Cell2 ED6 3+3 LED Dual Colour Lighthead User Manual

: June 9, 2024
: Cell2

Table of Contents

DUAL COLOUR 3+3 LED DUAL COLOUR LIGHTHEAD
- WIRING
- OPERATION
SINGLE COLOUR 6 LED SINGLE COLOUR LIGHTHEAD
Read User Manual Online (PDF format)
Download This Manual (PDF format)

86-M07710-0001.0

DUAL COLOUR 3+3 LED DUAL COLOUR LIGHTHEAD

WIRING

To Chassis Ground: ……………………………….. BLACK
To+VDC for Warning Mode (1) (fuse @ 1A): ……… RED
Default Colour Mode – Colour 1
To+VDC for Warning Mode (2) (fuse @ 1A): ….. WHITE
Default Colour Mode – Colour 2
(To+VDC for Warning Mode (3): ……….. RED+WHITE)
Default Colour Mode – Colour 1 alt. 2
Order of Precedence: Mode (3) > Mode (1) = Mode (2) > Cruise Mode
To+VDC for Cruise Mode (fuse @ 1A): ……….. GREEN
For Synchronization and Flash Pattern: … YELLOW
Connect YELLOW wires of all lightheads together for synchronization.
(All lightheads should be set to the same Flash Pattern)

OPERATION

For Flash Pattern Selection:

Each Warning Mode may select and save one Flash Pattern. While activating a Warning Mode, momentarily apply YELLOW wire to +VDC :

Once to next pattern.
Quick three times to the default Flash Pattern (FP#1).
(refer to Flash Pattern Chart)

For Simultaneous or Alternating Synchronization:

Apply +VDC to RED (or WHITE or RED+WHITE ) and YELLOW wires simultaneously to enter SETTING MODE; the lighthead will display short flashes:
• Single flash = Group 1 • Double flash = Group 2
Remove YELLOW wire from +VDC then momentarily apply to +VDC again for more than 3 seconds to change Groups:
• Lightheads of the same Group will flash together.
• Lightheads of the different Group will flash alternately.
Save and exit SETTING MODE by disconnecting all power.

NOTE: All warning modes share the same Group setting.

For Color Mode Setting:

Each Warning Memory may select and save one Colour Mode. Apply +VDC to RED (or WHITE or RED+WHITE ) and YELLOW wires simultaneously to enter SETTING MODE; the lighthead will display its current Colour Mode:
• Single Colour flashing Color 1 = Color 1
• Single Colour flashing Color 2 = Color 2
• Dual Colour flashing Color 1 = Color 1 alt. 2
• Dual Colour flashing Color 2 = Color 2 alt. 1
Remove YELLOW wire from +VDC then momentarily apply to +VDC for less than 3 seconds to change Colour Mode.
Save and exit SETTING MODE by disconnecting all power.

Reset to Factory Default Settings:

Apply +VDC to RED (or WHITE or RED+WHITE ) and YELLOW wires simultaneously to enter SETTING MODE;
Remove YELLOW wire from +VDC then momentarily apply to +VDC again for more than 5 seconds. The lighthead will display fast short flashes to signify restoring successfully.
Save and exit SETTING MODE by disconnecting all power.

Flash Pattern (Dual Colour)

1

| Double [2Hz]|

8

| Double [SAE]|

15

| Single-Quad|

22

| Triple-Triple Fast

2

| Single [2Hz]|

9

| Triple [SAE]|

16

| Single H/L|

23

| Quint-Triple

3

| Triple [2Hz]|

10

| Quad [SAE]|

17

| Single-Triple-Quint|

24

| 7-1 Flash

4

| Quad [2Hz]|

11

| Quint [SAE]|

18

| Steady Scene|

25

| 7-1 Flash #

5

| Random|

12

| Mega|

19

| Single-Single|

26

| Quad-Single

6

| Steady EF*|

13

| Giga|

20

| Double-Double|

27

| Quad-Single#

7

| Single [SAE][CA13]|

14

| Ultra [SAE]|

21

| Triple-Triple Mid|

28

| Quint-Quint

FP#19~28 will always operate in dual colour.

For use with external flash controller. # Inverted colour mode.

SINGLE COLOUR 6 LED SINGLE COLOUR LIGHTHEAD