clearaudio AC163 Weight Watcher Touch User Manual

June 9, 2024
clearaudio

clearaudio logo Loving music
Weight Watcher touch
User manual
clearaudio AC163 Weight Watcher Touch -

AC163 Weight Watcher Touch

Dear Clearaudio customer,
Thank you very much for choosing the Weight Watcher touch from
Clearaudio Electronic GmbH.
This digital Clearaudio cartridge weighing scale allows you to achieve an extremely precise adjustment of tracking force, which in turn will enable the optimum performance of your phono cartridge.
With the Weight Watcher touch, you have a precision instrument to hand that allows you to check and set the required tracking force quickly, easily and exactly.
Please note:
This user manual gives you valuable information for the correct use of the Weight Watcher touch.
We would like to thank you for your purchase.
Clearaudio electronic GmbH

Safety instructions

  1. Transportation
    • If you transport or ship the Clearaudio Weight Watcher touch for any reason, the original packaging must be used. Please pack the unit as it was packed originally by Clearaudio to ensure secure transport.

  2. Service
    • The Weight Watcher touch should only be repaired by Clearaudio approved institutions or persons, or by Clearaudio, otherwise the warranty will be void.

  3. Special instructions
    3.1 Auto-Off
    If the device is not used for more than 3 minutes, it automatically switches off to save the battery.
    3.2 Overload indicator
    If the capacity is exceeded, the display shows ‘O-LD’. Immediately remove the load and check the functionality of the Weight Watcher touch with the enclosed calibration weight. Bear in mind that you can permanently damage the Weight Watcher touch and your warranty claim will expire due to overload.

  4. Safety instructions
    CE Mark
    This electronic product complies with the valid guidelines for obtaining the CE mark.
    Disposal
    **** This product is not allowed to be disposed with household waste.
    WEEE Reg.No.: DE26004446

Delivered items

  • Weight Watcher touch incl. 2x CR2032 batteries
  • Calibration weight 100g
  • User manual

Further analogue accessories available at: www.analogshop.de

Measuring procedure

Before using the Weight Watcher touch for the first time, remove the battery seal from the battery compartment on the back of the device.
Select the unit
To adjust the tracking force, we recommend using the default setting: ‘g’.
If you want to use another unit of measurement, you can select it by ‘MODE’.
Determine the correct position of your Weight Watcher touch on the turntable by carefully positioning your tonearm with the cartridge in the playing area of the turntable.
The measuring area of the Weight Watcher touch (marked ‘Measuring area’) is at the same height as a 200g vinyl pressing, so the measurement should be made without a record on the platter.
Carefully place your Weight Watcher touch on the turntable’s surface.
Make sure that all 4 small nubs on the underside of the Weight Watcher touch rest on the turntable platter and not in the label recess of the platter.
This ensures accurate measurements.
Now you can switch on the Weight Watcher touch by tapping on the ‘ON /OFF’ area. After switching it on, all elements of the display are displayed for approx. 3 seconds before returning to ‘0.0’.
Place the tonearm with the cartridge on the red-marked measuring area.
Slowly lower the tonearm, so that the stylus is centred on the red dot.
To avoid false measurements, the body of the cartridge should never contact the Weight Watcher touch.
The display now shows you the weight in grams. If this does not match the cartridge manufacturer’s specification, lift the tonearm and correct the tracking force.
Check your final adjustments of the tracking force again with the Weight Watcher touch.

– Please note –
Horizontal placement of your Weight Watcher touch is required for accurate measurement of tracking force.
Do not touch the surface (calibration area, showing the Clearaudio logo) during the measurement process to ensure an accurate measurement.

clearaudio AC163 Weight Watcher Touch - Measuring area

Changing the batteries

If the Weight Watcher touch cannot be switched on, the batteries should be replaced.
To change the batteries, open the battery compartment by pressing the lock and remove the cover. Pay attention to the polarity when inserting the batteries. Now you can replace the cover.
Use caution and do not apply any pressure to the calibration /measurement surfaces!

Calibration

If the measurements shown seem inconsistent use the supplied calibration weight to recalibrate the Weight Watcher touch.

  1. Place the Weight Watcher touch on a flat, stable surface.
  2. Hold down the ‘MODE’ button for approx. 3 seconds: the display will show ‘CAL’ and then the required calibration weight.
  3. Place the 100g weight (included) centered on the calibration area (where the Clearaudio logo is shown) and wait 3 seconds.
  4. Press ‘ON/OFF’. The display will show “PASS”.

The calibration is completed.
We wish you a lot of fun.

Technical data

Measuring accuracy: +/- 0.01g
Measuring range: 0 – 100g
Units: g, oz, ct, gn
Power source: 2x CR2032 Batterien
Auto-Off: After 3 minutes
Weight: approx. 64g
Dimensions (B/T/H): 3.50 x  2.97 x 0.53 inches
Dimensions (B/T/H): 89 x 75.5 x 13.5mm
Manufacturer‘s warranty: 2 years (except batteries)

Only if the product is returned in its original packing Clearaudio can provide the warranty of 2 years.

WARRANTY
For warranty information, contact your local Clearaudio distributor.
RETAIN YOUR PURCHASE RECEIPT
Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Clearaudio.
IMPORTANT
When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. Your purchase receipt or invoice is adequate for such proof.
FOR U.K. ONLY
This undertaking is in addition to a consumer‘s statutory rights and does not affect those rights in any way.

clearaudio electronic GmbH
Spardorfer Straße 150
91054 Erlangen
Germany

Clearaudio Electronic accepts no liability for any misprints.
Technical specifications are subject to change or improvement without prior notice.
Product availability is as long as stock lasts.
Copies and reprints of this document, including extracts, require written consent from
Clearaudio Electronic GmbH, Germany.

Phone /Tel.: +49 9131 40300 100
Fax: +49 9131 40300 119
www.clearaudio.de
www.analogshop.de
[email protected]

2022
© clearaudio electronic GmbH
Made in Germany

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

clearaudio User Manuals

Related Manuals