marta MT – 4267 Electric Oven User Manual

: June 9, 2024
: MARTA

Table of Contents

marta MT – 4267 Electric Oven
Parts list
USING THE APPLIANCE
HEATING MODE SELECTION
USING THE ROTISSERIE
USING THE SKEWER
CLEANING AND MAINTENANCE
SPECIFICATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

marta MT – 4267 Electric Oven

Parts list

marta-MT-4267-Electric-Oven-FIG-8

Housing
Door with handle
Temperature control knob
Operation indicator light
Heating mode selection knob
Convection/rotisserie switch-on knob
Timer setting knob
Rotisserie and handle for removing
Bake tray
Wire rack
BBQ forks
Handle for removing the bake tray / Wire rack

CAUTION: Read this manual carefully before using the appliance and save it for future reference. When using electrical appliances, basic precautions should always be followed, including the following:

The appliance is designed for domestic cooking and heating only in accordance with these operating instructions.
Before the first use, check the device specifications and the power supply in your network. Use the appliance only on the voltage specified on the identification plate.
The device must always be connected to a grounded socket.
It is not intended for industrial use.
Use the device in a well ventilated room with at least 15 cm. space on each side for normal air circulation and heat removal.
Do not allow the operating device to come into contact with fusible or flammable materials, fabrics, curtains, etc.
For indoor use only. Use only for domestic purposes according to the instruction manual. Do not use or store the unit in damp and moist areas where it may come in contact with water.
Do not place or use the unit on or near other household appliances (a hot gas or electric burner, etc.)
The appliance is designed for domestic cooking and heating only in accordance with these operating instructions.
Before the first use, check the device specifications and the power supply in your network. Use the appliance only on the voltage specified on the identification plate.
The device must always be connected to a grounded socket.
It is not intended for industrial use.
Use the device in a well ventilated room with at least 15 cm. space on each side for normal air circulation and heat removal.
Do not allow the operating device to come into contact with fusible or flammable materials, fabrics, curtains, etc.
For indoor use only. Use only for domestic purposes according to the instruction manual. Do not use or store the unit in damp and moist areas where it may come in contact with water.
Do not place or use the unit on or near other household appliances (a hot gas or electric burner, etc.)

BEFORE THE FIRST USE

Unpack the appliance and remove all packaging materials and labels. Store warning labels (if available) and the product serial number plate on the housing!
Clean the device with a damp cloth, clean the accessories in soapy water rinse thoroughly and dry.
Make sure that there are no packaging materials or foreign objects (including products) inside.
Switch on all heating elements by selecting heating mode this is normal and not a malfunction. At the end of this cleaning procedure, let the unit cool down, after which it will be ready for operation.

USING THE APPLIANCE

SWITCHING ON

Make sure the device is switched off (timer adjustment knob is in the «OFF/0» position). Connect the device to the power supply.
Install a bake tray and/or wire rack, place the food. If the food is cooked on the wire rack/skewer/rotisserie, place the bake tray on the bottom level to prevent oil/grease/juice droplets from getting onto the heated surfaces.
Turn the temperature adjustment knob “3” to set the desired temperature from 100 to 250°C.
Then turn the heating mode selection knob “5” to set desired heating mode.
If you need to additionally enable the convection mode, or rotation of skewer/rotisserie, or both modes together, turn the knob “6 ” to the desired position.
To turn on the device, set the timer from 1 to 60 minutes by turning the timer setting knob “7”.
The inner light and indicator light “4” will illuminate, the device starts working.
After the set time has elapsed, an audible signal will sound, the inner light & indicator light will go out, and the device will stop working.

If the products are not ready yet, set the additional operating time by turning the timer knob.
In order to get better cooking performance, it is recommended to pre-heat the oven about 10-15 minutes. DO NOT USE THE APPLIANCE MORE THAN 4 HOURS WITHOUT A BREAK.

HEATING MODE SELECTION

To set the desired heating mode, turn the heating mode adjustment knob “5” to one of the following positions:

the upper heating elements operating mode.
the upper & lower heating elements operating mode.
the lower heating elements operating mode.
all heating elements & operating modes are off.

SWITCHING ON CONVECTION MODE AND ROTATION OF THE SKEWER/ROTISSERIE To turn on the convection mode or the rotation of the skewer/rotisserie, or both modes together, turn the knob “3” to one of the following positions:

convection mode.
convection mode & rotation of the skewer/rotisserie.
rotation of the skewer/rotisserie.
convection mode & rotation of the skewer/rotisserie are off.

USING THE ROTISSERIE

Loosen the clamps on the retainers.
Attach one retainer to the rod of the rotisserie, insert the rod through the product you are going to cook, place the food in the center of the rotisserie, and attach the second retainer. Make sure that the clamps are twisted and the impaled product is firmly fixed on the rotisserie. Do not allow the product parts to come into contact with the heating elements!
Set the rotisserie with the right end in the drive hole in the center of the right wall inside the chamber, and the end with the cap in the slot holder located on the left wall of the chamber.
Set the desired temperature, then choose desired cooking modes by turning the knobs “5” & “6” and set the timer.
To avoid burns, use the supplied handle “8” and gloves (not included) to install and remove the skewer or the rotisserie.
To remove the skewer or the rotisserie, first lift the left side of the skewer so that it comes out of the slot holder, then remove the right side.

USING THE SKEWER

Loosen the clamps on the retainers.
Thread the rod through the square holes in the skewer (parallel to the shapruram).
Tighten the clamps.
Skewer the product you are going to cook.
Set the skewer with the right end in the drive hole in the center of the right wall inside the chamber, and the end with the cap in the slot holder located on the left wall of the chamber.
Set the desired temperature, then choose desired cooking modes by turning the knobs “5” & “6” and set the timer.
To avoid burns, use the supplied handle “8” and gloves (not included) to install and remove the skewer or the rotisserie.
To remove the skewer or the rotisserie, first lift the left side of the skewer so that it comes out of the slot holder, then remove the right side.

SWITCHING OFF

The device will automatically turn off when the time set on the timer expires.
The device can be switched off at any time by turning the heating mode adjustment, temperature adjustment and timer knobs to the “OFF” position. An audible signal will sound, the light indicator will go out, the device will stop working.
WARNING: Always turn off the unit when cooking is finished.
Disconnect the appliance from the power supply. Do not pull on the wire, only hold on to the plug. Always allow the appliance to cool down completely before you put it away.

CLEANING AND MAINTENANCE

Before cleaning, always unplug the appliance.
Use wet cloth to clean the device. Do not immerse the appliance in water or other liquids.
Clean accessories in soapy water and dry.
Do not use chemical and abrasive cleaners for cleaning.
Recommended to clean the device right after operating.

SPECIFICATION

COSMOS FAR VIEW INTERNATIONAL LIMITED

Room 701, 16 apt, Lane 165, Rainbow North Street , Ningbo, China Made in China

---|---|---|---|---|---
230 V ~ 50 Hz| 2400| 40| 8,0 / 9,3| 564 х 390 х 416

WARRANTY DOES NOT COVER SUPPLIES (filters, ceramic and non-stick coating, rubber seals, etc.)
Production date is available in the serial number located on the identification sticker on the gift box and/or on sticker on the device. The serial number consists of 13 characters, the 4th and 5th characters indicate the month, the 6th and 7th indicate the year of device production. Producer may change the complete set, appearance, country of manufacture, warranty and technical characteristics of the model without notice. Please check when purchasing device. Current information about service centers is available on the website http://multimarta.com/