RYOBI R18B 18V ONE+ Cordless Buffer Instruction Manual

: October 30, 2023
: RYOBI

Table of Contents

R18B 18V ONE+ Cordless Buffer
INTENDED USE
MAINTENANCE
ENVIRONMENTAL PROTECTION
SYMBOLS
GUARANTEE
AUTHORISED SERVICE CENTRE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

R18B
ORIGINAL INSTRUCTIONS

R18B 18V ONE+ Cordless Buffer

Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product.
Subject to technical modification

Safety, performance, and dependability have been given top priority in the design of your buffer/polisher.

INTENDED USE

The product is intended for polishing and buffing cars, boats, recreational vehicles, watercrafts, motorcycles, hardwood floors, and large furniture.
Do not use the product in any way other than those stated for intended use.

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.

MAINTENANCE

When servicing, use only original manufacturer’s replacement parts. Use of any other parts may create a hazard or cause product damage.
Do not use compressed air to blow dust/dirt from any power tool. Serious eye injury could result. Use a cloth, brush or vacuum to remove dust and dirt.
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
Do not attempt to modify this tool or create accessories not recommended for use with this tool.
For greater safety and reliability, all repairs should be performed by an Authorised Ryobi Service Centre.

APPLICATION AND BUFFING/POLISHING BONNETS

Both the application and buffing/polishing bonnets are reusable. For maximum life and performance, hand wash after use and allow them to air dry. If needed, the bonnets can be machine washed in cold water with a small amount of detergent, then machine dried using low heat.

FOAM PAD

It is important that the pad retain its original shape and dimensions. Allow it to dry completely after each use. Make sure to remove the bonnets, wash them, and store separately. The product should be stored with the pad facing up in order to extend pad life and retain its shape. Be careful not to use too much polish at one time. If the pad becomes saturated, it will not last as long.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environmental-friendly recycling.

SYMBOLS

| Safety alert
---|---
| No-load speed
| Diameter
| CE conformity
| EurAsian Conformity Mark
| Please read the instructions carefully before starting the machine.
| Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.

RYOBI R18B 18V ONE Cordless Buffer - Product Overview
1 RYOBI R18B 18V ONE
Cordless Buffer - Product Overview 3

Product specifications
Buffer/Polisher
Voltage
No-load speed
Buffing pad size
Orbital diameter
Weight – according to EPTA Procedure 01/2003
Weight – excluding battery pack

Battery and charger
Compatible battery pack (not included)
Lithium-Ion
Compatible charger (not included)
Lithium-Ion

WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

GUARANTEE

In addition to any statutory rights resulting from the purchase, this product is covered by a guarantee as stated below.

The guarantee period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The roduct is designed and dedicated to consumer and private use only. So there is no guarantee provided in case of professional or commercial use.
There is, in some cases (i.e. promotion, range of tools), a possibility to extend the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of the tool is clearly displayed in stores and/or on packaging. The end user needs to register his/her newly-acquired tools online within 8 days from the date of purchase. The end user may register for the extended warranty in his country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of the data which are required to enter online and they have to accept the by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty. Your statutory rights remain unaffected.
The guarantee covers all defects of the product during the warranty period due to defaults in workmanship or material at the purchase date. The guarantee is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or being incorrectly connected. This guarantee does not apply to:
• any damage to the product that is the result of improper maintenance
• any product that has been altered or modified
• any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
• any damage caused by non-observance of the instruction manual
• any non CE product
• any product which has been attempted to be repaired by an nonqualified professional or without prior authorization by Techtronic Industries
• any product connected to improper power supply (amps, voltage, frequency)
• any damage caused by external influences (chemical, physical, shocks) or foreign substances
• normal wear and tear of spare parts
• inappropriate use, overloading of the tool
• use of non-approved accessories or parts
• carburettor after 6 months, carburettor adjustments after 6 months
• power tool accessories provided with tool or purchased separately.
Such exclusions include but is not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide
• components (parts and accessories) subject to natural wear and tear, including but not limited to carbon brushes, chuck, power cord, auxiliary handle, sanding plate, dust bag, dust exhaust tube
For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
A repair/replacement under this guarantee is free of charge. It does not constitute an extension or a new start of the guarantee period. Exchanged parts or tools become our property. In some countries delivery charges or postage will have to be paid by the sender.
This guarantee is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.

AUTHORISED SERVICE CENTRE

To find an authorized service center near you. visit http://uk.ryobitools.eu/header/service-and-support/service-agents.

EC declaration of conformity
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Herewith we declare that the product
18V Buffer/Polisher
Brand: Ryobi
Model number: R18B
Serial number range: 44444001000001 – 44444001999999 is in conformity with the following European Directives and harmonised standards 2011/65/EU, 2006/42/EC, 2004/108/EC(until 19 Apr. 2016), 2014/30/EU,
EN 60745-1:2009+A11:2010, EN60745-2-4:2009+A11:2011,
EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:1997+A1:2001+A2:2008
RoHS documentation is compiled according to EN 50581:2012

Andrew John Eyre (BEng, CEng, MIET)
Vice President, Regulatory & Safety
Winnenden, May. 15, 2015
Authorised to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany

Techtronic Industries GmbH
Max-Eyth-Straße 10,
71364 Winnenden, Germany