D-Link DXS-1100-10TS Gigabit Ethernet Smart Managed Switches Installation Guide

D-Link DXS-1100-10TS Gigabit Ethernet Smart Managed Switches

Introduction

This Quick Installation Guide gives instructions for setting up the D-Link DXS-1100-10TS switch. The model you have purchased may appear slightly different from those shown in the illustrations. For more detailed information about the device, its components, making network connections and technical specifications, please refer to the User Manual.

Package Contents

These are the items included with your DXS-1100-10TS purchase:

• DXS-1100-10TS Switch
• Power Cord
• Cord Retainer
• 4 Rubber Feet
• 2 Mounting Brackets
• Mounting Kit
• Quick Installation Guide

If any of the above items are damaged or missing, please contact your local reseller for replacement.

Front Panel Overview

LED Indicators

offline
Link/Act/Speed (for port)| Green/Amber| Solid Green| When there is a secure 10Gbps connection (or link) at any of the ports
Blinking Green| When there is reception or transmission (i.e. Activity-Act) of data occurring at any of the ports
Solid Amber| When there is a secure 1000Mbps Ethernet connection (or link) at any of the ports
Blinking Amber| When there is reception or transmission (i.e. Activity-Act) of data occurring at any of the ports
Light off| No link

Buttons

• Reset: by pressing and holding the Reset button inside the pinhole for 3 to 5 seconds, the Switch will change back to the default configuration and all changes will be lost.

Installation

Desktop or Shelf Installation
When installing the switch on a desktop or shelf, the rubber feet included with the device must be attached on the bottom at each corner of the device’s base. Allow enough ventilation space between the device and the objects around it. Rack Installation
The switch can be mounted in a standard size 19-inch rack, which can be placed in a wiring closet with other equipment. To install, attach the mounting brackets to the switch’s side panels (one on each side) and secure them with the screws provided.Then, use the screws provided with the equipment rack to mount the switch in the rack.

Connecting to Power

Power Failure
As a precaution, the switch should be unplugged in case of power failure. When power is resumed, plug the switch back in.

Grounding the Switch
The following steps explain the procedure for connecting the switch to a protective ground:

1. Verify if the system power is off.
2. Using a screwdriver, tighten the ground screw to secure the ground cable to the switch.
3. Attach the terminal lug ring at the other end of the grounding cable to an appropriate grounding source.
4. Verify if the connections at the ground connector on the switch and the rack are securely attached.

Plugging in the AC Power Cord with Power Cord Clip

• A) With the rough side facing down, insert the Tie Wrap into the hole below the power socket.
• B) Plug the AC power cord into the power socket of the Switch.
• C) Slide the Retainer through the Tie Wrap until the end of the cord.
• D) Circle the tie of the Retainer around the power cord and into the locker of the Retainer.
• E) Fasten the tie of the Retainer until the power cord is secured.
• F) Users may now connect the power cord (AC 100/240 V) to an electrical outlet.

Managing the Device

Management Options
The DXS-1100-10TS can be managed through any port by using the Web-based Management. Each switch must be assigned its own IP Address, which is used for communication with the Web-Based Management or a SNMP network manager. The PC should have an IP address in the same subnet as the switch. Each switch can allow up to four users to access the Web-Based Management concurrently.

Using Web-based Management

After a successful physical installation, you can configure the Switch, monitor the network status, and display statistics using a web browser.

Supported Web Browsers

• Internet Explorer 7 or later version
• Google Chrome
• Firefox
• Safari

Connecting to the Switch
You will need the following equipment to begin the web configuration of your device:

1. A PC with a RJ-45 Ethernet connection
2. A standard Ethernet cable

Connect the Ethernet cable to any of the ports on the front panel of the switch and to the Ethernet port on the PC.

Login Web-based Management
In order to login and configure the switch via an Ethernet connection, the PC must have an IP address in the same subnet as the switch. For example, if the switch has an IP address of 10.90.90.90, the PC should have an IP-address of 10.x.y.z (where x/y is a number between 0 ~ 254 and z is a number between 1 ~ 254), and a subnet mask of 255.0.0.0. Open the web browser and enter 10.90.90.90 (the factory-default IP address) in the address bar. Then press