clearaudio CLEASP24V Smart Power 24V Battery Power Supply User Manual

June 6, 2024
clearaudio

clearaudio CLEASP24V Smart Power 24V Battery Power Supply

Contents

Please check all contents of your package:

  1. smart power 24V (with hard wired power cord, length 200cm)
  2. IEC power cable
  3. User manual
  4. Warranty card / Quality card

Getting started

The Clearaudio smart power 24V is delivered in custom-designed packaging. Please keep this packaging to ensure safe transportation if needed.
Unpack the unit and place it at its desired location.
Connect the smart power 24V to the mains power supply with the supplied IEC power cable. Then connect your turntable to the smart power 24V using the attached power cord, instead of the usual power supply

To switch the smart power 24V on, use the switch on the rear side of the unit.
The smart power 24V will start automatically and displays following:

After completing the powering-up process, which takes approx. 20 seconds, the LCD display get dimmed and the button will turn off. The unit is now in the output/off mode.

To activate the unit, press the button (approx. 5 seconds) till the button and the screen brighten up and show the following screen:

Before using smart power 24V it is important to fully charge the internal batteries to bring them to the optimum operating condition (see page 6, point 4.3, “Charging mode”).

Display screens

By pressing the front panel button shortly it will cycle through various display screens.
A long press will activate the particular function:

*Status information:**
Shows the approximate battery charge level.

Top-Up Battery?:
If the battery is fully charged (+99%) and the unit is not charging the display shows “Top-Up Battery?”.

START Charging?:
If the battery is not fully charged (<99%) and the unit is not charging the display is showing “START Charging?”.

STOP Charging?:
If the battery is being charged then the display shows “STOP Charging?”.

*Output information:**
Advises whether the unit is in charging mode or battery mode, and the battery output current

*Charging information:**
Shows the charging battery voltage and current.

Adjustment of the brightness while operating the unit:
With the display in this position a long press of the front panel button will adjust the display brightness.

Adjustment of the brightness while the unit is in output/ off mode or 30 seconds after not operating the unit:
With the display in this position a long press of the front panel button will adjust the display brightness.

*Note: All numbers shown in the display images above are examples.
Actual readings will vary depending on smart power 24V’s status and run time

Modes of operation

Output/off mode

The output/off mode is characterized by:

  1. The output is deactivated.

  2. The screen is dimmed and shows:

  3. The LED ring of the button is off.

Note: In this mode, if the battery is discharged, the unit will start charging the battery automatically.

Battery output mode

The battery output mode is characterized by:

  1. The output is activated.

  2. The screen is dimmed (if the unit is not operated for more than 30 seconds) and shows:

  3. The LED ring is constantly on (not flashing).

Charging mode

The charging mode is characterized by:

  1. The output is activated.

  2. The screen is dimmed (if the unit is not operated for 30 seconds) and shows:

  3. The LED ring of the button is flashing.

If the unit becomes completely discharged, smart power 24V will automatically switch to charging mode.
To manually start the charging or top-up process, go to “START Charging?” or “Top-up battery” screen and confirm with along press (5+ seconds). The display confirms the activated charging mode and then changes back to the status information. Depending on the remaining charge of the integrated NiMh batteries, the charging time may vary.
When the battery is fully charged, the charging mode will switch off automatically.

To manually stop the charging process, go to “STOP Charging?” screen and confirm with a long press. The display confirms the stopped charging process with following display.

Please note:
The unit will take up to 30 seconds to completely start or stop the charging process.

Operating information

  • If the front button is not pressed for 30 seconds the display returns to “Status information” (see page 5).

  • As long as a load is connected to the smart power 24V and the remaining charge level is sufficient for operation of the connected device there will be no charging.

  •  A reduction of the output voltage of up to 4V between two charging cycles is normal.
    Crucial for the correct speed of the turntable is a noise free current and not the absolute value.
    This is ensured by battery-buffering and a special, linear regulation in the turntable.

  • Switching off the unit is done using the power switch on the rear side of the smart power 24V .

Please note:
To prevent overheating of electronic parts never cover or put anything on top of the smart power 24V.
Do not dispose the unit in the domestic waste.
Do not expose the smart power 24V to a temperature above 40° Celsius

Technical Data

Battery: NiMh Battery with 5000mAh
Power supply: 100-240V AC, 50-60Hz, max. 1.4A
Output: 24V DC, max. 1.6A; fused (time delay fuse)
Power consumption in operation mode: 6.5 – 33 watts (depending on the

charge cycle)
Power consumption in off mode:| 0 watts (turned off at rear panel)
Weight:| Approx. 5.7 kg
Dimensions (w x d x h):| 8.27 x 12.00 x 4.92 inches 210 x 305 x 125mm
Warranty:| 3 years* (except batteries)

* Provided that the warranty card is correctly completed and returned to Clearaudio, or your product is registered online athttps://clearaudio.de/en/service/registration.php, within 14 days of purchase.

Clearaudio electronic GmbH
Spardorferstraße 150
91054 Erlangen
Germany
Phone: +49 9131 40300100
Fax: +49 9131 40300119
www.clearaudio.de
www.analogshop.de
info@clearaudio.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals