
W – W.
If the 3rd AC1 is paired with the bulb, the bulb’s White LED will flash three
times: W – W – W.
If the 4th AC1 is paired with the bulb, the bulb’s White LED will flash four
times: W – W – W – W.
Remarks:
- AC6 is able to pair with 4 x AC6 LR. 4x extra devices e.g. AC1, 2, 3, 4, and 10x smoke alarms.
- If the LED bulb is under pairing mode, then press the Smoke alarm button, if the smoke alarm is paired with the bulb, the bulb’s White LED will flash once.
Pair with AC6 LR Remote Dim/Highlight/OFF switch
AC6 LR (Master Dim / Highlight / OFF) control is already pre-paired in the
factory.
User does not need to do the pairing procedure.
In case the user wants to have an extra AC6 LR to control the light bulb Dim /
Highlight / OFF, then one can pair the extra AC6 LR with the LED bulb. Just
follow the above pairing procedure.
Remarks:
- Geemarc LED bulb is able to pair with a maximum of 4 x CallHear extra AC1 remote devices plus 4 AC6 LR remotes and 10 x Smoke alarms. So a total of 18*remote devices can be paired (4+4+10).
- If more than 4 x extra remote device ACs are paired with the LED, then the LED will be based on “First IN First Out”, the 1st paired device will be removed from the bulb.
- If the AC failure duration is shorter than 1.0 seconds, the bulb will not enter pairing mode.
AC6 LR Remote Dim/Highlight/OFF:
Press the remote button to turn on the LED.
Press again for Highlight. Press again the remote button to turn OFF the LED.
AC range:
Press the AC, and the RED and WHITE LED will flash alternately.
During the LED is flashing (someone presses the doorbell button), the user can
press the AC6 LR master (Dim / Highlight / OFF switch) to stop the flashing of
the LED.
Remarks:
If there is more than one AC remote device paired with an LED, the LED is
flashing (someone presses the doorbell button). The RED blinking signal
cadency will be different to indicate which AC* has triggered the bulb:
#1: R– W– R– W– R– W– R– W– R.
#2: RR – W – RR – W – RR – W – RR.
#3: RRR – W – RRR – W – RRR.
#4: RRRR – W – RRRR – W – RRRR.
Smoke alarm
If the smoke alarm triggers the bulb, The RED LED will blink.
During the RED LED is flashing user can press the AC6 LR master (Dim /
Highlight / OFF switch) to stop the RED flashing LED.
Troubleshooting
Battery Low:
If the battery of AC6 LR (remote Dim/Highlight/OFF) is low (below 6V),
pressing the AC6 button, can still trigger the bulb, but the LED will not be
ON. This means the battery is low.
Please replace the battery.
Remote battery replacement:
Removal and replacement of battery should be carried out by an adult or under
adult supervision.
Take special care to ensure the battery is inserted correctly, observing (+)
and (-) polarity marks on the battery and product. Remove batteries if you
will not be using the product for long periods.
GUARANTEE
From the moment your Geemarc product is purchased, Geemarc guarantees it for a
period of two years. During this time, all repairs or replacements (at our
discretion) are free of charge. Should you experience a problem then contact
our helpline or visit our website at
www.geemarc.com.
The guarantee does not cover accidents, negligence, or breakages to any parts.
The product must not be tampered with or taken apart by anyone who is not an
authorized Geemarc representative.
The Geemarc guarantee in no way limits your legal rights.
IMPORTANT: YOUR RECEIPT IS PART OF YOUR GUARANTEE AND MUST BE RETAINED
AND PRODUCED IN THE EVENT OF A WARRANTY CLAIM.
Please note: The guarantee applies to the United Kingdom only.
CE Directives:
Geemarc Telecom SA hereby declares that this product is in compliance with the
essential requirements and other relevant provisions of the Radio and
Telecommunications Terminal Equipment Directive 2014/53/UE.
The CE declaration of conformity may be consulted at
www.geemarc.com
Recycling Directives:
The WEEE (Waste Electrical and Electronic Equipment) has been put in place for
the products at the end of their useful life to be recycled in the best way.
When this product is finished, please do not put it in your domestic waste
bin. Please use one of the following disposal options:
– Remove the batteries and deposit them in an appropriate WEEE skip.
Deposit the product in an appropriate WEEE skip.
– Or, hand the old product to the retailer. If you purchase a new one, they
should accept it.
Thus if you respect these instructions you ensure human health and
environmental protection. 
For product support and help visit our website at
www.geemarc.com
5B Swallow Court, Swallow fields, Welwyn Garden City,
Hertfordshire, AL7 1SB, UK
telephone 01707 387602 or fax 01707 832529
QUGAMPLICALL6_En_2/3A4_V1.1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>