LITHONIA LIGHTING L2XLED 3 Inch Led New Construction Housing Instruction Manual
- June 9, 2024
- LITHONIA LIGHTING
Table of Contents
LITHONIA LIGHTING L2XLED 3 Inch Led New Construction Housing Instruction
Manual
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
For your protection, read carefully before proceeding with installation. To be installed by a qualified electrician. Heavy duty gloves should be worn to protect hands from sharp edges. Protective eye wear should be worn to prevent injury to eyes.
- Electric current can cause painful shock, serious injury, or death. For your safety, always remember the following:
- Turn off the power supply.
- Ground the fixture to avoid potential electrical shocks.
- Do not handle an energized fixture.
- Check all electrical connections to be sure they are tight and correct.
- Specific safety information concerning lamps.
- Match wattage of fixture and lamp exactly.
- Do not remove or insert lamp when power is on.
- Do not scratch glass or subject lamp to undue pressure as either may cause lamp breakage.
- Protect operating lamp from direct contact with water.
- Make sure appropriate trim and rough-in are used. Match labels on both fixture and trim.
- Install and wire fixtures per all applicable national and local electrical codes.
- All fixtures listed above are rated for use in 120V, 60 hz protected circuit and 90°C rated supply wire.
- This product may be installed in either type IC or Non-IC applications. A
CAUTION: RISK OF FIRE
Most dwellings built before 1985 have supply wire rated 60°c. Consult a
qualified electrician before installation.
Mount per all national and local codes.
NOTICE: “If lamp is marked Hg it contains mercury. Follow disposal laws.” See www.lamprecycle.org
Make certain that all power is disconnected prior to installing the fixture. Make all necessary wiring corrections, observing proper voltage and polarity. Ensure that wires are not being pinched.
INSTALLATION
-
The rough-in can be installed in either wood joist or suspended ceilings.
Wood Joist Installation: Extend the bar hangers to fit between the joist. Using the built in leveler (See Figure 1) , line fixture up with bottom of wood joist. Using a hammer, secure the housing to the wood joist with the built in step nail.
Suspended Ceiling Installation: Locate the four (4) T-bar slots near the end of the bar hanger (See Figure 2). Bend tabs out, slip the hanger bar over the T-bar and press the tabs back against the T-bar to hold it in place (See Figure 2).
-
Make certain all power is disconnected prior to installing the fixture. Open the snap-on junction box captive door and remove the appropriate pry-out with screwdriver. Built in Romex clamps are accessible through the Romex pry-outs (See Figure 3). Bring supply wires into box by shielded cable or Romex cable.
-
Make all connections inside the junction box. Connect 120V hot wire to the black wire. Connect the neutral wire to the white wire. Connect the ground wire to the bare copper wire. This fixture should be wired in accordance with the NEC and applicable local codes and ordinances.
-
Close the snap-on junction box door.
-
This unit can be installed in a TYPE IC or TYPE NON-IC installation:
TYPE IC: Where the rough-in section is in direct contact with insulation. Match trims listed on IC portion of the fixture label for IC installations. Remove the peel off label on top of the housing stating not to install insulation within 3 inches (76mm) of any side of the fixture (See Figure 4)
TYPE NON-IC: Where no insulation is placed over the top or within 3 inches (76mm) of the sides of the rough-in section. Match trims listed on the NON-IC portion of the fixture label for NON-IC installations. -
This product is Air Tight and conforms to maximum air leak rate of less than 2.0 CFM as tested per ASTM E-283 method. Product must be sealed to ceiling surface to eliminate all air paths into space above. The gap between the drywall edge and the edge of the recessed fixture must be sealed by the installer using drywall compound (not provided) or silicone caulking (not provided) rated for a minimum of 90 degree C to seal the gap.
TRIM INSTALLATION
SEE TRIM INSTRUCTION SHEET FOR DETAILS
LAMP INSTALLATION
Prior to installing lamp (not included) in the fixture, check to make sure that all power is disconnected. Figure 4 Ensure that the lamp source and wattage corresponds with the fixture label and the trim label. To properly seat the lamp into the fixture, screw the lamp securely into the socket. Back the lamp out one to two turns, and then screw the lamp back into the socket, making sure that it is secure.
Follow lamp manufacturer’s instructions regarding lamp operation and re- lamping. Operating a fixture with a lamp that turns on and off, an extinguished lamp, or no lamp at all may cause damage to the components and will void all warranties.
L7XF RECF ONLY —TWO (2) YEAR LIMITED WARRANTY Lithonia Lighting, a
division of Acuity Lighting Group, Inc., warrants to the original consumer,
purchaser, or user of this product that this product shall be free from
defects in materials and workmanship, under normal use and conditions, for a
period of two (2) years from the date of purchase. If this product fails to
conform to the foregoing warranty at any time within such two (2) year period,
you should contact the Lithonia Technical Support Center at the number listed
below for a return authorization and shipping instructions. Upon receipt of a
defective product covered by this warranty, Lithonia will at its option and as
your sole remedy, repair or replace this product with Lithonia’s then current
version of such product. This warranty does not apply to damage or failure
caused by or resulting from (a) accident, neglect, abuse, or acts of God
(including lightning); (b) unauthorized repair or modification of the product;
(c) failure to install or use the product in accordance with the instructions
therefore or national or local building codes, or use of the product other
than for its intended purposes; (d) use of the product with any attachments
not provided by Lithonia; or (e) use of the product in a commercial service.
EXCEPT AS EXPRESSLY PROVIDED IN THIS WARRANTY, LITHONIA MAKES NO WARRANTIES OF
ANY KIND WITH RESPECT TO THIS PRODUCT, AND ALL IMPLIED WARRANTIES THAT MAY BE
APPLICABLE TO THIS PRODUCT, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF
MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
LIMITED TO THE TWO (2) YEAR DURATION OF THIS LIMITED WARRANTY. Lithonia’s
total liability arising in any manner in connection with this product shall be
limited to the amount of the purchase price and in no event shall Lithonia be
liable for any incidental, consequential, special, or indirect damages,
including, without limitation, loss of time, inconvenience, or loss of use of
this product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, or allow limitations on how long an
implied warranty lasts, so the above limitations or exclusions may not
directly apply to you or your situation.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Lithonia Lighting
Downlighting One Lithonia Way / Conyers, GA 30012
800-315-4935 /
www.lithonia.com
Part Number: CJ520106 RevG.
©2016 Acuity Brands Lighting, Inc., 1 1 /16
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>