SIGURO SGR-HD-G230S Cooker Hood Instruction Manual

June 9, 2024
SIGURO

SIGURO SGR-HD-G230S Cooker Hood Instruction Manual
SIGURO SGR-HD-G230S Cooker Hood

SAFETY INFORMATION

  1. This appliance is intended for use by children 8 years of age and older and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, provided they have been given supervision or instruction concerning use of the appliance in a safe manner and understand the potential hazards.
  2. Children must not play with the device.
  3. Cleaning and user maintenance must not be performed by children without supervision.
  4. If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a dangerous situation.
  5. Provide adequate room ventilation if the range hood is used at the same time as appliances burning gas or other fuels, except for appliances that only blow air back into the room.
  6. Carry out the method and frequency of cleaning according to the instructions in the “Cleaning and maintenance” chapter. Follow all instructions in this manual.
  7. WARNING: There is a risk of fire if cleaning is not carried out according to the instructions.
  8. It is forbidden to flambé or use an open flame under the hood.
  9. WARNING: When using cooking appliances, accessible parts can become hot. Take extra care. There is a risk of serious burns and injury if used incorrectly.
  10. The extracted air must not be vented into a chimney used to exhaust fumes from appliances burning gas or other fuels, with the exception of appliances that only discharge air back into the room.
  11. The minimum distance between the surface of the hob and the lowest part of the hood is 65 cm.
  12. Follow the regulations regarding venting the extracted air.
  13. This range hood is only intended for installation above a hob with a maximum of four cooking zones.
  14. Follow the installation instructions in this manual.
  15. Use the supplied mounting kit or a kit recommended by the manufacturer to attach the range hood.
  16. WARNING: Incorrect installation of screws or attached devices specified in the instructions may result in an electrical hazard.
  17. The range hood is designed to extract steam and vapors during cooking in the home. Do not use it in a commercial establishment. Do not use it for purposes other than those for which it is intended.
  18. Before connecting the plug of the power cord to the mains socket, make sure that the voltage on the rating plate corresponds to the voltage in your socket.
  19. Connect this range hood only to a properly grounded outlet. Do not use extension cords, portable extension sockets, adapters or other similar devices.
  20. Switch off the hood and disconnect the power supply plug whenever you clean it, change the lighting, assemble or disassemble it.
  21. When replacing lighting, always use the same type of fluorescent light specified by the manufacturer.
  22. This range hood cannot be used as a support surface.
  23. If the hood is damaged, contact an authorized service center to have it repaired. Never repair it yourself. There is a risk of injury from electric shock

Lighting specifications
Type of fluorescent light: 2 × L11C
Shape: round
Rated power: 2 W

Overview

OVERVIEW

  1. The outer shell of the chimney
  2. The outer shell of the hood
  3. Control panel
  4. Grease filters
  5. Lighting (placed in the back)

Not shown

  • Motor unit
  • Carbon filters (2 pcs)
  • Non-return valve

Control panel

  1. Range hood switch off button
  2. Speed button 1 (low speed)
  3. Speed button 2 (medium speed)
  4. Speed button 3 (high speed)
  5. Light on/off button

TECHNICAL PARAMETERS

Power 220–240 V~, 50 Hz
Power consumption 200 W
Dimensions 480 × 261 × 595 mm
Weight 8.3 kg
Motor type E-750 m3/h; 200 W
Suction pipe diameter 150 mm

INSTALLATION

WARNING:
Incorrect installation of screws or attached devices specified in the instructions may result in an electrical hazard.

Warning:
Make sure the hood is turned off and disconnected from the power source prior to installation.

Supplied mounting kit:
9× screws St 4×30
9× dowels Ø5 × Ø8
2× screws St 3×10
1× cooker hood holder
2× chimney holder

Plan
Plan

Installation instructions
The minimum distance between the surface of the hob and the lowest part of the hood is 65 cm. The recommended distance is 70 cm. The range hood is designed both for extraction into the chimney and for air recirculation.

Chimney flue
The fumes are vented out of the building using a suction pipe that is connected to a non-return valve at the top of the hood. The diameter of the suction pipe must match the diameter of the non-return valve. The suction pipe is not included in the package. If the range hood has been used with a carbon filter, it must be removed if it is to be used again with a chimney flue.

Recirculation
During recirculation, air is discharged back into the room. The intake air is degreased and deodorized, and is then discharged back into the room. Before using the hood in this way, you have to install carbon filters.

Installation

  1. Place the holder against the wall and mark the holes (3 x 8 mm) which you drill with a drill. Insert dowels into the holes, attach the holder and secure with screws. Make sure they are well tightened.

  2. Place the hood on the holder and mark the places to drill two holes (from the inside of the hood). Carefully remove the hood from the holder.

  3. Drill holes (8 mm). Insert the dowels in them.

  4. Carefully lift the hood and insert it on the holder.

  5. Secure the hood from the inside with two screws

  6. Depending on the height of the chimney part, drill 2 x 2 holes according to the holders supplied. Insert dowels into the holes, attach the holders and secure with screws. The longer holder is for the upper chimney part.

  7. Insert the non-return valve on the outlet opening in the upper part of the hood.

  8. Attach the end of the suction pipe to the nonreturn valve in the upper part of the range hood

  9. Insert the upper chimney part on the lower chimney part. Then pull the upper chimney part to the desired height.

  10. Hang the upper part of the chimney on the holder. There are two securing methods:
    using locks on both sides (see Fig. 1 on the left),
    using screws (3x 10 mm) on both sides (see Fig. 2 on the left).

  11. Chimney flue Attach the other end of the suction pipe to the flange in the wall. It must have a diameter corresponding to the suction pipe. A smaller diameter can cause lower suction performance and higher noise when using the range hood. Do not bend the suction pipe excessively. The maximum bending angle is 90°. To ensure efficient suction performance, we recommend bending the suction pipe only once.

Electrical wiring

Before plugging the range hood into the mains socket, make sure that the voltage indicated on its rating plate matches the voltage in your mains socket. If in doubt, contact your electricity supplier. If the socket needs to be modified, always contact a qualified electrician. The electrical wiring must be carried out in accordance with the valid regulations and directives in force in the country of installation. The range hood is equipped with an electrical plug, which you plug into a properly grounded electrical outlet after installation. We recommend that the electrical socket to which the range hood will be connected be placed in a separate circuit with its own circuit breaker.

USE

Before first use
Wipe the outside of the appliance with a soft sponge slightly moistened with warm water. Insertion of carbon filters

Note:
Do this step if you are using the recirculation method.

  1. Press the lock to release the grease filter and carefully remove it.
  2. Insert the new filter on one side of the motor unit and turn the filter clockwise to secure it. Repeat this with the second filter.
  3. Replace the grease filter.

Power on/off and power settings
To turn on the hood, press the appropriate speed: , or .
Speed 1 – low speed, suitable for gentle boiling.
Speed 2 – medium speed, suitable for normal cooking.
Speed 3 – high speed, suitable for quick removal of steam and vapor during cooking or frying. To turn off the hood, press the button .

CLEANING AND MAINTENANCE

Always switch off the appliance, disconnect the power cord plug from the mains socket prior to cleaning or any maintenance.

Warning:
Never immerse the appliance, power cord or plug in water or other liquids.
Do not use plastic or metal scrapers, harsh cleaners, chemicals, petrol, solvents or other similar substances to clean any parts of the appliance. The surface finish could be seriously damaged.

Regular cleaning

Use a soft sponge, slightly moistened in lukewarm water with a little detergent. Wipe with dry dish towel.

Grease filter
The grease filter has to be cleaned at least once a month. The grease filter captures grease, smoke and dust. It has a direct effect on the performance of the hood.

Warning:
There is a risk of fire if the grease filter is not cleaned regularly.

  1. Press the lock to release the grease filter and carefully remove it.
  2. Wash the grease filter in warm water with a little dishwashing liquid.
  3. Rinse and wipe dry.
  4. Install in place and replace the front cover.

Warning:
Before installing the grease filter, make sure it is completely dry.

Note:
You can wash the grease filter in the dishwasher. Place it vertically in the
upper basket to increase washing efficiency. However, the water temperature should not exceed 65 °C.

Carbon filters replacement.
Note:
Do this step if you are using the recirculation method.
Carbon filters absorb unpleasant odors from cooking. Their saturation occurs through long-term use, intensive cooking and regular cleaning of the grease filter. We recommend to replace the carbon filters every 3 months. Always change all the filters in the same time.

  1. Carefully remove the grease filter.
  2. Turn the carbon filter counterclockwise to loosen it and carefully remove it. Repeat this with the other filter.
  3. Insert the new filter on one side of the motor unit and turn the filter clockwise to secure it. Repeat this with the second filter. Make sure both filters are inserted correctly. Improper installation can cause abnormal noise and vibrations, which can lead to damage to the hood.
  4. Insert the grease filter

Light replacement

  1. Switch off the hood and disconnect it from the power socket.
  2. Loosen the screws of the lighting cover and carefully remove the cover.
  3. Unscrew the fluorescent light.
  4. Insert a new fluorescent light of the same type.
  5. Replace the cover and fasten with screws.

TROUBLESHOOTING

Problem Cause Solution
The lighting comes on, but the range hood does not start working. The fan is
blocked. Switch off the hood and contact an authorized service.

The motor is damaged.
Neither the lights nor the hood turn on.| The fluorescent light isbroken.| Replace the fluorescentlight.
The plug is not inserted properly in the socket.| Check the plug connec- tion in the socket.
The range hood emits strong vibrations.| The fan is blocked.| Switch off the hood and contact an authorized service.
The fan motor is not prop- erly tightened.
The range hood is not properly installed.| Carefully remove the hood and reinstall it.
Poor hood performance.| The hood is placed too high above the hob.| The recommended dis- tance between the range hood and the hob is 65 to 75 cm.

If the problem is not listed in the table above or if the problem persists, switch off the appliance, disconnect the plug from the electrical outlet and contact an authorized service center.

The use of the WEEE Symbol indicates that this product should not be treated as household waste. By ensuring this product is disposed of correctly, you will help protect the environment. For more detailed information about the recycling of this product, please contact your local authority, your household waste disposal service provider, or the shop where you purchased the item.
This product meets all of the related basic EU regulation requirements. The EU dec‑ laration of conformity is available on www. alzashop.com/doc.
This product sold in the European Union meet the requirements of Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS).

Alza.cz, a. s., Jankovcova 1522/53, 170 00 Prague 7, Czech Republic
© 2022 Alza.cz, a. s. All Rights Reserved.
www.siguro.net

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals