SUPERATV Polaris Ranger Speeddoctor Speedometer Correction Kit Instruction Manual
- June 9, 2024
- SUPERATV
Table of Contents
Polaris Ranger Speeddoctor Speedometer Correction Kit
Instruction Manual
Need help with your installation?
sales@superatv.com
1-855-743-3427
www.superatv.com
8:00am – 8:00pm EST M-Th
8:00am – 7:00pm EST Friday
9:00am – 2:00pm EST Saturday
Liability Statement
SuperATV’sE products are designed to best fit user’s AN/UN under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by SuperATVE and is not recommended.
SuperATV’ss products could interfere with other aftermarket accessories. If
user has aftermarket products on machine, contact SuperATVE to verify that
they will work together.
Although SuperATVE has thousands of satisfied customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc. will
change the ride of machine and may increase maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs
increases risk of bodily harm or death. No warranty or representation is made
as to this product’s ability to protect user from severe injury or death.
SuperATVE urges operators and occupants to wear a helmet and appropriate
riding gear at all times.
By purchasing and installing SuperATVe products, user agrees that should
damages occur, SuperATVr will not be held responsible for loss of time, use,
labor fees, replacement parts, or freight charges. SuperATVe, nor any 3rd
party, will not be held responsible for any direct, indirect, incidental,
special, or consequential damages that result from any product purchased from
SuperATVr. The total liability of seller to user for all damages, losses, and
causes of action, if any, shall not exceed the total purchase price paid for
the product that gave rise to the claim.
SuperATVE will warranty only parts provided by SuperATVE. Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered by SuperATVe. SuperATVs parts and products are not
warrantied if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your AN/UN may violate certain local, state, and federal laws. Be
advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation
law. The Buyer is solely and exclusively legally and personally responsible
for any violation of the law by the installation or use of the product. You
must abide by all local, state, and federal laws, including but not limited to
vehicle safety, traffic laws, and ordinances. It is your responsibility to
know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of
his/her vehicle according to manufacturer specifications, warnings and
instructions and agrees to hold SuperATV harmless from any damage resulting
from failure to adhere to such specifications, warnings and/ or instructions.
The Buyer is also responsible to obey all applicable federal, state, and local
laws and ordinances when operating his/her vehicle while using this product,
and the Buyer agrees to hold SuperATVe harmless from any violation thereof.
Notes:
- Do not discard packaging until product has been successfully installed.
- Controller mounting locations shown are SuperATV’s recommendation; user may secure in a different location.
- Verify that Harness will reach Controllers final mounting location.
- When routing Harness, use provided Wire-Ties and secure away from rotating and/or hot parts.
Follow steps before installing Speed Calibrator:
Failure to have a passenger assist during this process could result in injury
or contribute to an accident.
-
Have a passenger open any GPS speed app on a phone.
-
Drive machine at 30MPH on Speedometer.
-
Have passenger note actual ground speed displayed via GPS speed app.
-
Park and turn off machine.
Install Speed Calibrator Kit: -
Connect Harness to Differential Connection; see following pages for machine specific location.
-
Secure Controller, route Harness to Controller and connect.
-
Turn key on to power up Controller.
-
Hold any button down for 5 seconds. Display will flash once.
-
Default value is 30.0. Use buttons to change value to previously noted GPS speed app.
Repeat steps 1-3 to verify that Speedometer and GPS speed app values match.
Correct if necessary.
Polaris RZR XP’s
Honda Talon’s
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>