SYNCO G3 Wireless Recording Microphone User Manual

(Microphone G3 >>> User Manual)

Thank you for choosing SYNCO product. Please read this manual carefully before use and follow all instructions mentioned herein.

Caring For Your SYNCO Product

• Please keep the product in a dry, clean, dust—free environment.

• Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage.

• Use only a soft and dry cloth for cleaning the product.

• Malfunction may be caused by dropping, impact of external force.

• Do not attempt to disassemble the product. Doing so voids warranty.

• Please have the product checked or repaired by authorized technicians
  If any malfunctions happened.

• Failure to follow all the instructions may result in mechanics damage.

• Warranty does not apply to human errors.

Package List

Product Introduction

TX Transmitter

1Volume Control Button
2 Built-In Mic
3 Switch Button
4 3.5mm Monitoring Port| 5 Recording Button
6 Pocket Clip
7 Contacts (For Charging And File Transmission)
---|---

RX Receiver

1. Switch Button/Back Button
2. Setting Button
3. Up Option Button
4. Down Option Button
5. Display Screen
6. Type C/Digital Output Port
7.  3.5mm TRS/TRRS Output
8. 3.5mm Monitoring Port
9.  Px Built-In Mic
10. Pocket Clip

TX Indicator

Working
Indicators
| Blue/green indicator on transmitter corresponds to the A/
B transmitter shown on the receiver screen
---|---
Blue/green indicator
flashes| The transmitter waiting for
connection
Blue/green indicator keeps
on| The transmitter successfully
connected to the receiver
Blue / green indicator
lights up and flashes at the
same time| Reset completed
Orange indicator on| Charging
Orange indicator off| Fully charged
Recording Indicators
| Red indicator on| Recording on
---|---|---
Red indicator off| Recording off

Basic Operations

TX Transmitter

1. Power on & Power off
   Method 1: The TX will automatically powers on when push out the TX upwards In the direction shown In the figure. When put back the transmitter, It will automatically charge and shut down when fully charged.

Method 2: Long press the switch button on the front of the transmitter for three seconds.

• The TX power on successfully when the indicator keeps blue/green, and power off when the indicator off.

• The TX automatically shuts down in 5 minutes without connection or recording.

  2. Reset
     When the TX power off, long press the switch button for 8 seconds until the indicator flashes blue-green and enters the reset state.

  3. Recording
     Long press the recording button on the TX for 3 seconds to enter or exit recording. When enter the recording mode, the red light tums on. When exit the recording mode, the red light off.

• Asingle recording audio fie lasts for a maximum of 22 hours.

  4. Monitor
     Insert the monitoring device into 3.5mm monitoring port of TX to monitor the TX Input sound. Adjust the five—level monitoring volume when press the volume button on the TX.

• This port of the TX is used as output only, not input.

RX Receiver

1. Power on /off
   Long press the switch button on the RX for 3 seconds to switch on/off.

2. Reset
   Long press the up and down buttons 8 seconds to reset the RX when LTRA+B F TRAE Tria Ud E artic | power on

3. Monitoring
   Insert the monitoring headset into the 3.5mm monitoring port of the ® Sound Effect Of Right oui Mort Output Node receiver for monitoring in real time.

Function Operations

1. Display Screen

1. Transmitter A
2. Transmitter B
3. Transmitter Signal
4. Transmitter Power
5. Transmitter Power Level
6. Sound Effect Of Left Channel
7. Gain Value Of Left Channel
8. Sound Effect Of Right Channel
9. Gain Value Of Right Channel
10. Receiver
11. Receiver Power
12. Power Level Of Receiver Microphone Power Level
13. Gain Value Of Receiver
14. Frequency Setting/Version Information
15. Output Channel Option
16. USB Port Output Gain
17. 3.5Mm Port Output Mode
18. 3.5Mm Port Output Gain
19. Monitoring Port Output Mode
20. Output Channel Option
21. Monitoring Port Volume

2. Set Panel Parameters

1. When the RX powers on, press any button to light up the screen.
2. Switch the panel with the up or down option button.
3. The selected panel will be highlighted by short pressing the Setting button(SET).
4. Short press the switch button returns to the upper level.

3. Option Information
1). TX Option (1) Set the mute switch of each TX,
(2) Check the recording storage duration of each emitter.

• Note: When the memory card is full, the icon of the TX will flash red as shown in the figure.

2). Sound Channel Option Set the sound of each channel, including:

1. Noise reduction
2. High frequency light-up
3. EQ sound effect
4. Gain adjustment of channel
   

3). RX Option

1. Set microphone of RX on/off
2. Gain microphone of RX on/off

6). Monitoring Option

1. Switch the monitoring/output mode. monitorinci.
2. Gain adjustment of

Function Setting

1. Triple-—Channel Communication

1. Take out the TX and turn it on;
2. Tum on the microphone of RX;
3. Connect the TX to the monitoring headset;
4. Connect the RX to the monitoring headset;

2. Triple—Channel output

1. When connecting the 3.5mm output port to mobile phone, select the TRRS mode in the output setting with TRRS cable. When connecting the camera, select TRS mode plug with TRS cable.
2. When connecting Type-C port to mobile phone with the Type-C cable, and switch USB mode to mobile phone mode;
3. When connecting monitoring port to the device with the TRS cable, switch the monitoring port to the output mode.

3. Output Sound Channel

4. Transfer Recording File

1. Put back the transmitter into the receiver, the contacts connected.
2. Select USB mode in the output option, and set it to read L TX memory file/read R TX memory file/data read + charging mode, according to the corresponding emitter read as needed.
3. Connect the Type—c port to the mobile phone to read the recording file in the mobile phone directly.

Specifications

TX Transmitter

WARRANTY

Warranty Period Thank you for purchasing SYNCO products.

1. Customers are entitled to free replacement or repair service in case of quality defect(s) found in the product under normal use within 30 days upon receipt of the product.
2. Original SYNCO products are entitled to 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user. Within the warranty period, if product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee).

Warranty Exclusions and Limitations

1. Faults resulted from inappropriate use of a product without following its operation specification
2. Artificial damage, e.g. crash, squeeze, scratch, or soaking
3. Modifications to a product by its user or a third party without prior written consent of SYNCO, e.g. replacement of element or circuit, label alteration
4. The code on product is inconsistent with that of warranty certificate, or the code on the product or warranty certificate is altered or torn off
5. All consumable accessory attached to a product, like cable, wind muff, battery
6. Faults as a result of force majeure, such as fire, flood, lightning, etc.

Warranty Claim Procedure

1. If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact SYNCO’s customer service through email at support@syncoaudio.com.
2. Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided.
3. If the SYNCO product is out of the warranty coverage, the service and the parts cost will be charged.

Guangzhou Zhiying Technology Co., Ltd
Room 2401, 24 / F, South Tower, Lisheng Plaza, No. 68 Huadi Avenue, Liwan District, Guangzhou, China, 510000
support@syncoaudio.com
www.syncoaudio.com
https://www.facebook.com/syncomicrophones

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>