RAB T34 2X4 Backlit Troffer Instructions
- June 4, 2024
- RAB
Table of Contents
© 2021 RAB LIGHTING Inc.
INSTRUCTIONS
T34® BACKLIT TROFFER 2X2, 2X4 INSTALLATION
RAB Lighting is committed to creating high-quality, affordable, well-designed
and energy-efficient LED lighting and controls that make it easy for
electricians to install and end users to save energy. We’d love to hear your
comments. Please call the Marketing Department at 888-RAB-1000 or email:
marketing@rablighting.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THE FIXTURE. RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and
all applicable local codes. Proper grounding is required for safety. THIS
PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining the
fixture. No user-serviceable parts inside.
SAFETY INSTRUCTIONS
WARNING: Risk of fire or electric shock. Suitable for damp locations.
WARNING: Suitable for 9/16” or 15/16” Flat Tee Grids in both insulated
ceilings and non-insulated ceilings. Access above the ceiling is required.
WARNING: Do not handle energized fixtures when hands are wet when
standing on wet or damp surfaces, or in water.
WARNING: The vapor barrier must be suitable for 90° C.
WARNING: Fixture to be independently supported to the building structure.
RECESSED CEILING MOUNTING
The fixture is suitable only for INDOOR RECESSED CEILING application. Above
ceiling access is required.
To mount in an insulated or non-insulated ceiling – 9/16” or 15/16” exposed
Flat Tee Grid Ceiling follow the steps below.
-
Firmly bend the pre-installed Grid Clips (up and out as shown in Fig. 1).
-
Rotate and slide the Fixture as required to fit through the Tee-Grid Bar and place it as indicated by the directional arrow as shown in Fig. 2. Secure the Fixture to the Tee-Grid Bar.
-
Support wires are required by installation codes. Support the Fixture to the building structure with Support Wires (supplied by others) through the Grid Clip Hole as shown in Fig. 3.
-
Make sure that the orientation of the Splice Box and Access Plate faces an accessible tile to make electrical splices.
-
Loosen Access Plate Screw and remove the Access Plate. Knock out appropriate Conduit Knockouts on the Access Plate to route input conduit. Use appropriate conduit connectors as required by code (Fig. 4).
-
Connect wires as shown in the wiring diagram (Fig. 5). Push all wires back into the Splice Box. Use appropriate UL-approved wire connectors as required by code to complete wiring. Be careful not to pinch wires.
WARNING: To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects. -
Replace Access Plate and tighten Access Plate Screw.
CLEANING & MAINTENANCE
CAUTION: Be surthe e fixture temperature is cool enough to touch.
Do not clean or maintain whilthe e fixture is energized.
- Clean frosted polystyrene lens & fixture with a non-abrasive cleaning solution.
- Do not open fixtures to clean the LEDs. Do not touch the LEDs.
WIRING INSTRUCTIONS
The universal voltage driver permits operation at 120V thru 277V.
- Connect the black fixture lead to the LINE supply lead.
- Connect the white fixture lead to the COMMON supply lead.
- Connect the GROUND wire from the fixture to the supply ground.
- Connect the purple fixture lead to the (V+) DIM lead.
- Connect the pink (or gray) fixture lead to the (V-) DIM lead.
NOTE: Do not connect DIM V+ (purple)/ DIM V- (pink/gray) to line voltage or supply ground.
TROUBLESHOOTING
- Check that the line voltage at fixture is correct. Refer to wiring directions.
- Is the fixture grounded properly?
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail Answered promptly –
sales@rablighting.com
Free Lighting Layouts
Answered online or by request
T34 2X2, 2X4 – 1021 73646-RAB
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>