Ensenior Can Light-20220517 12 Pack 6 Inch Ultra-Thin Led Recessed Ceiling Light User Manual
- June 9, 2024
- Ensenior
Table of Contents
Ensenior Can Light-20220517 12 Pack 6 Inch Ultra-Thin Led Recessed Ceiling
Light User Manual
SAFETY INSTRUCTION
Ensenior’ s LED Recessed Downright is certified by ETL & FCC & Energy Star(except 6000K) of a high standard. But to reduce the risk of death, personal injury or property damage from fire, electric shock and other hazards, please read all warnings and instructions included with and on the fixture box and all fixture labels, please review instructions carefully before proceeding.
WARNING
RISK OF ELECTRIC SHOCK
- All electrical concoctions must be in accordance with local and National Electric Code (N.E.C.) standards.
- Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.
- Turn off the switch and circuit breaker before installing this LED light.
- Do not alter, re-locate or remove wiring.
- Double-check all connections to be sure they are tight and correct.
- Verify that supply voltage is correct by comparing it with the luminaire label information.
RISK OF FIRE
- Keep combustibles and other materials that may burn away from lights.
- The maximum ambient temperature is 104°F. Do not operate fixture at temperatures higher than it.
CAUTION
RISK OF INJURY
- Wear gloves and safety glasses at all time when removing luminaire, installing or performing maintenance.
- Avoid direct eye exposure to the light source while it is on.
- wear rubber-soled shoes and work on a sturdy wooden ladder.
RISK OF BURN
- Do not touch enclosure or light source. It is normal of the luminaire surface heating up during work. Allow lights to cool before handling.
RISK OF PRODUCT DAMAGE
- Electrostatic Discharge (ESD): ESC) can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit.
- Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
- Do not let the product directly contact with water. Our product is damp-rated but it is not water-proof.
- Do not make or alter any open holes in an enclosure of wiring or electrical components.
- Never connect components under load.
- Please make sure that all wires in and Out are wired firmly and sufficiently. If not, there will be a flickering issue Or the light will just stop.
IMPORTANT
- Our temperature has been strictly monitored. But the temperature will be Slightly different with varied monitors. PleaSe test them before installation up in the ceiling wall and see the color if it meets your needs.
- If there is anything wrong with our lights, please see the Troubleshooting Page. If you could not I ind an answer in that page, please refer to the Customer Service page and contact us.
ROUTINE MAINTENANCE
- Please make sure the power is off before maintenance.
- To avoid any damage to the product, please do not use any chemical solvents during the routine maintenance.
- To ensure better lighting, please clean the lamp at regular intervals.
LIMITED WARRANTY
This product is warranted to be free from defects in workmanship and materials
for up to 5 years from date of purchase.
if it lets to do so, pease contact the Customer Service Teom at +1(213)-296-2111 or Vist [email protected].
STEP BY STEP INSTALLATION
Each light contains the following parts:
1 x Light Part
1 x Cable with E26 Adapter
2 x Spring
2x Screw
Screw the springs to the correct position for either 5″ or 6″ can.
Locate the correct size and screw them tight.
Choose the color temperature that you need. Flip the black switch to the color
setting that you like.(Skip this step if you bought single-color lights.)
Screw the E26 base adapter into the can. If you already equipped the can with
the cable, just skip this step.
Connect the connector of the TP24 cable with the connector of the light.
Push up the spring holders to insert the light fixture into the can.
Turn on the light. If the color setting is not what you want, repeat No.2 to
No.6 steps.
SPECIFICATIONS
- Voltage: 120V
- Wattage: 12W
- Current: 1A
- Power Factor: 0.75
LIGHTING PERFOMNACE
- Lumens: 1100LM
- Equivalency: 110W
- Color Temperature: 2700K/3000K/4000K/5000K/6000K/5CCT*
- Color Rendering Index(CRI): > 90
- Beam Angle: 90°
- Dimmable: Yes
- Effciency(Im/w): 92 Im/w
- Operating Temperature: 14F°-104F°
ENVIRONMENT
- Suitable for Damp Location Ingress: Yes
- Application: Indoor Only
CONSTRUCTION
- Housing Material: Metal (SPCC+PC)
- Weight: 240g
LIFESPAN
- Average Life(hours): 50000+
- Warranty: 5 years
***** 5001=2700K/3000K/3500K/4000K/5000K
DIMMER COMPATIBILITY GUIDE
| Model | Feature | Rating |
|---|---|---|
| Lutron | FP: Forward Phase Control | RP: Reverse Phase Control |
| DVCL-153P(FP) | 3-way, 150W | |
| DVCL-253P(FP) | 3-way, 250W | |
| DVWCL-153PH(FP) | With Wallplate | |
| LECL-153P(FP) | 3-way, 150W | |
| LGCL-153P(FP) | 3-way, 150W | |
| SCL-153P(FP) | 3-way, 150W | |
| AYCL-153P(FP) | 3-way, 150W | |
| TGCL-153PH(FP) | 3-way, 150W | |
| CTCL-153P(FP) | 3-way, 150W | |
| CTCL-150H(FP) | Single pole/150W ****1 | |
| STCL-153P(FP) | Touch, 150W | |
| MACL-153M(FP) | Digital, 150W | |
| MACL-153M-RHM(FP) Digital, Kit | NTRP-250(RP) | |
| MA-PRO(FP) Digital, Pro | ||
| Zen27(FP) | Z-wave Smart |
CUSTOMER SERVICE
12 HOURS QUCIK RESPONSE
If there is any problem with our light, please refer to the Troubleshooting
page on the back. If you still could not fix this, please contact us
immediately. It doesn’t matter if you have installed the product, we will
respond within 12 hours.
The fastest way to hot, us conivin the problem ■s tO Seed US EtV000 Of proteemaric Ognr to our othcalemml box.
30-DAY MONEY-BACK
For 30 days after the date of purchase, return your Ensenior product and receive a full refund for ANY reason.
5-YEAR WARRANTY
For 5 years after the date of purchase, if there is any issue with the product, we will send a new product for free or a full refund. (no need to return the purchased product)
Under most conditions, ire will not require you to return the purchased items. Sure, if you would return the defective one(s) to us, we will be very happy for that would help us to make continuous improvements.
Free Replacement No Repair
After the buyer purchases the product, if the product has a quality problem within the scope of the seller’s warranty service within the service validity period, the seller will replace the buyer with a new product for free.
Friendly Reminder
We sincerely hope to solve the problem for you. We do not recommend that you leave a product rating first, because we cannot obtain your contact information through the review/feedback, nor can we obtain your relevant information and provide you with compensation.
Please rest assured that our service aim is to make customers 100% satisfied. If there is any problem, please contact us as soon as possible, we will not let you down.
COMMON TROUBLESHOOTING
We are an LED manufacturer with 10-year experiences and receive feedback from more than 1000 customers every year. According to our statistics, 95% of customers’ problems are related to the method of installation and the use of dimmer, which could be solved by customers themselves. To save your valuable time, please read this introduction first to quickly identify the cause, if you encounter any problems.
Problems you may encounter
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
|---|---|---|
| Unlit | the wire falls off/ looSenS/ breaks | Double check the connection of the |
wire.
the connector is missing or the connector lacks metal shrapnel| Double check
the connector.
Voltage is too high| Install the lights on 120 volts.
Dim| the wire falls off/ loosens/ breaks| Double check the connection of the
wire.
not setting the dimmer right| Double check the setting.
compatible dimmer, but too many lights connect to one dimmer| Reduce the
number of lights connected to the one dimmer. (Total Power of the Lightss75%
of the Rated Power of the Dimmer)
Flickering| Buzzing noise from dimmer/ circuit break| Double check the
connection of the wire.
not setting the dimmer right| Double check the setting.
(x) incompatible dimmer| Select a dimmer from the recommendeddimmer list.
Compatible dimmer, but too many lights connect to one dimmer| Connect fewer
lights to the one dimmer. (Total Power of the Lightss75% of the Rated Power of
the Dimmer)
High-power electrical appliances on the same circuit| Remove and set them
further away from each other.
Buzzing Noise from dimmer/circuit break-er (>20Db)| (x) incompatible dimmer|
Select a more compatible dimmer from the recommended dimmer list .
compatible dimmer, but too many lights connect to one dimmer| Reduce the
number of lights connected to the one dimmer. (Total Power of the Lightss75%
of the Rated Power of the Dimmer)
(x) incompatible circuit breaker| A. mechanical circuit breaker: replace a
compatible dimmer. B. Electronic control circuit breaker: replace the circuit
breaker first.
high-power electrical appliances on the same circuit(radio, air condition-ers,
refrigerators, etc.)| Remove and set them further away from each other.
Contact US
Contact by “Ask a quesion” on the “Ensenior” Seller Page.(7x24H)
Because Amazon’s information system sometimes can’t successfully receive and send information, in which foe NV anoa toc Mel lectern Ma MTT Um Alo MOC NACo ae UA Molar Rta La Mac Varo Bors elale Xo COU RUA mN el eS Ue UA CuI
Contact via Email:
[email protected](7x24H)
ce-) IVI +1(213)-296-2111(Monday-Sunday 5:00p.m.-9:00p.m. PST)
Scan the QR code to fill the form, you will got 1 Free EXTRA YEAR Warranty.
You also get the chance of participating our FREE PRODUCT TRIALS and getting
Coupon!