FIBARO FGBHCD-001 HomeKit CO Sensor User Manual
- June 9, 2024
- FIBARO
Table of Contents
- FIBARO FGBHCD-001 HomeKit CO Sensor
- Important safety information
- HomeKit technology
- Description and features
- Powering the accessory
- Pairing the accessory
- Physical installation
- Operating the device
- Functionality
- Visual indications & acoustic signals
- Battery
- Specifications
- Regulations
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
FIBARO FGBHCD-001 HomeKit CO Sensor
Important safety information
Read this manual before attempting to install the device!
Failure to observe recommendations included in this manual may be dangerous or
cause a violation of the law. The manufacturer, Fibar Group S.A. will not be
held responsible for any loss or damage resulting from not following the
instructions of operating manual.
General carbon monoxide information
Carbon monoxide (CO) is a colourless, odourless, and tasteless poison gas that
can be fatal when inhaled. It is produced when liquid, solid, or gas fuel is
burned.
Symptoms of carbon monoxide poisoning
The early symptoms of carbon monoxide poisoning can be confused with flu-like
symptoms: headache, dizziness and nausea. Breathing car-bon monoxide causes
these symptoms even in healthy people. It can also cause sleepiness, vision
problems (including blurred vision), ring-ing in the ears, aching arms and
legs, irregular breathing, fatigue and confusion. At very high levels, it
causes loss of consciousness and death.
Some external factors, eg. exposure to high concentration of basic (non-
acidic) gases, silicone vapors, hydrogen sulfide or sulfuric acid gas, organic
vapors, contact with water, dust and oil mist, or dew condensa-tion may affect
the reliability of the device operation.
This device may not protect from long-term exposure to low levels of carbon
monoxide which can also lead to neurological symptoms.
The device is not a substitute for appropriate ventilation and exhaust
systems.
WARNING: apparatus may not prevent the chronic effects of carbon monoxide
exposure. The apparatus will not fully safeguard individuals at special risk.
This product is not a toy. Keep away from children and animals!
Risk of malfunction as a result of tampering with the device.
The device should be installed below the ceiling level.
The device should not be installed: in a bathroom, next to heat sources,
within range of kids, obstructed from possible carbon monoxide sourc-es, in
direct sunlight.
Do not paint the device.
The device should be cleaned with a slightly damp cloth or moistened tissue.
Replace the device before date on the front or if sensor error is detected.
Risk of explosion if battery is replaced by an in correct type. Dispose of
used batteries according to the instructions.
If there is any question as to the cause of an alarm, it should be assumed
that the alarm is due to a dangerous level of carbon monoxide and the dwelling
should be evacuated.
HomeKit technology
Apple HomeKit technology provides an easy, secure way to control HomeKit-
enabled accessories using Siri on your iPhone, iPad, or iPod touch.
After installing your FIBARO CO Sensor, configure it from a compatible app
with just a few simple steps.
You can even create your own custom scenes to control your home settings. For
example, you can create a scene to automatically turn off the lights, lock
your doors, close the garage door, and set the thermostat to the desired
temperature in just one step.
Controlling this HomeKit-enabled accessory requires an iPhone, iPad, or iPod
touch with iOS 9.3 or later.
Controlling this HomeKit-enabled accessory away from home requires a third-
generation Apple TV with Apple TV software 7.2.1 or later or a fourth
generation Apple TV with tvOS 9.2 or later and an iPhone, iPad, or iPod touch
with iOS 9.3 or later
Description and features
FIBARO CO Sensor is a HomeKit-enabled carbon monoxide detector using
Bluetooth® low energy technology.
Its high sensitivity allows to detect the presence of the carbon monoxide (CO)
gas at the early stage in order to prevent carbon monoxide poisoning.
Alarm is signalled with a built-in siren, blinking LED indicator and by
sending information to your iOS device.
Additionally, the accessory is equipped with a temperature sensor.
Main features of FIBARO CO Sensor:
- compatible with Apple HomeKit technology
- Bluetooth® low energy technology for wireless communication
- detects tampering when the casing is opened
- wall-mounted
- battery-powered
- alarm signalled with a built-in siren and LED diode
- built-in temperature sensor measuring ambient temperature
Powering the accessory
NOTE
FIBARO CO Sensor may operate as a stand-alone carbon monox-ide detector or may
be used in cooperation with HomeKit technol-ogy as a part of smart home
system.
- Turn the cover counter-clockwise.
- Take off the cover.
- Remove the paper strip protecting the battery.
- Proper powering up will be confirmed with a short beep.
- Pair the accessory if you want to use it with HomeKit.
Pairing the accessory
-
Open the Settings app on your iOS device.
-
Go to the Bluetooth® section, and turn the Bluetooth® on.
-
Place the accessory next to your iOS device.
-
Open a HomeKit compatible app of your choosing on your iOS device.
-
Open pairing window in your HomeKit app to detect available accessories.
-
Choose CO Sensor you wish to pair.
-
You can identify it – CO Sensor will blink green.
-
Find HomeKit Setup Code on the last page of Quick Start Guide included in the box that looks like this:
-
Start pairing with your HomeKit app.
-
Point your iOS device’s camera at the Setup Code to scan it or enter the Setup Code manually.
-
If entered Setup Code is valid, the device will complete the setup process.
-
Follow instructions displayed in the application.
NOTE
Remember to keep your HomeKit Setup Code in safe place. You may need it in
case of re-pairing.
Physical installation
READ BEFORE INSTALLATION AND HEED ALL THE WARNINGS!
- The accessory should be installed below the ceiling level.
- The accessory should be installed on the wall, at least 30 cm (1 ft) away from the corners.
- The accessory should not be installed: in a bathroom, next to heat sources, within range of kids, obstructed from possible carbon monoxide sources, in direct sunlight.
- The accessory should be installed by a qualified installator.
- Do not paint the accessory.
- The accessory should be cleaned with a slightly damp cloth or moistened tissue.
Place of installation:
NOTE
Recommended height of installation is de-pendant on the purpose of the room
and height at which head typically is.
Installation on the wall:
- Mount the cover on a wall.
- Attach the accessory to its cover.
- Turn the accessory clockwise to close it.
Operating the device
Menu allows to perform different actions. In order to use the menu:
-
Press and hold the button for 3 seconds.
-
You should hear a short signal while the LED diode blinks white.
-
Release the button.
-
Wait for the device to indicate desired menu position with a colour:
- White – confirm the start of the firmware update process
- Green
- Magenta – reset the CO peak value
- Yellow – the device reset
-
Press the button to confirm selection.
NOTE
CO Sensor must be detached from the wall and battery level must be greater
than 30% of its full capacity to perform the firmware update process.
Resetting the accessory to factory defaults:
Reset procedure allows to restore the accessory back to its factory settings
including HomeKit pairing. Stored carbon monoxide and temperature measurement
are not deleted.
- Press and hold the button.
- Release the button when LED indicator glows white and short beep sounds.
- Click the button when LED indicator glows yellow.
- After few seconds the device will be reset (confirmed by red LED indicator and long beep).
Self-test allows to check operation of the accessory.
To start the self-test:
- Press and hold the button.
- The LED indicator will glow white and you will hear a short beep.
- Release the button when you hear the first alarm sequence.
- Move away from the accessory to protect your hearing.
If the self-test procedure does not result in emitting sound and red light signal, replace the accessory.
CAUTION
The alarm is very loud! Only the first alarm sequence is quieter.
Functionality
Carbon monoxide alarm:
The CO Sensor alarms about abnormal levels of carbon monoxide concentration
with 4 red blinks and 4 loud beeps (every 5 seconds).
Alarm is also reported to your iOS device.
Carbon monoxide measuring and storing:
The CO Sensor measures carbon monoxide concentration and re-ports. If measured
value differs from previously reported by at least 1ppm, accessory reports it
to your iOS device.
Last 2500 measurements are stored in non-volatile memory of the ac-cessory and
can be accessed via FIBARO for HomeKit app.
Temperature measuring:
The CO Sensor measures ambient temperature every 30 seconds. If the measured
temperature differs from previously reported by at least 1°C (1.8°F),
accessory reports it to your iOS device.
Last 2500 measurements are stored in non-volatile memory of the ac-cessory and
can be accessed via FIBARO for HomeKit app.
Tamper detection:
The CO Sensor detects tampering when accessory is removed from its base and
reports it to your iOS device. Tampering is indicated with one white blink and
beep.
Battery level measuring:
The CO Sensor measures battery level every 6 hours and reports it to your iOS
device. Additionally, if battery level is below 15%, the acces-sory will
report low level battery status to your iOS device and indicate it with one
yellow blink and beep.
NOTE
The accessory measures temperature in the place of installation. Remember that
temperature near the ceiling may differ from that on eye-level or the floor.
Visual indications & acoustic signals
Indications and signals:
The CO Sensor is equipped with a LED diode and a buzzer, signalling menu
position and status of the accessory.
Accessory status indications:
what you hear | what you see | what it means | what to do |
---|
4 x BEEP
every 5s
|
4 x RED BLINK
every 5s
| Detected pres- ence of carbon monoxide which can kill you!| 1. Open the windows
2. Move to fresh air!
3. Contact emergency services
1 x BEEP
| 1 x YELLOw BLINK
every 30s
|
Low battery level
|
Replace the battery
2 x BEEP
every 60s
|
2 x YELLOw BLINK
every 60s
| Sensor error
DOES NOT DE- TECT CARBON MONOXIDE
|
Reset the accessory, replace if no effect
3 x BEEP
every 60s
|
3 x YELLOw BLINK
every 60s
|
End of lifespan
|
Reset the accessory, replace if no effect
3 x BEEP
every 30s
| 1 x BLUE BLINK
every 30s
|
Heat alarm
|
Be cautious of fire
1 x BEEP| 1 x wHITE BLINK| Tamper alarm| Check the housing
–
| 1 x GREEN BLINK
every 60s
| Accessory powered|
–
1 x BEEP
| 1 x GREEN BLINK
after powering
| Paired with HomeKit|
–
1 x BEEP
| 1 x RED BLINK
after powering
| Not paired with HomeKit|
–
–| CYAN BLINKING| Firmware update| wait for completion
NOTE
Replace the accesso-ry before date on the front or if sensor error is
detected.
Battery
FIBARO CO Sensor can be powered with CR123A (included) battery. Estimated battery life with accessory on default settings is 3 years (tested with Panasonic Industrial Lithium).
Checking battery level:
The CO Sensor measures battery level every 6 hours and reports it to your iOS
device. Additionally, if battery level is below 15%, the acces-sory will
report low level battery status to your iOS device and indi-cate it with one
yellow blink and a short beep.
Replacing the battery:
- Remove the accessory from the cover by turning it counter-clockwise.
- Pull the paper strip to take out the battery.
- Press and hold the button for at least one second.
- Insert a new CR123A battery observing the polarities shown inside.
- Attach the accessory to its cover by turning it clockwise and perform the test (as decribed in #5: Operating the device).
- Launch your HomeKit app and swipe down to refresh the device state.
CAUTION
Using batteries other than specified may result in explosion. Dispose of
properly, observing environ- mental rules.
CAUTION
Use only type of bat-tery specified in this manual and keep proper polarity!
NOTE
It is required to launch the HomeKit-compatible app, open the accessory view
and swipe down the screen to refresh its state after each battery replace-
ment.
Specifications
- Power supply: CR123A 3.0V battery (included)
- Battery life: 3 years on default settings (tested with Panasonic Industrial Lithium)
- Lifespan under typical conditions: 8 years
- CO concentration measurement range: 0 – 450 ppm
- Measuring accuracy: ±10ppm / ±5%
- Alarm response times: 50ppm 60-90min 100ppm 10-40min 300ppm <1.5min
- Alarm siren sound level: 85 dBA at 3 meters (10 feet)
- Operating temperature: 0 – 50°C (32-122°F)
- Operating humidity: 10-95%RH without condensation
- Conformity with EU requirements: RED 2014/53/EU RoHS 2011/65/EU RoHS 2015/863/EU EN 50291-1:2018
- Radio protocol: Bluetooth® low energy
- Radio frequency: 2.4 GHz
- Range: up to 50m (free range) (164 feet)
- Dimensions (d x h): 65 x 28 mm (2.56 x 1.1 inches)
- Type of apparatus:Type B
CAUTION
Using batteries other than specified may result in explosion. Dispose of
properly, observing environmental rules.
NOTE
Replace the accessory before date on the front or if sensor error is detected.
Regulations
Legal Notices
All information, including, but not limited to, information regarding the
features, functionality, and/or other product specification are subject to
change without notice. Fibaro reserves all rights to revise or update its
products, software, or documentation without any obligation to no-tify any
individual or entity.
FIBARO and Fibar Group logo are trademarks of Fibar Group S.A.
Apple, iPhone, iPad, iPad Air, and iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries. HomeKit is a trademark of Apple
Inc.
The Bluetooth word mark is registered trademark of Bluetooth SIG, Inc.
All other brands and product names referred to herein are trademarks of their
respective holders.
Use of the Works with Apple HomeKit logo means that an electronic accessory
has been designed to connect specifically to iPod touch, iPhone, or iPad,
respectively, and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of this
device or its compliance with safety and regulatory standards.
Warning
This product is not a toy. Keep away from children and animals!
Information according REACH
The included Panasonic CR123A battery contains 1,2-Dimethoxyeth-ane substance.
Normal use of the device does not expose the user to a given substance.
Declaration of conformity
Hereby, Fibar Group S.A. declares that the device is in compliance with
Directives 2014/53/EU and 2011/65/EU, 2015/863. The full text of the EU
declaration of conformity is available at the following internet address:
manuals.fibaro.com
WEEE Directive Compliance
Device labelled with this symbol should not be disposed with other household
wastes. It shall be handed over to the appli-cable collection point for the
recycling of waste electrical and electronic equipment.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>