AcuityBrands 1000W ISM Modular Inverter System User Manual

AcuityBrands 1000W ISM Modular Inverter System

IISM MODULAR INVERTER SERIES
1000W – 2000W
Users Manual

CAUTION
READ ENTIRE MANUAL AND REVIEW ALL DOCUMENTATION BEFORE ATTEMPTING SYSTEM INSTALLATION

FOR SERVICE OR INSTALLATION INFORMATION:
TELEPHONE: 610-868-5400 (24 HR. HOTLINE)
FAX: 610-954-8227

FOR YOUR PROTECTION
PLEASE COMPLETE AND RETURN WARRANTY REGISTRATION CARD IMMEDIATELY.
This unit contains LETHAL VOLTAGES. All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY! There are NO USER SERVICEABLE PARTS inside this unit.

IMPORTANT SAFEGUARDS

When using electrical equipment, you should always follow basic safety precautions, including the following:

1. READ AND FOLLOW ALL SAFETYINSTRUCTIONS.
2. Do not install the system outdoors.
3. Do not install near gas or electric heaters or in other high-temperaturelocations.
4. Use caution when servicing batteries. Depending on battery type, batteriescontain either acid or alkali and can cause burns to skin and eyes. Ifbattery fluid is spilled on skin or in the eyes, flush with fresh water andcontact a physician immediately.
5. Equipment should be mounted in locations where unauthorized personnelwill not readily subject it to tampering.
6. The use of accessory equipment not recommended by Manufacturer maycause an unsafe condition and void the warranty.
7. Do not use this equipment for other than its intended use.
8. Qualified service personnel must perform all servicing of this equipment.

SAVE THESE INSTRUCTIONS

The installation and use of this product must comply with all national, federal, state, municipal, or local codes that apply. If you need help, please call Service.
User’s Guide

• An on-site permanent log of the inspection, testing, and maintenance of the emergency electrical power supply system shall be maintained in accordance with the Manufacturer’s operating manual. The log shall include:
• The date on which the inspection, testing, and maintenance exercise was carried out.
• The name of the person(s) who performed the inspection, testing, and maintenance.
• A note of any unsatisfactory condition observed or discovered, and the steps taken to correct the condition.

INTRODUCTION

Keep this manual and the System Installation Guide in the folder mounted inside the unit.
This unit is a microprocessor controlled PWM (Pulse Width Modulated) pure sine wave based DC to AC power inverter utilizing MOSFET technology. It integrates a fully automatic 3-rate battery charger, a solid-state transfer system, control circuitry, self testing and recording digital meter display, and maintenance free sealed lead calcium type batteries. The system components are carefully matched to make the unit a completely self-contained, fully automatic standby power source for operation on all types of lighting loads. The batteries are sized and tested per UL-924 and Life Safety Code ANSI / NFPA 101, providing emergency power for a minimum of 90 minutes. If the duration of a power failure is greater than the batteries storage capability, the inverter will automatically shut down when the battery voltage reaches 85% of the nominal DC voltage. This feature protects the battery from being permanently damaged from a deep discharge that could cause cell reversal. This battery protection feature is called “Low Voltage Disconnect” or L.V.D. When the AC power is restored after a full discharge, the system will be ready for another power failure within 24hrs. If another power failure occurs before the 24-hour recharge time, the run time will be decreased. The front panel display incorporates an alphanumeric 2×20 LCD character display, LED status indicators and a 4 x 4 keypad. All user interface functions are available from the front panel assembly. Utilizing a small footprint, this unit is for use with any lighting load including quartz, HID, incandescent, fluorescent and halogen.

HOW TO USE THIS MANUAL

This manual tells you how to start, operate, and communicate with your unit and lets you know how to get more information for special situations.
Please record your unit’s model number, serial number, and part number below. You can find these numbers on the labels on the inside panel.

Model Number __
Serial Number __
Part Number ___

Service and Support

We are committed to outstanding customer service. A service technician is available 24 hours a day, 365 days a year. Service is also available 24 hours a day to give you access to technical notes and product information. You can also visit our web site.
NOTE : Please have your unit’s Serial and Model numbers available when you call; this number is located behind the left door.
Contact SERVICE one of the following ways:
Service Number: 610-868-5400
Service Fax: 610-954-8227

ENVIRONMENT

Make sure the environment is a clean, cool, dry place with normal ventilation.
Storage Temperature
Store the batteries (in the system or battery cabinet) at -18 to 40°C (0 to 104°F). Batteries have a longer shelf life if they are stored below 25°C (77°F). Keep stored batteries fully charged. Recharge the batteries every 90–120 days. The system or battery cabinet without batteries may be stored at -20 to 70°C (-4 to 158°F).

Ventilation
The air around the unit must be clean, dust-free, and free of corrosive chemicals or other contaminants. Do not place the system or batteries in a sealed room or container.

Operating Temperature
System can operate from 20° to 30°C (68° to 86°F) and up to 95% relative humidity. The batteries’ service life is longer if the operating temperature stays below 25°C (77°F).

Batteries
The temperature should be near 25°C (77°F) for optimum battery performance. Batteries are less efficient at temperatures below 18°C (65°F), and high temperatures reduce battery life. Typically, at about 35°C (95°F), battery life is half of what it would be at a normal temperature of 25°C (77°F). At about 45°C (113°F), battery life is one-fourth of normal. Make sure that heaters, sunlight, air conditioners, or outside air vents are not directed toward the batteries. These conditions can make the temperature within battery strings vary, which can cause differences in the batteries’ voltages. Eventually, these conditions affect battery performance. If the batteries are not in the system, remember that the batteries should be installed as close as possible to the unit to reduce DC wiring costs and improve battery performance. Do not allow tobacco smoking, sparks, or flames in the system location because hydrogen is concentrated under the vent cap of each cell of the battery. Hydrogen is highly explosive, and it is hard to detect because it is colorless, odorless, and lighter than air. Every type of battery can produce hydrogen gas, even sealed maintenance-free batteries. The gas is vented through the vent caps and into the air, mainly when the unit is charging the batteries. The batteries produce the most hydrogen when maximum voltage is present in fully charged batteries; the batteries do not produce hydrogen during float charging. The amount of current that the charger supplies to the batteries (not the battery ampere-hour) determines how much hydrogen is produced.

High Altitude Operation
The maximum operating ambient temperature drops 1°C per 300m (2°F per 1000 ft) above sea level. Maximum elevation is 3000m (10,000 ft).

STARTUP AND SHUTDOWN PROCEDURE

Refer to the Installation Manual to secure the unit and install AC and DC wiring.

STARTUP PROCEDURE
For the initial startup of the system, please fill out the blue warranty card. Failure to do so will void warranty.
CAUTION: HAZARDOUS VOLTAGES – ONLY QUALFIED SERVICE PERSONNEL SHOULD PERFORM PROCEDURE.

1. Verify that the installation switch located below the front panel is in the OFF position. Verify that AC input is disconnected.
2. Turn on the DC Circuit Breaker CB1.
3. Energize the Mains AC input by turning on the units input circuit breaker and/or the Distribution Panel breaker located upstream from the inverter.
4. Turn the installation switch to the On position. The Front Panel display should now be illuminated and a slight hum should be heard from the inverter transformer. The unit is now charging and the output should be energized. Now turn on the output circuit breaker(s).

SHUTDOWN PROCEDURE

1. Interrupt the AC Mains to the machine by the Distribution Panel Breaker or the machines input circuit breaker. The Inverter should then start.
2. Turn the installation switch located on the inverter chassis to the off position. The inverter should stop.
3. Turn off the DC Circuit Breaker CB1

CAUTION: HAZARDOUS VOLTAGES STILL EXIST AT THE BATTERY TERMINAL BLOCK AND WITHIN THE SYSTEM. AUTHORIZED SERVICE TECHNICIANS MUST DISCHARGE DC CAPACITORS AND TURN OFF UTILITY POWER BEFORE SERVICING EQUIPMENT.
CAUTION: DO NOT LEAVE THE SYSTEM SHUTDOWN FOR A PROLONGED LENGTH OF TIME. LEAD BASED BATTERIES WILL EXPERIENCE PERMANENT DAMAGE FROM LACK OF CHARGING AFTER A FEW MONTHS

**OPERATION

**

The following is a description of the status LED’s located on the front panel and the internal fan.

AC Present
When the AC Mains is present, the LED will illuminate. If a power failure was long in duration, or the AC mains was disconnected by some other means (Circuit breaker open) the AC Present LED would not be illuminated. When the control circuit senses that the line has dropped below an acceptable level (Black Out, Brown Out, or Transient), the inverter will energize for at least one minute. So, if the power failure was a momentary glitch, the AC present LED would be illuminated but the inverter would be running.

System Ready
When the system has adequate battery voltage to transfer, the System Ready LED will illuminate. This feature prevents damage from multiple deep discharges of the battery.

Battery Charging
When the AC Mains is connected to the line and the battery is charging under normal conditions, the Battery Charging LED will illuminate.

Battery Power
When the inverter is producing output power (battery is being discharged), the Battery Power LED will be illuminated.

Fault
This is a summary Fault indication. When there is a fault condition present, the Fault LED will illuminate. To view which fault is present, use the keypad and LCD display feature.
The front panel display will provide the user with a variety of information. It has a full compliment of Meter functions, Control functions and Program functions.

Fan
The fan operates during emergency mode and only during normal mode when the batteries are being charged. When the batteries reach float condition (trickle charge) the fan turns off.

FRONT PANEL DISPLAY

The Front panel consists of a 2 x 20 alphanumeric LCD display with LED Back lighting, 5 Status LED indicators and a 4 x 4 keypad for user interface .

Control Panel Keypads

Table 5.1 Keypad Functions

Meter Functions

Meter functions are available by pressing the METER keypad to get to the Meter Menu and then pressing the desired function keypad. (See figure 5.1)

Table 5.2 Meter Functions

Normally Off loads are connected, it will read the sum of Normally On and Normally Off outputs.| I OUT
Battery Voltage| Measures Battery Voltage| V BATT
Battery Current| Measures the Battery Current. When in charge mode, the current will be positive. When in Inverter mode, the current will be negative.| I BATT
VA Output| Multiplication of the output voltage and output current| VA OUT
Inverter Watts| Multiplication of the battery voltage and the battery current| INV. WATTS
Inverter Minutes| Total minutes the system has run on inverter| INV. MIN
Temperature| Measures the ambient temperature of the electronics enclosure.| TEMP
System Days| Total days the system has been in service.| SYS. DAYS

Control Functions
Control functions are available by pressing “CONTROL” to get to the Control Menu and then pressing the desired function.
Table 5.3 Control Functions

• TEST LOG – View the Test Log of the last 75 monthly or Yearly Tests. View the Date, Time, Duration, Output Voltage, Output Current, Temperature and Fault Status.
  Use the left and right scroll key to change event number.
  Use the ENTER key to select desired event number.
  Use the left and right scroll key to view event information about the event.
  Use the TEST LOG key to return to the event number.

• EVENT LOG – Identical to the TEST LOG except this log records the past 75 events.

• TEST – Pressing the TEST key will initiate a 1-minute test. This test will be recorded in the Event log since it is not part of the scheduled monthly or yearly test.

• ALARM – View the Alarm log of the last 50 alarms. View the Date, Time and Alarm.
  Use the left and right scroll key to change alarm number.
  Use the enter key to select alarm number.
  Use the left and right scroll key to view information about the alarm.
  Use the ALARM key to return to event number.

• BUZZER – Pressing this key silences the audible buzzer from a fault condition or an intermittent beep when the inverter is under battery power. If a fault caused the buzzer to alarm and the alarm is silenced, the buzzer will return after 24 hours or after the fault is cleared.

Program Functions
User Program Functions
All program functions are password protected. The password for user level is 1234. When the PROGRAM keypad is pressed, the display will prompt the user for the password. After the password is entered (1234 + ENTER key), the user can change the Date, Time, Month Test Date, Month Test Time, Yearly Test Date and Yearly Test Time, Load Reduction Fault, Low VAC Alarm, High VAC Alarm, Ambient Temp Alarm and Near Low Battery settings.
Time is always in the 24 hour standard. Example 4:00 PM is 16:00.

Table 5.4 Program Functions

• Near Low Battery Voltage is in VVVV (Volts). The last digit entered is after the decimal place. I.E. (430 + ENTER) will register 43.0VDC.
  Load Reduction Fault is in AAAA (Amps). The last digit entered is after the decimal place.
  I.E. (480 + ENTER) will register 48.0 Amps. If the output current under battery power is 10 percent below this number, the alarm will be set.

• Low AC Voltage Alarm is in VVVV (Volts). The last digit entered is after the decimal place. I.E. (1200 + ENTER) will register 120.0 Volts. If the Input AC Voltage goes below this number the alarm will be set.

• High AC Voltage Alarm is similar to Low AC Voltage Alarm.

• Ambient Temperature Alarm is in DDD (Degrees Centigrade). I.E. (75 + ENTER) will register 75 deg. C. When the ambient temperature internal to the inverter enclosure goes above the set point the alarm will be set.

SPECIFICATIONS

MAINTENANCE AND SERVICE

The Self-testing feature of the inverter ensures that the system is tested at least once per month for 5 minutes and once per year for 90 minutes. If there are any problems with the self-tests, the fault log shall indicate which faults occurred. Please see the fault descriptions and troubleshooting guide. A few simple maintenance operations performed periodically will help ensure many years of trouble-free operation. Battery terminals should be checked for tightness and corrosion. If severe corrosion is evident, maintenance is required to correct this situation. Since the unit depends on unrestricted airflow for cooling of power handling components, it is important to keep the air vents free of any obstruction. If the environment tends to be extremely dusty, occasionally blow away any accumulation of dust on components. Please follow the shutdown procedure before cleaning.
CAUTION: Follow the shutdown procedure (See Chapter 3) before cleaning. An authorized technician only should perform Service!
Table 7.1 Preventive Maintenance Schedule

SERVICE TO PERFORM:

| PERFORM SERVICE EVERY:
---|---
3 MONTHS| 6 MONTHS| 12 MONTHS

1. TEST UNIT:

NOTE: Perform manual test only when critical load is connected but not required.

—– Output voltage should be present.

—– Confirm operations of front panel indicators.

| X|  |
 |  |
 |  |
 |  |
 |  |
 |  |
 |  |
 |  |

2. INSPECT BATTERIES:

—– All connections are tight.

—– Connections have no corrosion. (Clean if necessary).

|  | X|
 |  |
 |  |
 |  |
 |  |
 |  |
 |  |
 |  |

CLEAN UNIT: NOTE: Unit must be shut down during this service.

—– Inspect air vents and clean if necessary.

—– Clean excessive dust from inside cabinet(s).

—– Clean excessive dust from fan(s).

|  |  | X
 |  |
 |  |
 |  |
 |  |
 |  |
 |  |
 |  |

“X” Indicates when to perform service. Lines below the “X” are for the date of service

TROUBLE SHOOTING CHART

THE NUMBER IN THE CHART INDICATES ORDER IN WHICH

PROBLEMS SHOULD BE CHECKED

| S Y M P T O M S| Inverter will not run

during a power

failure

| System draws

excessive AC input current

| System noisy, excessive transformer hum during normal run conditions| AC output voltage

low during a utility power failure

| System

overheats, smells,

smokes, etc.

| System noisy,

transformer hum

during a power

failure

| Inverter jitters or staggers during a power failure| System blows battery fuse (& fuses in battery cabinet if applicable)| Charger not

charging properly, batteries low or

dead

| Charger stays in HI

charge

| Batteries require

continuous addition of water to

keep proper level (optional w/ wet cells)

| Battery acid

leaking in

cabinet or

around tops of

batteries

| Battery voltage does

not read properly after Installation of

fresh cells

| B a tte r y Voltage lo w

or non existent

---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
PR O B L EM S
Installation switch on inverter in off position| 1|  |  |  |  |  |  |  |  |  | |  |  |
S hor t ed I G B T m odul e( s )| 3|  |  | 3| 3|  | 1| 3|  |  |  |  |  |
No AC input voltage|  |  |  |  |  |  |  |  | 2|  |  |  |  |
D ef ec t i v e i n v er t er| 4|  |  | 2| 2| 1| 3| 5|  |  |  |  |  |
Output volt- ampere rating of unit being exceeded| 6| 1|  | 1| 1| 2| 2| 6|  | |  |  |  |
Ambient temperature too high, vents blocked|  |  |  |  |  |  |  |  |  |  | 3| 1|  |
S hor t ed l oa d|  | 2|  | 4|  | 3|  |  |  |  |  |  |  |
R ev er s e bat t er y d i odes s hor t ed|  |  |  |  |  |  |  | 2|  |  |  | |  |
Open battery fuse (&

fuses in battery cabinet if applicable)

| 2|  |  |  |  |  |  |  |  |  |  |  |  | 1
Battery polarity w r ong|  |  |  |  |  |  |  | 1|  |  |  |  |  |
D ef ec t i v e c har g er| 11|  | 1|  | 4|  |  |  | 6| 1| 1| 2| 4| 2
B at t er y c a pac i t y l ow| 7|  |  |  |  |  |  |  |  |  |  |  | 3| 3
Low w at er i n bat t er y ( optional w/ wet cells)| 10|  |  |  |  |  |  |  | 3|  |  |  |  | 4
Wrong amount of battery cells in series| 9|  | 2|  | 6|  |  | 4| 4| 2| 2| 4| 1| 5
Batteries dead, low or defective| 8|  |  |  |  |  |  |  | 5| 3| 4| 3| 2|
Transfer module and/or control circuit

malfunction

| 5|  |  |  |  |  |  |  |  |  |  |  |  |
Transformer not connected for proper voltage|  | 3| 3|  | 5|  |  |  | 1|  |  | |  |

WARRANTY

For warranty information on IOTA IIS Central Inverters and battery components, visit www.iotaengineering.com or call IOTA Customer Service.
OUT OF WARRANTY REPAIR CHARGES AND LABOR
Contact Field service for current parts and labor rates. A minimum rate will be assessed. The manufacturer will not proceed with repairs of an out of warranty unit until authorization in the form of a purchase order is received from the customer. The unit for repair must be returned prepaid with an RMA number on the carton. For travel to the job site, a quote “Not to Exceed” estimate will be given. A purchase order to cover that amount is required before a trip to the job site is made.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>