Cell2 SRP-MS6 Stealth Registration Plate User Manual

: June 9, 2024
: Cell2

Table of Contents

SRP-MS6 Stealth Registration Plate
Tools Required (User Supplied):
INSTALLATION
**OPERATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SRP-MS6 Stealth Registration Plate
User Manual

SRP-MS6 Stealth Registration Plate

REG PLATE WARNING UNIT MANUAL
Contents:
A1 • Reg Plate Warning Unit x 1 pc
B1 • Self-Tapping Screw x 4 pcs
Application Example

The Stealth Reg Plate may be mounted at its proper position conformity to the laws and regulations issued by competent authority.

Tools Required (User Supplied):

Electric drill
Drill bit
Electric screwdriver
Screwdriver bit
Spirit level
Adhesive strips

Cell2 SRP MS6 Stealth Registration Plate - Figure 2

INSTALLATION

Proper installation of the product requires the installer to have a good understanding of automotive electronics, systems and procedures. It is essential to install the unit properly to ensure safe and reliable operation. Please read through all instructions thoroughly and carefully before installing the unit. Failure to follow these instructions could result in serious damage to the unit or vehicle and may void the warranty.
Before Installation

Remove the license plate from the vehicle and clean the reversed side and the mounting surface thoroughly.
Prepare tools and components required for installation.
Preparing License Plate
Place the Unit onto the license plate; align all four corners. Hold firmly and mark four mounting holes on the reverse side of the plate. Remove the license plate and drill four Ø5mm mounting holes from the reverse side of the license plate.
Preparing Mounting Surface
Mark the center between the license plate mounting holes on the vehicle body.
Drill one Ø10mm cut-out at the central mark.
Feed the cable through the cut-out and route it towards the control panel or switches.
Place the Unit onto the vehicle body and use a spirit level to ensure that the plate is level. Hold firmly and mark four mounting holes on the vehicle body (you may choose any four of the eight mounting holes).
Drill four Ø3.6mm~3.8mm pilot holes for later use.
Assembling License Plate onto Stealth Reg Plate
Apply adhesive strips to the reverse side of your license plate.
Align four mounting holes to the Unit, remove the back film from adhesive strips and paste the license plate onto the front of the Unit.
Assembling Stealth Reg Plate onto the Mounting Surface
Align the Unit to the mounting surface, use the supplied screws and secured the assembly onto the mounting surface.
Make wiring according to the wire function (see the reverse page).

WIRING

To Chassis Ground:
To+VDC for R65 Warning Mode
(Fuse Rating @ 3A)
For Low Power Operation
Apply +VDC to WHITE while RED wire is activated for Low Power Operation.
For Synchronization and Flash Pattern (HEAD 1)
For Synchronization and Flash Pattern (HEAD 2)| Cell2 SRP MS6 Stealth
Registration Plate - Figure 3
---|---

**OPERATION

**

For Flash Pattern Selection:
Warning mode may select and save one flash pattern. While activating the warning mode, momentarily apply GREEN (for HEAD 1) or YELLOW (for HEAD 2) wire to +VDC:

Once to next pattern.
Quick three times to FP#0. (Refer to Flash Pattern Chart)

NOTE: FP#0 is not available for flash pattern rotation.
For Simultaneous or Alternating Synchronization:

Enter SETTING MODE by powering up with RED and GREEN (for HEAD 1) or YELLOW (for HEAD 2) wires simultaneously; the lightheaded will display short flashes:
• Single flash = Group 1
• Double flash = Group 2
Remove GREEN (for HEAD 1) or YELLOW (for HEAD 2) wire from +VDC then momentarily apply to +VDC again to change Groups.
• Light heads of the same Group will flash together.
• Light heads of the different Groups will flash alternately.
Save and exit SETTING MODE by disconnecting all power.

For Synchronization:
Connect GREEN and YELLOW wire together for synchronization.
(All lightheads should be set to the same flash pattern)
NOTE: You may also connect sync wires of other compatible light heads together for synchronization.