Cell2 Commander SE4 Traffic Director 8 Lighthead User Manual

Commander SE4 Traffic Director 8 Lighthead
User Manual

INSTALLATION

1. Remove endcap (side without cable) and insert mounting carriage bolts.
2. For Surface Mount, drill 1/4″ (6.3mm) holes to the mounting surface.
3. Place Disk Gasket onto each bolt, and insert bolts into mounting holes.
4. Place Lockwasher and Elastic Stop Nut onto each bolt, and tighten firmly.
5. For Bracket Mount (sold separately), refer to mounting bracket manuals.

POWER WIRING RED

RED to +VDC (with fuse according to the following chart)

BLACK: to Chassis Ground

CONTROL WIRING FOR WARNING STICKS

WHIIT for Simultaneous or Alternating Flash
Groupl: Sticks with MOE connected to RED will flash together
Group2: Sticks with WROTE not connected to RED will flash together
Groupl will alternate with Group2
YELLOW: for Synchronization & Flash Pattern Change (refer to Flash Patterns chart)
Connect YELLOW wires of all sticks together for synchronization All sticks must be set at the same pattern
Note: Some patterns are not be suitable for synchronization.

FP#| FLASH PATTERN| FP#| FLASH PATTERN| FP#| FLASH PATTERN
---|---|---|---|---|---
0| Kit Scan| 9| Quint (split)| 18| Mega (all)
1| Outside-In Single| 10| Mega (split)| 19| Ultra (all)
2| Outside-In Ultra| 11| Ultra (split)| 20| Single-Quad (all)
3| Side-by-Side Single| 12| Single-Quad (split)| 21| Single H/L (all)
4| Side-by-Side Ultra| 13| Single H/L (split)| 22| Steady 2 (california)
5| Random| 14| Single (all)| 23| Steady 4 (all)
6| Single (split)| 15| Double (all)| 24| Left Chaser
7| Double (split)| 16| Quad (all)| 25| Right Chaser
8| Quad (split)| 17| Quint (all)| |

(split)=side by side alternating (aII)=all LEDs on
Momentarily apply +VDC to YELLOW wire:

• Once for next pattern
• Quickly 3 times for reset to FP#0

Note: This unit is not factory set at FP#0
The following FP# are not available in 2 Head Sticks: FP# 0, 1, 2, 3, 4, 24, 25

CONTROL WIRING FOR TRAFFIC ARROW STICKS

ORANGE: to +VDC for Left Arrow
ORANG E+BLUE: to +VDC for Center Out
BLUE: to +VDC for Right Arrow
BROWN: to +VDC for Warning Patterns (Arrow Function wires must be deactivated).
YELLOW : for Pattern Change (refer to Flash Patterns chart)
GREEN: to +VDC for Low Power (disconnect for High Power) or for end flasher heads on/off (only for models with end flashers)
WHOTE: only used when connecting with SW610-TA switch (sold separately)
Note: The correct side up is facing the front of the stick with wiring coming out the right side.

FP#| ARROW PATTERNS (ORANGE/BLUE)| WARNING PATTERNS (BROWN)| END FLASHER PATTERNS (GREEN)
---|---|---|---
0| Sweep Single| Random| Random
1| Sweep Double| Outside-In Single| Single (split)
2| Sweep Triple| Outside-In Ultra| Quad (split)
3| Sweep Single End x2| Side-by-Side Single| Mega (split)
4| Solid| Side-by-Side Ultra| Ultra (split)
5| Solid End2| Kit Scan| Single-Quad (split)
6| Solid Chaser| Single (split)| Single (all)
7| Solid Fade| Ultra (split)| Quad (all)
8| Blink Double| Single H/L (split)| Ultra (all)
9| Blink Triple| Single (all)| Single-Quad (all)
10| Blink Solid| Ultra (all)| **In-Sync-Mode

(spli )=side by side alternating
(all)=all LEDs on in-Sync-Mode:
Note: to select End Flasher Patterns, Arrow and Warning Function wires must be deactivated.
Momentarily apply +VDC to wire:

• Once for next pattern
• Quickly 3 times for reset to FP#0

Note: This unit is not factory set at FP#0 during warning mode, end flasher heads will sync according to the warning pattern.
CONNECTION TO SW610-TA SWITCH PANEL (sold separately)

1. Choose a place to install the Switch Panel. 2. Route Switch Panel RED & BLACK wires toward vehicle battery. 3. Route Traffic Arrow Stick wires to Switch Panel and splice same color wires together.

Console Mount Installation

1. Check that all parts are present.
2. Flip to the rear side and position Switch Panel accordingly.
3. Secure Mounting Flaps with screws so that they firmly pinch the Console Panel.
4. Splice wires with Traffic Arrow Stick wires and mount Console Panel onto Console.

Screw Mount Installation

Note: do not splice RED and BLACK wires with Traffic Arrow Stick wires. They must be connected to +VDC and ground.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>