cell2 SW830-2 Multi-Purpose Switch Control Panel Instruction Manual
- June 9, 2024
- Cell2
Table of Contents
SW830-2 Multi-Purpose Switch Control Panel
Instruction Manual
INSTALLATION
It is essential to install the unit properly to ensure safe and reliable operation. Please read through all instructions thoroughly and carefully before installing the unit. The correct mounting and wiring is the key to the effectiveness of SW830-2 switch. Installers must read and follow installation instructions and warnings in the manual from original manufacturer. The vehicle operator should verify this system is fastened to the vehicle securely and is functioning properly. Failure to follow all safety precautions and instructions may void warranties, cause personal injury and/or vehicle damage, including fire.
MOUNTING
Mount the power module in a location that is not exposed directly to weather
elements such as the driver compartment firewall, below the seat, or in the
trunk; and away from any air bag deployment areas. Ensure that all wiring
harness connections are made prior to connecting the harness to the power
module. Assemble the included panel stand and secure it onto a desired smooth
surface via suction cup, where it can be easily accessed by the vehicle opera-
tor. If no smooth surface is present, use the included adhesive base to assist
the mounting; ensure that the surface is cleaned thoroughly before applying
the adhesive base onto the mounting surface. Leave adhesive to set for at
least 24hr before mounting the suction cup on to the base. Once the mounting
stand is fitted, secure the control panel tightly onto the stand.
WARNING: Do not interfere with the proper operation of the vehicle airbag
deployment system.
WIRING
Use wires that are capable of handling the required current. Route the
wires properly to prevent wear, overheating and interference with air bag
deployment. Ensure that all connections are tight and double check wiring
before connecting to the vehicle battery.
SW1, SW2, SW3, SW4 : +VDC Output Connections, each connects to one
auxiliary device / relay / input up to 0.1 Amps max.
SW5, SW6, SW7 : +VDC Output Connections, each connects to one auxiliary
device / relay / input up to 0.2 Amps max.
CONTROL PANEL / FUNCTION
PROGRAMMING
Programmable Combo Button: Button B8 may be used to activate pre-programmed buttons from Button B1 to B7. To set-up pre-programmed buttons:
- Press and hold B1 and B4 for 3 seconds to enter PROGRAMMING MODE. Top Left LED Indicator x4 will light to indicate that you are in PROGRAMMING MODE.
- While in PROGRAMMING MODE, press and hold B8 for 3 seconds to start button binding.
- While Top Right LED Indicator x4 is blinking, turn ON the desired button(s) to bind with Button B8.
- Once set, press and hold B8 for 3 seconds to save the selected buttons then press and hold B1 and B4 for 3 seconds to exit PROGRAMMING MODE.
ON/OFF or Momentary Button Setting:
Button B1 to B7 may be set as an ON/OFF or a momentary activation.
- Press and hold B1 and B4 for 3 seconds to enter PROGRAMMING MODE. Top Left LED Indicator x4 will light to indicate that you are in PROGRAMMING MODE.
- While in PROGRAMMING MODE, turn ON or OFF the desired button for the following scenario:
Button B1-B7 Red Backlit| Button Mode
---|---
OFF| ON/OFF (default)
ON| Momentary - Once set, press and hold B1 and B4 for 3 seconds to exit PROGRAMMING MODE.
Mutually Exclusive Control:
Button B1-B3 or Button B1-B4 may be grouped for mutually exclusive control.
Only one of the buttons may be turned ON at a time.
- Press and hold B1 and B4 for 3 seconds to enter PROGRAMMING MODE. Top Left LED Indicator x4 will light to indicate that you are in PROGRAMMING MODE.
- While in PROGRAMMING MODE, press Button B1 or B2 for 3 seconds to turn ON/OFF its green backlit.
Green Backlit| Mutually Exclusive Group
---|---
Button B1 ON| Button B1-B3
Button B2 ON| Button B1-B4
Button B1&B2 OFF| Independent Controlled (default) - Once set, press and hold B1 and B4 for 3 seconds to exit PROGRAMMING MODE.
Note: While in mutually exclusive group, Button B2 will active all SW1, SW2 & SW3 connection together. When configuring as Mutually Exclusive Group, these buttons must be configured as “ON/OFF switch”.
European Siren Interlock:
The Button B5 and B6 may be configured so that Button B5 turns Button B6 OFF
when deactivated and turn itself ON when Button B6 is activated. This
configuration is commonly used for that Button B5 is used as the primary
visual warning device and Button B6 is use as a siren activation.
- Press and hold B1 and B4 for 3 seconds to enter PROGRAMMING MODE. Top Left LED Indicator x4 will light to indicate that you are in PROGRAMMING MODE.
- While in PROGRAMMING MODE, press Button B6 for 3 seconds to turn ON/OFF the green backlit.
Button B6 Green Backlit| Mode
---|---
OFF| Interlock OFF (default)
ON| Interlock ON - Once set, press and hold B1 and B4 for 3 seconds to exit PROGRAMMING MODE.
Note: When configuring as Button mapping mode, Button B5 and Button B6 must be configured as “ON/OFF switch”.
Button Mapping & Interlock:
Button B7 may be set to activate and deactivate by Button B5. In this setting,
Button B7 can only be turned ON/OFF when Button B5 is activated.
- Press and hold B1 and B4 for 3 seconds to enter PROGRAMMING MODE. Top Left LED Indicator x4 will light to indicate that you are in PROGRAMMING MODE.
- While in PROGRAMMING MODE, press Button B5 for 3 seconds to turn ON/OFF the green backlit.
Button B5 Green Backlit| Mode
---|---
OFF| No Button Mapping (default)
ON| Button B7 Mapped with Button B5 - Once set, press and hold B1 and B4 for 3 second to exit PROGRAMMING MODE.
Note: When configuring as Button mapping mode, Button B5 and Button B7 must be configured as an “ON/OFF Switch”.
LED Signal Display Mode Change:
The 10-LED Signal Display may display either the Lightbar flash signal or the
directional / warning advisor flash signal. To change the display mode:
- Press and hold B1 and B4 for 3 seconds to enter PROGRAMMING MODE. Top Left LED Indicator x4 will light to indicate that you are in PROGRAMMING MODE.
- While in PROGRAMMING MODE, press Button B8 to turn ON/OFF the red backlit.
Button B8 Red Backlit| Mode
---|---
OFF| Directional / warning advisor flash signal (default)
ON| Lightbar flash signal - Once set, press and hold B1 and B4 for 3 seconds to exit PROGRAMMING MODE.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>