wiltec 62806 Hose Reel Cart User Manual
- June 4, 2024
- wiltec
Table of Contents
wiltec 62806 Hose Reel Cart User Manual
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Illustrations, functional steps, and technical data may deviate
insignificantly due to continuous further developments.
Updating the documentation
If you have suggestions for improvement or have found any irregularities,
please contact us.
Introduction
Thank you for choosing to purchase this quality product. To minimise the risk
of injury, we ask you to always take some basic safety precautions when using
this product. Please read this operating manual carefully and make sure that
you understand it.
Keep these operation instructions in a safe place.
Safety instructions
- It is advisable to observe the following safety instructions. This hose reel cart has been designed, constructed, and tested so that its operation is safe and efficient, provided that it is used exactly according to this user’s manual. Any non-observance might lead to injuries.
- Always respect the instructions for a safe operation. Carefully read the user’s manual and keep it at a safe place.
- Look out for holes and other dangers in the ground. Follow the maintenance and lubrication instructions, as stated in this user’s manual. Always wear robust shoes. Do not wear loose clothing that could get caught in moving parts.
Parts list
| No | Name | No | Name |
|---|---|---|---|
| 1 | Side frame | 14 | Crank holder |
| 2 | Cross bar | 15 | Hose washer |
| 3 | Axle | 16 | M6×35 screw |
| 4 | Wheel | 17 | M6×30 screw |
| 5 | Ends of hose reel | 18 | M8 nylock nuts |
| 6 | Sliding hoop | 19 | Splint |
| 7 | Connection rods | 20 | Large M12 washer |
| 8 | Hose coupling | 21 | Small M12 washer |
| 9 | Hand crank | 22 | M6 nylock nuts |
| 10 | Hose extension | 23 | Front crank frame |
| 11 | Basket | 24 | M8 washers |
| 12 | U-shaped holder | 25 | M8 U-shaped holder screw |
| 13 | Crank holder |
Assembly
To assemble the cart, the following tools are required:
- screwdriver
- M10 wrench or adjustable spanner
Step 1
- Use two sets of M6×35 screws to mount the front crank frame to the side frame. Then use four sets of M6×35 screws to attach the cross bar to the side frame.
- Slide the axles through the flaps of the underside of the side frame.
| No | Name |
|---|---|
| 1 | Cross bar |
| 2 | Front crank frame |
| 3 | Side frame |
| 4 | Axles |
Step 2
Use a large 12 mm washer and a splint to mount the wheels.
Step 3
Fix the end of the hose reel to the connection rods by using the M8 nylock nuts and corresponding washers. Repeat this on the opposite.
| No | Name |
|---|---|
| 1 | Connection rod |
| 2 | M8 nylock nuts and washers |
Fix the hose coupling to the middle hub by using the varnished U-shaped holder and the set of M8 screws.
| No | Name |
|---|---|
| 1 | U-shaped holder |
| 2 | Hose coupling |
Step 4
Fix the basket to the handle by using the sets of M6×35 screws.
| No | Name |
|---|---|
| 1 | M6×35 screws |
| 2 | Basket |
Step 5
Insert the washers into the hose extension and hose coupling.
Step 6
Fix the hose extension to the hose coupling.
Maintenance hints
- Kept clean and dry, this cart will have a longer service life.
- Regularly lubricate the wheels, at least every 6 months; in case the cart is used regularly, the wheels will require a more frequent lubrication.
- In case rust forms, slightly grind the rusty spots and spray them with varnish.
Important Note: Reproduction and any commercial use (of parts) of this operating manual, requires a written permission of WilTec Wildanger Technik GmbH.
The information contained in this document may alter at any time without prior
notice. No part of this document may be copied or otherwise duplicated without
prior written consent. All rights reserved.
WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes
in this operating manual, nor in the diagrams and illustrations shown.
Although WilTec Wildanger Technik GmbH has made every possible effort to
ensure that this operating manual is complete, accurate, and up-to-date,
errors cannot be ruled out entirely. If you have found an error or wish to
suggest an improvement, we look forward to hearing from you.
Send us an e-mail to: service@wiltec.info or use
our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in
our online shop:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler – Germany
To return your goods for exchange, repair, or other purposes, please use the following address. Attention! To allow for a trouble-free complaint or return, it is important to contact our customer service team before returning your goods.
Retourenabteilung
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler – Germany
E-mail: service@wiltec.info
Tel: +49 2403 55592–0
Fax: +49 2403 55592–15
https://www.XPOtool.com
The Tool Experts
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>