SENA SP123 Headset User Manual

SENA SP123 Headset User Manual

Product Overview

Charging

• Red LED: Charging
• Blue LED: Fully charged

The Bluetooth / LE / Mesh function is not working while is charging.

Power On/Off

(+) Button + Center Button for 1 sec

Volume Adjustment

• (+) Button – Increase the volume
• (-) Button – Decrease the volume

Battery Check

Phone, Music Pairing

Initially Pairing the Cast The headset will automatically enter the phone pairing mode when you initially turn on the headset or in the following situation:

• Rebooting after executing Factory Reset

1. Press and hold the Center Button and (+) Button for 1 second.
2. Search for Bluetooth devices on your mobile phone. Select the Cast in the list of the devices detected on the mobile phone.
3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.

Music Operation

• Play or pause music: Press the Center Button for 1 second.
• Track back: Press the (-) Button for 1 second.
• Track forward: Press the (+) Button for 1 second.

Mobile Phone Call Making and Answering

• Answering a call: Tap the Center Button
• Ending a call: Press the Center Button for 2 seconds.
• Voice dial: Press the Center Button for 3 seconds.
• Speed  dial: Press the (+) Button for 3 seconds.
• Rejecting a call: Press the Center Button for 2 seconds.

Intercom Pairing

1. Press and hold the Center Button of two headsets for 5 seconds until red LEDs of both units start to flash rapidly.
2. Simply tap the Center Button of any one of the two headsets.

Mesh Intercom On/Off

• Mesh Intercom On : Tap the M Button.
• Mesh Intercom Off : Tap the M Button.

Radio On/Off

• Turn on the FM radio: Press the (-) Button for 1 second.
• Turn off the FM radio: Press the (-) Button for 1 second.

Ambient On/Off

Tap the Ambient Button

PPT On/Off

Tap the PPT Button

Setting

• Configuration Menu: Press the Center Button for 10 seconds.

Troubleshooting

Factory Reset

f you want to restore the headset to factory default settings, use the Factory Reset in the configuration menu. The headset automatically restores the default settings and turns off

Certification and Safety Approvals FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference byone or more of the following measures:

• Reorient or relocate the receiving antennae
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF Exposure Statement

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. When equipped, the distance between antenna and one’s head surface is 34.3 mm(worst distance).

FCC Caution
Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment.

Industry Canada(IC) Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>