Cell2 RAYZR Lighthead 3LED TIR User Manual

: June 9, 2024
: Cell2

Table of Contents

RAYZR Lighthead 3LED TIR
FIRMWARE SELECTION FOR TRAFFIC ADVISOR WARNING STICK
CUSTOM PATTERN PROGRAMMING FOR TRAFFIC ADVISOR WARNING STICK
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RAYZR Lighthead 3LED TIR
User Manual

RAYZR Lighthead 3LED TIR

WIRING FOR WARNING STICKS
RED ……………………[+] Warning Mode to +VDC with rated fuse (for correct rating, refer to the Fuse Rating Chart)
BLACK …………………to Chassis ground

Fuse Rating

2-Head Model = 2 Amps| 4-Head Model = 3 Amps

YELLOW………………. [+] Flash Pattern Selection (refer to Flash Patterns chart) / Synchronization Momentarily apply +VDC to YELLOW wire:

Once to next pattern
Quick 3 times to FP#1

Connect YELLOW wires of all sticks together for synchronization All sticks should be set to the same pattern
WHOTE …………………………..[+] for Simultaneous or Alternating Flash (for multi- sticks only)
Group1 – Sticks with WHOTE connected to +VDC will flash together
Group2 – Sticks with WHOTE not connected to +VDC will flash together
Group1 will alternate with Group2

Warning Stick Flash Patterns

1| Kit Scan| 10| [Left-Right] Single| 19| [All] Quint
2| Kit Scan + Double| 11| [Left-Right] Double 2Hz| 20| [Ali] Ultra
3| [wig-wag] Slow-Fast| 12| [Left-Right] Quint| 21| rem Single-Quad
4| [Outside-In] Single| 13| [Left-Right] Ultra| 22| [All] Single H/L
5| (Outside-In] Ultra| 14| [Left-Right] Single-Quad| 23| [All] Quint + (Left- eight] Mega
6| [Side-by-Side] Single| 15| (Left-Right] Single H/L| 24| [Half] Steady Half
7| [SIde-by-Side] Ultra| 16| [Left-Right] Quint + [All] Mega| 25| [Ali] Steady All
8| [Side-by-Side] Slow-Fast| 17| [All) Single| 26| Left Chaser
9| Random| 18| [All) Double 2Hz| 27| Right Chaser

WIRING FOR TRAFFIC ADVISOR WARNING STICK
RED ……………….. to +VDC with rated fuse (for correct rating, refer to the Fuse Rating Chart)
BLACK …………………….to Chassis ground
Fuse Rating
6-Head Model = 4 Amps
10-Head Model = 7 Amps
8-Head Model = 6 Amps

BLUE……………………. [+] Rear “Left Arrow” [122]	Rear”Centre Out Arrow” [P1]

ORANGE……………… [+] Rear “Right Arrow” [P2]

BROWN ……………. [+] Warning Mode [P3] GREEN …………….[+] Low Power Operation or [+] End-Flasher See “Firmware Selection” for End-Flasher Mode.

End Flasher Patterns ( Green )

WHITE………….. [ ] Control Panel Indicator Signal out (connect to a compatible Control Panel)
YELLOW…………….. [+] Flash Pattern Selection (refer to respective pattern chart) While End-Flasher, Traffic Advising or Warning Mode is activated, Momentarily apply +VDC to YELLOW wire:

Once to next pattern
Quick 3 times to FP#1

NOTE: [Px] = Precedence order, when more than a wire is activated at the same time, higher priority wire will affect lower priority wire. P1 being the highest priority.
End Flasher Patterns (Green) 1 Double [2Hz] (all) 2 Quad [2Hz] (all) 3 Single [2Hz] (all) 4 Double [2Hz] (split) 5 Quad [2Hz] (split) 6 Single [2Hz] (split)

Traffic Advisor Warning Stick Patterns (Brown)

1| Random / Custom| 11| [Wig-wag] Slow-Fast
2| Random Standard| 12| [Left-Right] Single
3| [Outside-In] Single| 13| [Left-Right] Ultra
4| [Outside-In] Ultra| 14| [Left-Right] Single H/L
5| [Side-by-Side] Single| 15| [Left-Right] Quint + [All] Mega
6| [Side-by-Side] Ultra| 16| [All] Single
7| [Side-by-Side] Slow-Fast| 17| [All] Double
8| Kit Scan| 18| [All] Ultra
9| Kit Scan Split| 19| [All] Quint + [Left-Right] Mega
10| Kit Scan Dual + Double| 20| [All] Steady
Arrow Patterns (Orange / Blue)

FIRMWARE SELECTION FOR TRAFFIC ADVISOR WARNING STICK

All Traffic Advisor Warning Stick come with built-in selectable firmwares. To change firmware:

Apply +VDC to RED, = and GREEN wires simultaneously then remove GREEN wire from +VDC to enter FIRMWARE selection.
Once in FIRMWARE selection mode, the unit will display one of the following patterns.
Momentarily apply GREEN wire to +VDC to change FIRMWARE. 4. Once a desired FIRMWARE is selected, save and exit by disconnect all power.

CUSTOM PATTERN PROGRAMMING FOR TRAFFIC ADVISOR WARNING STICK

PROGRAMMING FP#1 Random Custom pattern from Warning Patterns can be customized. This can only be done through firmware that is set to Traffic Arrow.
To configure FP#1 flash pattern:

Activate Warning Patterns by applying +VDC to BROWN wire.
Scroll to flash pattern FP#1 by quickly tapping +VDC 3 times to YELLOW wire .
Enter PROGRAMMING by quickly tapping +VDC 3 times to GREEN wire.
Once in PROGRAMMING, all lightheads will faintly blink once every second. The center pair of lightheads will be activated.
Tap +VDC to YELLOW wire:
• Once for next pattern (see Lighthead Pattern Chart).
• Quick 3 times for FP#1.
Scroll to the next pair of lightheads by tapping +VDC to GREEN wire.
Repeat steps 5 and 6 until all lightheads are properly configured.
Exit PROGRAMMING by quickly tapping +VDC 3 times to GREEN wire or disconnect all power.

RESETTING
To restore factory setting:

Apply +VDC to RED, YELLOW, and GREEN wires simultaneously for more than 3 seconds and remove GREEN wire from +VDC to enter FIRMWARE selection.
Once in FIRMWARE selection mode, momentarily apply GREEN wire to +VDC for more than 3 seconds to reset. All lightheads will blink once to indicate the reset.
Save and exit by disconnect all power.