RYOBI RACWDV40 Wet and Dry Vacuum Cleaner Owner’s Manual

RACWDV40 Wet and Dry Vacuum Cleaner

RACWDV40 Wet and Dry Vacuum Cleaner

Owner’s Operating Manual

Important! It is essential that you read the instructions in this manual before operating this machine. Subject to technical modifications.

Description
The RACWDV40 Wet and Dry Vacuum Cleaner comes with the following components:

• Telescopic Wand
• Floor tool
• Crevice tool
• Round brush
• Hose set
• Rear wheel (x2) + Hub cap (x2)
• Front caster (x2)
• Air Regulator Tube
• Handle
• Foam filter
• Wheel assembly kit
• Dust bag
• Outlet-socket for Power Take Off
• Blower connection
• Filter basket
• Safety float valve
• Cartridge filter cap
• H13 HEPA Cartridge filter
• ON/OFF switch
• Connection for the vacuum hose
• Clamp (x2)
• Tank
• Drain outlet
• Overload protection button
• Power tool adaptor
• Retaining bracket (x2)
• Filter self-cleaning button
• Air flow control button
• Power plug
• Drill suction nozzle

Refer to Fig. 1 for the components list.

Usage Instructions

Before operating the machine, please read the operating instructions carefully and completely.

• Make sure to use the machine for its designated purpose only.
  The vacuum cleaner is designed for domestic use and vacuuming up materials that are not hazardous to your health and that are not flammable.

• Do not use the machine outdoors, unless it has been specifically designed for outdoor use.

• Do not subject the machine to heat, direct sunshine or high moisture, such as rain.

• Never immerse the machine in liquids and be aware of sharp edges that may damage it. Never use the machine with wet or damp hands. Unplug it immediately if the machine becomes wet or damp when it is running. Do not immerse the machine in water.

• Wear protective clothing and gloves while using the machine.

• Connect the machine only to a 230-240V alternating current receptacle.

• Do not hold the connectors in front of your face, especially your eyes and ears. Do not direct the nozzle towards persons or animals.

Filter Self-Cleaning System

The RACWDV40 Wet and Dry Vacuum Cleaner comes with a filter self-cleaning system.

To use this system:

1. Press the filter self-cleaning button (No.27) on the machine.
2. The machine will automatically clean the filter by reversing the airflow direction.
3. Repeat this process 3-4 times for optimal cleaning.

Refer to the demonstration scan code on the machine for a visual guide on how to use the filter self-cleaning system.

General Power Tool Safety Warnings

Read and follow these safety warnings before operating the machine:

• Improper use of the machine can be harmful to people and property.
• The machine is designed solely for domestic use and for the designated purpose. It is not suitable for commercial use.
• Never use the machine for other types of use that are not designated by the manufacturer. Any other types of use are at your own risk and are possibly dangerous.
• Other uses and unattended operation are not allowed.
• The manufacturer cannot be made responsible for damages that are caused by improper use or incorrect operation.

Keep the operating instructions, the guarantee certificate, the receipt, as well as the packaging and packaging material if possible.

Important!
It is essential that you read the instructions in this manual before operating this machine.
Subject to technical modifications

DESCRIPTION

Components list

1. Telescopic Wand
2. Floor tool
3. Crevice tool
4. Round brush
5. Hose set
6. Rear wheel (x2) + Hub cap (x2)
7. Front caster (x2)
8. Air Regulator Tube
9. Handle
10. Foam filter
11. Wheel assembly kit
12. Dust bag
13. Outlet-socket for Power Take Off
14. Blower connection
15. Filter basket
16.  Safety float valve
17. Cartridge filter cap
18. H13 HEPA Cartridge filter
19. ON/OFF switch
20. Connection for the vacuum hose
21. Clamp (x2)
22. Tank
23. Drain outlet
24. Overload protection button
25. Power tool adaptor
26. Retaining bracket (x2)
27. Filter self-cleaning button
28. Air flow control button
29. Power plug
30. Drill suction nozzle

GENERAL POWER TOOL SAFETY WARNINGS

WARNING!
This appliance complies with the compulsory safety regulations for electric equipment. However, improper use can be harmful to people and property. Please read these operating instructions carefully and completely before switching the appliance on. Keep the operating instructions, the guarantee certificate, the receipt, as well as the packaging and packaging material if at all possible.

• This appliance is designed solely for domestic use and for the designated purpose. The appliance is not suitable for commercial use. Don’t use the appliance outdoors (unless it has been specifically designed for use outdoors). Don’t subject the appliance to heat, direct sunshine or very high moisture (e.g, rain).

• Never immerse the appliance in liquids and be aware of sharp edges that may damage it. Never use the appliance with wet or damp hands. Unplug it immediately if the appliance becomes wet or damp when it is running. Don’t immerse the appliance in water.

• This wet/dry vacuum cleaner may only be used and kept in a private home.

• The appliance is designed to vacuum up materials that are not hazardous to your health and that are not flammable.

• Never hold the connectors in front of your face (especially your eyes, ears, etc.). Never direct the nozzle towards persons or animals.

• Only use the appliance for its designated purpose. Any other types of use are at your own risk and are possibly dangerous.

• Other uses and unattended operation are not allowed.

• The manufacturer cannot be made responsible for damages that are caused by improper use or incorrect operation.

• Wear protective clothing and gloves.

• Connect the appliance only to a 230-240V alternating current receptacle.

• Make sure that the correct dust bag has been inserted securely in its holder before using the appliance. The wrong dust bag or incorrectly installed dust bags can cause

• damage to the appliance and cause the guarantee to become void.

• If the power cord is damaged, it must be comepletely replaced along with the cable protector by an authorised service centre or other qualified service organisation.

• Don’t vacuum up any toner dust, which is used in printers and copiers for example, because it is electrically conductive. In addition, it is possible that it will not be

• completely filtered out by the filter system of the wet/dry vacuum cleaner and can be released into the air via the exhaust fan.

• Never vacuum flammable or poisonous liquids like petrol, oil, acids, or other volatile substances.

• Don’t vacuum up liquids that are hotter than 60°C or any poisonous or flammable dusts.

• Never lay the appliance on its side. Pay particular attention to a horizontal position and adequate stability on stairs.

• Always unplug the appliance after use and before cleaning or changing the filters or accessories.

• Only trained specialists may make repairs on electric equipment. Improper repairs could result in considerable danger to the user.

• Do not store the appliance directly beside a hot oven or radiator.

• Children, disabled persons, and the aged are often not aware of the dangers that can result from handling electric appliances. The above mentioned persons and untrained persons must never work with this electrical appliance.

• When cleaning or removing the appliance, always switch it off. Pull the plug out of the receptacle, if you are not going to use the appliance for an extended period of time.

• Never pull on the cable to unplug the appliance, rather pull on the plug itself. Also, remove any special accessories from the appliance

• Always keep the appliance clean. Don’t use any solvents or cleaners that may damage or be harmful to the appliance or user.

• Never leave the appliance switched on unattended. If you leave the work area, switch the appliance off or unplug it from the receptacle (don’t pull the cord, but use the plug).

• In order to protect children from electric household appliances, make sure that the cable can’t cause children to stumble and don’t give children access to the appliance.

• Never use the appliance when you are under the influence of medication, alcohol or drugs, if you are currently under medical care, or if you are tired.

• Check the appliance and the power cord regularly for any possible damage. Don’t use damaged appliances.

• Don’t try to repair the appliance yourself. Always use an authorized technician for repairs. Always have faulty power cords replaced immediately by the manufacturer or a qualified service organization. Use the same type of cable in order to prevent any danger of electric shock and injury.

• Only use original spare parts and accessories. Non approved parts or third-party accessories may be a possible source of danger and cause the guarantee to become void.

• Check the float often.

• If you notice liquid leaking from your appliance, switch it off immediately and unplug it.

• Do not submerge the appliance in water. Make sure that water is not spilled on the appliance.

• When disposing of the wastewater, make sure that you observe any legal regulations.

• Only store the appliance in a safe and dry location outside the reach of children.

• Please also pay particular attention to the following
  “Special Safety Rules”.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• Electrical power should be supplied via a residual current device (RCD) with a tripping current of not more than 30mA.

• Only use a weather proof extension cord. Check the extension cord before every use for damage. Always uncoil the extension cord during use because coiled cords can overheat. Damaged extension cords should not be repaired, they should be replaced with an equivalent type.

• WHEN USING BLOWER FUNCTION:

  • Direct air discharge at work area only – never at people or animals.
  • Do not use blower as a sprayer in wet mode.
  • Wear a dust mask and protective eye wear.

WARNING
Always switch off and unplug the machine from the electrical outlet before assembling, opening, emptying the dirt container, before connecting/disconnecting the attachments, or carrying out maintenance or troubleshooting checks.

IMPORTANT!
If the hose or tools are blocked, switch off the cleaner and remove the blockage(s) before re-starting your machine.

IMPORTANT!
Cleaning filters and replacing them regularly maintains vacuum performance. Vax recommends that your filters should be checked, cleaned and replaced periodically.
DAMAGE TO THE VACUUM CLEANER CAUSED AS A DIRECT RESULT OF NOT ADHERING TO THE GENERAL SAFETY INFORMATION AND THE INSTRUCTIONS IN THIS USER GUIDE INVALIDATES THE WARRANTY.
PLEASE KEEP THESE INSTRUCTIONS FOR FURTHER USE.

SPECIAL SAFETY RULES

• Never vacuum up hot ashes, pointed or sharp objects. Never use the appliance in damp rooms.
• Don’t use the appliance without a dust bag (an exception is wet vacuuming or with the cartridge filter). Make sure that the dust bag is inserted into the appliance correctly.
• When using the appliance, make sure that no hair, clothing, or members are drawn in.
• Keep the vacuum cleaner away from heat sources such as radiant heaters, ovens, and so on.

DISPOSAL INFORMATION

• The appliance contains electric and electronic components and may not be disposed of as household garbage.
• The local and currently applicable legislation must be observed unconditionally.

INTENDED USE

• The wet and dry vacuum is intended to be used only by adults who have read and understood the instructions and warnings in this manual, and can be considered responsible for their actions.
• The product is intended for dry and wet vacuuming in workshop, household and similar non-industrial applications. The product can also be used for vacuuming dust and debris directly from power tools with dust ports.
• Do not use the product for any other purpose.

SPECIFICATIONS

• Model No.: RACWDV40
• Supply voltage:  220-240V ~ 50Hz
• Motor power: 1400W
• Max power take off: 1000W
• Tank capacity: 40L
• Hose system: Ø35mm
• Filter – dry: H13 HEPA Claridge filter
• Filter – wet: Foam filter
• IP rating: IPX4
• Suction: 20kpa/2.9PSI
• PTO Overload rating: 4.0A
• Cord length: 5m
• Hose length: 2.5m
• Self-Cleaning function: Yes
• Speed control function: Yes
• HEPA rating: H13
• Weight: 10.5kgs

PACKAGING CONTENT

1. Undo the clamps, lift the top section off the tank and remove the accessories from inside the tank.

ASSEMBLY

• Turn the tank upside down and insert the two caster feet into the front slots on the base. Apply downward pressure to each caster. Casters will “snap” into place when installed properly. Verify that the casters are mounted correctly.
• Insert the wheel axle into the base. Insert washer onto the axle followed by rear wheel and insert washer again. Insert the “R” locking pin into the hole on the end of the axle to lock the wheel. Snap the hub cap on to the wheel. Repeat the same steps at the other end of the axle.
• Lightly squeeze together the ends of the retaining bracket and click it into the motor housing.
• Insert the rear handle into handle guides.

ACCESSORIES FITTING

• Insert the large end of the hose into the front inlet of the tank (before this, remove the rubber pad first).
• The nozzles and brushes can install to the hose directly, or extended by the telescopic wand and air regulator tube.

OPERATION

DRY VACUUMING
WARNING
Ensure that you read, understand, and apply the safety instructions.
Reminder: DO NOT vacuum hazardous substances. The use of an incorrect dust bag will invalidate the warranty.

• Install the supplied dust bag to the inner joint and cartridge filter over the filter basket.
• Plug the power cord into the power outlet and turn the motor on by flipping switch to position and off to position when finish vacuuming, and unplug the power cord.

WARNING

• DO NOT USE THE CARTRIDGE FILTER FOR WET OR SHARP MATERIALS.
• DO NOT USE DUST BAG FOR LIQUID VACUUMING.

WET VACUUMING
WARNING
Ensure that you read, understand, and apply the safety instructions.
Reminder: DO NOT vacuum hazardous substances.

• Install the supplied foam filter over the filter basket.
• Plug the power cord into the power outlet and turn the motor on by flipping switch to position, and off to position when finish vacuumming,and unplug the power cord.
• Empty and dry the tank.

WARNING
The foam filter must be removed after wet vacuuming, and a cartridge filter must be installed before dry vacuuming again.

IMPORTANT!
When vacuuming large quantities of liquids, do not immerse the nozzle completely in the liquid; leave a gap at the tip of the nozzle opening to allow air inflow.
The machine is fitted with a float valve that stops the suction action when the container reaches its maximum capacity. You will notice an increase in the pitch of motor sound. When this happens, turn of the machine, disconnect from power supply, and drain the liquid into a suitable receptacle or drain.To continue vacuuming, refit the container with the drain cap. After wet vacuuming, turn the machine off and remove plug from power supply..
Empty the container, clean and dry the inside and outside before storage.

CONNECT ELECTRICAL APPLIANCES

• Connect electrical appliance with Power Take Off on the Vacuum, switch on electrical appliance, and flipping the switch to position. The vacuum cleaner will switch off within 3-8 seconds once the electrical appliance switches off.
• The Drill Suction Nozzle is suggested to connect to the hose and put on the wall where drilling when using an electric drill, it can vacuum up the drilling dust directly at the drill hole.

OVERLOAD PROTECTION
Overloading will activate the over current switch and cut power to the take off. Press to reset the over current switch to restore power to the take off.

FILTER SELF-CLEANING SYSTEM

• Connect to the hose which has to insert to the vacuum cleaner to make this system work.
• Insert the power plug. Move the on/off switch to the position.
• Turn the air flow speed control to the MAX position.
• Insert the air regulator nozzle into the filter self-cleaning button and press 3-4 times.
• Repeat the process two more times.

WARNING
Press the filter self-cleaning button only if the catridge filter is inserted.

BLOWER OPERATION

•  WARNING: Always wear safety goggles before using blower.

WARNING: Keep bystanders clear from blowing debris.

WARNING: Wear a dust mask if blowing creates dust that might be inhaled.

• Insert the large end of the hose into the blower connection, and fit the crevice tool to the vacuum hose.
• Turn the motor on by flipping switch to position and off to position when finish blowing, and unplug the power cord.

WARNING
If after a few seconds the hose continues to be blocked, turn off the unit and clear the hose manually.

Removing And Cleaning HEPA Dry Filter (THIS FILTER IS NOT WASHABLE)

• Unlock and remove the filter retainer by turning retainer handle anticlockwise.
• Carefully hold and pull the dry filter up for removal.
• Clean by gently tapping or brushing dirt off. For optimal performance it is recommended to regularly change this filter depending on level of use (eg. 3-6 months).

Cleaning Foam Filter

• Carefully remove foam filter.
• Use a mild soap and water solution to wash foam filter and rinse with clean water, and air dry before next use.

STORAGE

• Wind hose around the motor head and put it on the retaining bracket.
• Push the telescopic suction tube together and insert the tube holder into the accessory holder.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environmental-friendly recycling.

SYMBOL

⚠ Safety Alert
V. Volts
Hz. Hertz
∼ Alternating Current
W. Watts

Regulatory Compliance Mark (RCM).
Product meets applicable regulatory requirements.

Please read the instructions carefully before starting the machine

Recycle

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

Overload reset

Reference to the filter cleaning system

IPX4 Ingress Protection (Waterproof grade 4)

TROUBLE SHOOTING

WARNING
To reduce the risk of personal injury, unplug the cleaner before performing maintenance/troubleshooting checks.

Check Overload Protection switch. Check if switch is in position II without appliance plugged in

Functional fault in the power cord, switch, or motor| Have the damaged part checked by qualified personnel or replace it.
Tank is full of liquid| Empty the tank
Dust is blow out of the motor cover| The dust bag is missing or damaged| Put in a dust bag or replace it.
Filters are or not correctly assembled| Use missing filters or check the correct position of the filter
Low suction power and high motor speed / vibrations| Dust bag is full| Replace the dust bag
Suction nozzle, hose, or tank inlet is blocked.| Check the suction nozzle, hose, and tank inlet for obstructions.
Air control on the air regulator handle is open| Close the air control
HEPA cartidge filter is full or clogged| Follow self cleaning procedure; Clean or replace the filter

Techtronic Industries (Australia) Pty. Ltd.
31Gilby Road,
Mt. Waverley, VIC 3149, Australia

Techtronic Industries N.Z. Limited
Unit C, 70 Business Parade South, Highbrook, Auckland 2013, New Zealand

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>