reolink RLC-510WA HD Wireless WiFi Smart Camera User Guide
- June 9, 2024
- reolink
Table of Contents
reolink RLC-510WA HD Wireless WiFi Smart Camera
What’s in the Box
NOTE: Camera and accessories vary with different camera
models that you purchase.
Camera Introduction
Connection Diagram
Before initial setup, follow the steps below to connect your camera.
- Connect the camera to a LAN port on your router with an Ethernet cable.
- Power on the camera with a power adapter.
Set up the Camera
Download and Launch the Reolink App or Client software, and follow the onscreen instructions to finish initial setup.
-
On Smartphone
Scan to download the Reolink App. -
On PC
Download path of the Reolink Client: Go to https://reolink.com >Support > App & Client.
Install the Camera
Installation Tips
- Do not face the camera towards any light sources.
- Do not point the camera towards a glass window. Or, it may result in poor image performance because of the window glare by infrared LEDs, ambient lights or status lights.
- Do not place the camera in a shaded area and point it towards a well-lit area. Or, it may result in poor image performance. For better image quality, please make sure that the lighting condition for both the camera and the capture object is the same.
- For better image quality, it’s recommended to clean the lens with a soft cloth from time to time.
- Make sure the power ports are not exposed to water or moisture or blocked by dirt or other elements.
- Do not install the camera at places where rain and snow may hit the directly.
- The camera may work in extreme cold conditions as low as -25°C.
Because when it is powered on, the camera will produce heat. You may power on the camera indoors for a few minutes before installing it
outdoors.
NOTE: There are two different types of mounts for bullet cameras. Please
check out the mount included in the package and follow the
corresponding instruction to install the camera properly.
Mount the Camera
Drill holes in accordance with the mounting hole template.
NOTE: Use the drywall anchors included in the package if needed.
Install the mount base with the mounting screws included in the package.
NOTE: Run the cable through the cable notch on the mount base.
To get the best field of view, loosen the adjustment knob on security mount and
turn the camera. 
Stiffen the adjustment knob to lock the camera.
NOTE: If your camera has another mount without the adjusting knob, please loosen the adjusting screw with the provided hex key and turn the camera as shown below to adjust the angle.
Twist the screws with the wrench to unlock the camera and adjust its
direction. 
After adjustment, twist the screws back to lock the camera.
Troubleshooting
IP Camera Is Not Powering on
If you find your camera is not powering on, try the following solutions:
- Please check whether the outlet is working properly or not. Try to plug the camera into a different outlet and see if it works.
- Please check whether the DC adapter is working or not. If you have another 12V DC power adapter which is working, please use another power adapter and see if it works.
If these won’t work, please contact Reolink Support https://support.reolink.com
IR LEDs Stop Working
If you find the IR LEDs of your camera stop working, try the following
solutions:
- Go to Device Settings and check whether you have enabled Infrared LEDs. If the LEDs are disabled, please enable them.
- Please go to Live View and check the Day/Night mode. Set the mode to Auto to activate the IR lights.
- Upgrade your camera’s firmware to the latest version.
- Restore the camera to the factory settings and check the IR light settings again.
If these won’t work, please contact Reolink Support https://support.reolink.com
Specifications
Hardware Features
IR Distance: 30 meters (100ft)
Day/Night Mode: Auto switchover
General
- Operating Temperature: -10°C to 55°C (14°F to 131°F)
- Operating Humidity: 10%-90%
- Weather Resistance: IP66 certified weatherproof
Notification of Compliance
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC RF Exposure Warning Statements
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment shall be installed and operated
with minimum distance 20cm between the radiator & body.
Simplified EU Declaration of Conformity
Reolink declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
Correct Disposal of This Product
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm
to the environment or human health from uncontrolled waste disposal, recycle
it responsibly to promote the sustainable reuse of material resources. To
return your used device, please use the return and collection systems or
contact the retailer where the product was purchased. They can take this
product for environmentally safe recycling.
Limited Warranty
This product comes with a 2-year limited warranty that is valid only if purchased from Reolink official stores or Reolink authorized resellers. Learn more: https://reolink.com/warranty-and-return/.
NOTE: We hope that you enjoy the new purchase. But if you are not satisfied with the product and plan to return, we strongly suggest that you reset the camera to factory default settings and take out the inserted SD card before returning.
Terms and Privacy
Use of the product is subject to your agreement to the Terms of Service and
Privacy Policy at reolink.com. Keep out of the reach of children.
End User License Agreement
By using the Product Software that is embedded on the Reolink product, you
agree to the terms of this End User License Agreement (“EULA”) between you and
Reolink. Learn more: https://reolink.com/eula/.
ISED Statements
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radio Frequency Exposure Statement for IC
The device has been evaluated to meet general RF exposure requirements. The
device can be used in mobile exposure conditions. The min separation distance
is 20cm.
Operation of this device is restricted to indoor use only. (5180-5240MHz)
This radio transmitter [IC: 26839-2204C] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Antenna Lists
External Antenna YJC-60302-W27 3dBi 2400-2500MHz
External Antenna YJC-60302-W27 3dBi 5150-5850MHz
Technical Support
If you need any technical help, please visit our official support site and
contact our support team before returning the products,
https://support.reolink.com
- For USA: The frequency stability of all transmission frequencies of U-NII-1, U-NII 2A, U-NII 2C and U-NII-3 meets the requirements of 47 CFR FCC Part15.407(g), and the manufacturer declares that their transmission is maintained at Band U-NII- 1, U-NII 2A, U-NII 2C and U-NII-3.
- For Canada: The frequency stability of all transmission frequencies of U-NII-1, U-NII 2A, U-NII 2C and U-NII-3 meets the 47 CFR FCC Part15.407(g) requirements, and the manufacturer states that their transmissions remain within the U-NII-1, U-NII 2A, U-NII 2C and U-NII-3 bands.
References
- Reolink Official: Security Cameras and Systems for Home & Business
- Reolink Official: Security Cameras and Systems for Home & Business
- Warranty & Return – Reolink
- Reolink Support - Official Reolink Help Center
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>