Shenzhen Shunxinda Trading Q3171 IP Camera User Manual

Shunxinda Trading Q3171 IP Camera
User Manual Please scan the QR code above to download “V380ProAPP”

Connect the device

The APP en II be updated continuously. and the interface is subject to the APP
Download APP
Use the mobile phone’s “Scan” function to scan the QR code, download and install “V380Pro” Connect power
Connect the device to the power supply for about 1 minute until the following beep sounds: System startup, system startup is complete, the hotspot is being established, the hotspot is established
Wi-Fi connection operation steps
The APP will be updated continuously. and the interface is subject to the APP

Need to resistor user first

1. Log in to the V3S0Pro APP again

2. Click to add equipment

3. Click “YAreless Smart

4. Click ‘AP Hotspot camera’ Connection

5. Click “Please select your own wireless network router Wi-Fi name”

6. Enter the wireless network click to confirm the router Wi-Fi password

7. Click to connect to the hotspot and turn on the phone system settings, connect mobile phone Wi-FiTo the network beginning with “MV”, Go back to the app

8. At this time, the interface appears that the device is connected Please pay attention to the voice prompt of the camera.(Wi-Fi connection/Wi-Fi connection completed)

9. It shows that the addition is complete, Device naming after completion device will appear on the homepage

10. Click “Play button” Set viewing password

11. Go to set the password (This password is a viewing password, please remember it)

12. Please set the device password to complete

AP hotspot without internet operation steps
Need to register a user first

1. Log in to the V38OPro APP again

2. Open the phone system settings, Connect mobile phone Wi-Fi to “MV”At the beginning of the network, then open the APP

3. Click on the blank space and go downhill to refresh, you can discover the device

4. Click “+” to add equipment The phone must always be connected to the WIA starting with MVIf you disconnect the WWI at the beginning of the Mg you can either watch the monitoring screen

5. Click ” ® ” Set viewing password

6. Go to set a password (This password is a viewing password, please remember it)

7.  Please set the device password complete

Function Description
The APP will be updated continuously, and the interface is subject to the APP

Light control instructions:

Auto:  The default black and white  night vision at night,When an object passes by, the full-color night vision is automatically turned on
Normally open: the white light can be turned on manually
Normally off: the white light can  be turned off manually
Alarm description:

Cloud video description

Cloud storage is 24 hours uninterrupted recording throughout the day
A variety of packages are available for purchase:
8G cloud video L experience version; Up to 10 days of uninterrupted recording, Support 1 device.
16G cloud video ex rience version; Up to 20 days of uninterrupted recording, Support 1 device.
128G cloud video ex enhanced version; Up to 160 days of uninterrupted recording, Support 8 devices.
32G cloud video experience version ; Up to 30 days of uninterrupted recording, Support 2 devices.
64G cloud video experience version; Up to 80 days of uninterrupted recording, Support 4 devices.
Cloud storage description:

Click to view a variety of detailed packages, Can choose to buy
You can view the usage of the purchased package
You can view the status of the bound devices, And bind the device to use
common problem

connection between the camera and the router, please connect to the distribution network at close range. Check whether the wifi password is correct and the phone can connect to the network normally. Restart the router, restart the camera, and try to connect to the Internet again.
What if the display device is offline?| First, confirm whether the power supply and network are normal. If there is no problem, power off the camera and restart it. For example, the camera voice prompt system is starting, the system is starting, the wifi connection is in progress, The camera voice prompts that the wifi connection is not completed, which means that the camera cannot connect to the router wifi. Check if the camera is too far away from the router, the signal is not good, and the camera cannot be connected to the wireless wifi. Or reset the camera to factory settings, and then reconnect to the network.
Watch screen display password What should I do if I make a mistake?| Enter the password input that is prompted to set up on the screen when the camera is connected for the first time, The password is a combination of 6-8 digits in English, The factory default user name of the device is admin if there is no change, it is the default factory user name admin, If you have forgotten the password, you need to restore the camera to factory settings, find the camera to restore factory settings button,press and hold for about 10 seconds, and the camera voice prompts to restore the factory settings, you can reconnect to the network settings.

FCC Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
This device complies with RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device must operate with a minimum distance of 20 cm between the radiator and user body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>