SURFACE MAXX SGY-PWA77 Stainless Steel Pressure Washer Surface Cleaner Instructions

SURFACE MAXX SGY-PWA77 Stainless Steel Pressure Washer Surface Cleaner

PACKAGE CONTENTS

A| Stainless Steel Pressure Washer Surface Cleaner| 1
B| Nozzle Cleaning Tool| 1

PRODUCT SPECIFICATIONS

• Connections: 1/4 in. Quick Connect Plug w / Filter Installed
• Maximum Pressure: 4500 PSI
• Maximum Water Flow: 4.0 GPM
• Maximum Water Temperature: 230 °F/ 110 °C
• Weight: 7.5 lbs.

SAFETY INSTRUCTIONS

WARNING:
When using this product basic precautions should always be followed, including but not limited to the following:

1. Observe the safety instructions of your pressure washer.
2. The Surface Cleaner must not be used by children.
3. Only trigger the gun of the pressure washer if the Surface Cleaner is on the surface to be cleane
4. Keep all persons/animals clear of the immediate vicinity of the cleaning head.
5. Keep hands away from moving parts.
6. Turn off the pressure washer and relieve the pressure when examining or changing the Surface Cleaner and after the completion of the cleaning operation.
7. Maximum water temperature allowed is 230 °F/ 110 °C. Follow the instructions for your pressure washer.

CAUTION:

1. The Surface Cleaner is not suited for scouring or scrubbing.
2. Do not run over freestanding corners.
3. Test the Surface Cleaner in an inconspicuous area .
4. Not to be used on vertical surfaces.

INTENDED USE

1. The Surface Cleaner can be used with Electric and Gas pressure washers from 2800 to 4500 psi.
2. Use on horizontal surfaces like driveways, patios, sidewalks, etc.

RECOMMENDATION

1. It is recommended that a high pressure filter be purchased to prevent the nozzles from getting clogged.

ASSEMBLE

1. The surface cleaner comes completely assembled and ready for use .

2. Attach the surface cleaner’s 1/4 in. quick connect plug into the end of the pressure washer wand (See Figure 1 ).

3. Connect hose to the pressure washer and start pressure washer as described in its Owner’s Manual.
   CAUTION:

4. Risk of injury can occur if the surface cleaner 1/4 in. quick connect plug is not properly inserted into the quick connect coupler. Make sure you hear a “click” sound when attaching the 1/4 in. quick connect plug to the quick connect coupler .

5. Pull the Surface Cleaner to make sure it is seated properly before operating your unit

OPERATION

1. Squeeze the trigger and moving the surface cleaner back and forth and / or side to side begin to cleaning .

2. Never operate in the same area for more than 2 seconds, damage may occur.
   NOTE: If striping or swirling occurs:

3. Slow your pace and try cleaning the area by going back and forth and side to side .

4. Try overlapping when cleaning by 50% .

5. Check to see if one or both of your nozzles are clogged.
   Follow the maintenance instructions below.
   NOTE: Always squeeze the gun’s trigger to release any residual pressure immediately after use. Engage the rigger lock when not in use.
   CAUTION:
   Striking any raised obstacle while using the surface cleaner could damage the unit. If contact does occur and causes vibration when operating the surface cleaner, stop use immediately. Continuing t operate the unit could result in serious injury

MAINTENANCE

A clogged or dirty nozzle will result in excessive pump pressure causing a pulsing sensation and / or excessive libration.

1. Turn off the pressure washer and turn off the water supply. Release the residual pressure by squeezing the gun’s trigger .

2. Disconnect the pressure washer wand from the surface cleaner .

3. Using a 9/16″ wrench (not provided) remove both nozzles from the spray bar. (See Figure 3)

4. Using the nozzle cleaning tool, free any foreign material clogging or restricting opening of the nozzles. (See Figure 4)

5. Flush debris out of the nozzle. Direct the flow of water through the nozzle backwards from the outside to the inside .

6. Attach the wand back to the surface cleaner, set the surface cleaner on a flat surface. Turn on the water
   (DO NOT START THE PRESSURE WASHER) and squeeze the trigger on the gun. Allow water to run through the spray bar for approximately 30 seconds.

7. Reinstall the nozzles to the spray bar. Tighten securely. Align the nozzle opening as shown in Figure 5.

   • NOTE: Make sure the grove on the face of the nozzle is parallel to the spray bar.
   • NOTE: If the nozzles are not cleaned or aligned correctly he spray bar will not rotate properly and it will not cleans intended and may have a severe vibration.
   • WARNING: STOP USING THE SURFACE CLEANER, CONTINUING TO USE THE SURFACE CLEANER MAY DAMAGE THE SHROUD.
   • NOTE: If your spray pattern begins to change, it could mean that the nozzles are worn and they will need to be replaced.
   • NOTE: If reoccurring problems with the nozzles getting clogged, you may want to consider adding an in-line filter. You can contact us at +1 866-870-9930 or email us at Support@surfacemaxx.com or more details.

ACCESSORIES SOLD SEPERATELY THAT MAKE YOUR SURFACE CLEANER EVEN BETTER

• HIGH PRESSURE FILTER #SGV-PWA99
  Screens out small particles that clog spray nozzles on surface cleaners, water brooms and turbo nozzles.

• 36-IN SPRAY WANO #SGV-PWABB
  Greater comfort that extends reach while using surface cleaners and other accessories.

• WATER BROOM #SGV-PWA97
  Sweeps away dirt and grime with a time-saving 14-in wide cleaning path.

visit www.surfacemaxx.com for even more

REPLACEMENT PARTS LIST

WEBSITE: www.surfacemaxx.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>