CHRISTIE Griffyn 4K50 Enterprise Lens Hoods Instruction Manual
- June 1, 2024
- CHRISTIE
Table of Contents
Installing the Enterprise
lens hoods
The illustrations in this document are for representation only and may not
depict your projector model exactly.
This instruction sheet describes how to install the Christie M 4K RGB Series
and Griffyn Series lens hoods.
Affected products
The following products are affected:
- Christie M RGB Series
- Griffyn Series
The lens hoods are not required when the Christie M 4K25 RGB and Christie M 4K+25 RGB models are used in low line mode.
Projection lenses requiring lens hoods
The following outlines the projection lenses requiring lens hoods and the position for the lens clamp on the lens hood.
Lens| Part number| Lens clamp position| Projector| Lens
hood| Part number
---|---|---|---|---|---
High brightness
1.95-3.26:1| 144-131106-XX| 2| Griffyn 4K50| 30 mm| 163-170109-XX
2.71-3.89:1| 144-107109-XX| 2| Griffyn 4K50| 185 mm| 163-168106-XX
4.1-6.9:1| 118-100115-XX| 2| M 4K15
M 4K25
3.89-5.43:1| 144-108100-XX| 2| Griffyn 4K50
4.98-7.69:1| 144-109101-XX| 1| Griffyn 4K35
6.9-10.4:1| 118-100116-XX| 2| M 4K15
M 4K25| 410 mm| 163-167105-XX
4.98-7.69:1| 144-109101-XX| 1| Griffyn 4K50
Ultra-high contrast
Lens| Part number| Lens clamp position| Projector| Lens
hood| Part number
---|---|---|---|---|---
1.95-3.26:1| 163-120103-XX| 2| Griffyn 4K50| 30 mm| 163-170109-XX
2.71-3.89:1| 163-121105-XX| 2| Griffyn 4K50| 185 mm| 163-168106-XX
3.89-5.43:1| 163-122106-XX| 2| Griffyn 4K50
Installation safety and warning guidelines
Read all safety and warning guidelines before installing the lens hood.
Warning! If not avoided, the following could result in death or serious
injury.
-
Possible hazardous optical radiation emitted from this product. (Risk group 3)
Possible hazardous optical radiation emitted from this product. (Risk group 3 under IEC 62471)
Possible hazardous optical radiation emitted from the end product. -
PERSONAL INJURY AND EQUIPMENT DAMAGE HAZARD! Make sure the loose end of the lens tether is attached to a secure structure.
Installing the lens hood
Follow these steps to install a lens hood.
- Assess if the lens clamp needs to change position (on page 1) and move the clamp, if required. The two lens clamp positions accommodate different projection lens diameters.
- Place the lens hood over the projection lens until it encounters resistance from the shoulder stop.
- Tighten the gear clamp screw to secure the lens hood over the projection lens.
- Attach the loose end of the tether to a secure structure.
Once secured, Christie recommends leaving slack in the tether.
Technical support
Technical support for Christie Enterprise products is available at:
- North and South America: +1-800-221-8025 or Support.Americas@christiedigital.com
- Europe, Middle East, and Africa: +44 (0) 1189 778111 or Support.EMEA@christiedigital.com
- Asia Pacific (support.apac@christiedigital.com):
- Australia: +61 (0)7 3624 4888 or tech-Australia@christiedigital.com
- China: +86 10 6561 0240 or tech-supportChina@christiedigital.com
- India: +91 (80) 6708 9999 or tech-India@christiedigital.com
- Japan: 81-3-3599-7481
- Singapore: +65 6877-8737 or tech-Singapore@christiedigital.com
- South Korea: +82 2 702 1601 or tech-Korea@christiedigital.com
- Christie Professional Services: +1-800-550-3061 or NOC@christiedigital.com
Installing the Enterprise Lens Hoods Instruction Sheet
020-103827-03 Rev. 1 (10-2023)
Copyright 2023 Christie Digital Systems USA, Inc. All rights reserved.
If printed, please recycle this document after use.
Documents / Resources
|
CHRISTIE Griffyn 4K50 Enterprise Lens
Hoods
[pdf] Instruction Manual
Griffyn 4K50 Enterprise Lens Hoods, Griffyn 4K50, Enterprise Lens Hoods, Lens
Hoods, Hoods
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>