geemarc AMPLICALL110 Wireless Telephone Signaler User Guide
- June 4, 2024
- geemarc
Table of Contents
Wireless Telephone Signaler
Please refer to our website: www.geemarc.com for an up to date user guide, as there may be important updates and changes you need to be aware of.
Box Contents
The AC110 (AMPLICALL 110) box contains the following items: TM
1 user’s manual
1 AC110 (AMPLICALLTM 110)
1 RJ11/RJ11 cable| 2 screws and 2 anchors
2 x AA,1.5V Alkaline batteries
1 Drill hole template
---|---
DESCRIPTION
BATTERIES INSTALLATION
Your AMPLICALL™ 110 works with two Alkaline AA 1.5V batteries (not provided).
Please follow the below procedure to insert the batteries. 
- Unscrew the screw on the battery cover.
- Open the battery cover.
- Insert the 2 AA batteries into the compartment.
- Close the battery cover and fix it using the screw.
Low Battery
If your device is running low on battery or if no battery has been inserted,
your APPLICABLE™ 110 will send a signal to the receiver which will make the
zone icon light up.
Connecting your AC110 to the mains (Optional)
Even if your APPLICABLE ™ 110 is plugged into the mains, you must insert
batteries, otherwise, your device will send a low battery signal to your
receiver.
Those batteries will however only work as backup batteries in the event of a
power failure.
Connect the Type C USB power cable to the DC input connector.
Pairing your AC110 with the AMPLICALL™ receivers
The AC110 can work on its own, it will amplify the ringer and will flash when
you receive a call. You also have the possibility to register your AMPLICALL™
110 with the AMPLICALL™ receivers. If paired, the receivers will receive the
information from the AMPLICALL™ 110 and ring and flash as well.
Enter pairing mode for the AMPLICALL receivers.
-
Press & hold the LEARNING button (●) for 3 seconds. The LED in zone icon #1 will flash
-
Press the LEARNING button (●) again to move to the zone icon you wish to pair the AC110 with.
Press the melody selection button to scroll through the melodies. Once you hear a melody you like, do not press any button during the melody. -
Press the bell button of the AC110 to pair.
-
If successful, the AMPLICALL receivers will generate two short tones.
Connecting your AC110 to a phone socket
- Connect one end of the supplied RJ11 cord to your phone socket and the other to the “Tel” input connector on your AC110
- Connect one end of your original phone cord to the “Line” input connector on your AC110 and the other to your wall outlet.
Wall mounting
The AC110 can either be placed on a flat surface or mounted on a wall.
Mark two holes on the wall using a pencil and drill hole template.
Mount the unit to the wall using the provided anchors and screws.
Charging the settings of your AC110
On / Off slide button: Slide to the Off position when no receiver is used.
Volume : You can adjust the volume of the ringer by sliding this button, you
can switch between the H (high), L (low), and X (silent)
positions.
Connecting an External Sensor to your AC110
The AC110 is compatible with external devices such as fall mats and other types of sensors which can be connected to the AC110 using the “EXT” jack socket. Once connected, the device will send a signal to the receiver every time it is triggered.
GUARANTEE
From the moment your Geemarc AMPLICALL ™110 is purchased, the Geemarc
guarantee is for a period of two years. During this time, all repairs or
replacements (at our discretion) are free of charge. Should you experience a
problem then contact our helpline or visit our website at
www.geemarc.com. The guarantee does not cover
accidents, negligence, or breakages to any parts. The product must not be
tampered with or taken apart by anyone who is not an authorized Geemarc
representative. The Geemarc guarantee in no way limits your legal rights.
IMPORTANT: YOUR RECEIPT IS PART OF YOUR GUARANTEE AND MUST BE RETAINED
AND PRODUCED IN THE EVENT OF A WARRANTY CLAIM.
Please note: The guarantee applies to the United Kingdom only.
DECLARATIONS:
UKCA Directives
Geemarc Telecom SA hereby declares that this APPLICABLE™ 110 is in compliance
with the essential requirements and other relevant provisions of the Radio
Equipment Directive 2014/53/UE.
The UKCA declaration of conformity may be consulted at
www.geemarc.com
RF power : < 250mW
Recycling Directives
The WEEE (Waste Electrical and Electronic Equipment) has been put in place for
the products at the end of their useful life to be recycled in the best way.
When this product is finished, please do not put it in your domestic waste
bin. Please use one of the following disposal options:
– Remove the batteries and deposit them in an appropriate WEEE skip. Deposit
the product in an appropriate WEEE skip.
– Or, hand the old product to the retailer. If you purchase a new one, they
should accept it. Thus if you respect these instructions you ensure human
health and environmental protection.
For product support and help visit our website at
www.geemarc.com
E-mail : help@geemarc.com
telephone 01707 387602
lines are open 09h00 to 16h00 Mon to Fri
2 Rue Galilée, Parc de l’Etoile, 59791 Grande-Synthe, France
This product is made in China To Geemarc Telecom
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>