FIBARO FGBWHWPE-102 Wall Adaptor Plug User Manual

FGBWHWPE-102 Wall Adaptor Plug
User Manual

Important safety information

Read this manual before attempting to install the device!
Failure to observe recommendations included in this manual may be dangerous or cause a violation of the law. The manufacturer,  Fibar Group S.A. will not be held responsible for any loss or damage resulting from not following the instructions of the operating manual.
This product is intended for indoor use only in dry locations.
Do not use it in damp or wet locations, near a bathtub, sink, shower, swimming pool, or anywhere else where water or moisture are present.
Caution!
To avoid the risk of electrical shock, do not operate the device with wet or moist hands.
Do not plug one Wall Plug into another Wall Plug.
Note
The socket used for the Wall Plug should be easily accessible.

HomeKit technology

Apple HomeKit technology provides an easy, secure way to control HomeKit- enabled accessories using Siri on your iPhone, iPad, or iPod touch.
After installing your FIBARO Wall Plug, configure it from a compatible app with just a few simple steps.
You can even create your own custom scenes to control your home settings. For example, you can create a scene to automatically turn off the lights, lock your doors, close the garage door, and set the thermostat to the desired temperature in just one step.

To control this HomeKit-enabled accessory, iOS 10 or later is recommended.
Controlling this HomeKit-enabled accessory automatically and away from home requires an Apple TV with tvOS 10 or later or an iPad with iOS 10 or later set up as a home hub.

Description and features

FIBARO Wall Plug is a HomeKit-enabled smart plug using Wi-Fi® connection and Bluetooth® low energy wireless technology.
This remotely controlled outlet adapter is equipped with an active power and energy metering function.
it uses a LeD ring to visualize current consumption and status.
The Wall Plug may be operated using the button on the casing or via an iOS mobile app through Wi-Fi.

Main features of FIBARO Wall Plug:

• Compatible with Apple HomeKit technology,
• Wi-Fi for wireless communication,
• Detects if an electrical device is connected to it,
• Measures active power consumption,
• Measures energy consumption,
• easy installation,
• indicates state and consumption using a multicolor LeD ring.

Pairing the accessory

1. Open the Settings app on your iOS device.

2. Go to the Wi-Fi section, turn the Wi-Fi on and connect to your preferred Wi-Fi network.

3. Go to the Bluetooth® section, and turn the Bluetooth® on.

4. Plug the Wall Plug into an electrical socket.

5. The LeD ring will be flashing yellow when ready for configuration.

6. Open a HomeKit-compatible app of your choosing on your iOS device.

7. Open the pairing window in your HomeKit app to detect available accessories.

8. Choose Wall Plug you wish to pair.

9. When prompted, allow the Wall Plug to connect to your Wi-Fi network.

10. Wait until the LeD ring starts flashing violet.

11. You can identify it – Wall Plug will triple-blink blue 3 times.

12. Find the HomeKit Setup Code on the last page of the Quick Start Guide included in the box that looks like this:

13. Start pairing with your HomeKit app.

14.  Point your iOS device’s camera at the Setup Code to scan it or enter the Setup Code manually.

15. if entered Setup Code is valid, the device will complete the setup process.

16. Follow the instructions displayed in the application.

Reset

Resetting the Wall Plug to factory defaults:

The reset procedure allows the restoration of the accessory back to its factory settings including HomeKit pairing.

1. Make sure the accessory is powered.

2. Press and hold the button.

3. When the LeD ring glows yellow, release the button.

4. immediately click the button again to confirm.

5. The accessory will glow red to confirm reset.

6. Delete the accessory from the app before pairing it again.

Functionality

Turning ON/OFF electrical devices:
The Wall Plug can turn On/OFF connected electrical devices either through the iOS mobile app or a button.

Multicolor LED ring:
The LeD ring of the Wall Plug glows when the device is turned On and displays current active power consumption. Additionally LED ring allows for navigating the built-in menu.

Menu:
The Wall Plug can be operated using the built-in menu.
To enter and navigate the menu:

1. Press and hold the button.

2. Release the button, when the LeD ring glows with the desired color:
   • VIOLET – Wi-Fi range test
   • RED – reset Wi-Fi settings
   • GREEN – reset energy counter
   • YELLOW – factory reset

3. immediately click the button again to confirm the selection.

Disabling the LED ring backlight:

1. Press and hold the button for about 3 seconds.
2. Release the button when the LeD ring starts pulsing white.
   To restore the LeD ring backlight perform the above procedure again.

Active power metering:
The Wall Plug measures the currently active power consumption of the connected device and reports it to your iOS device. The measured value is indicated by the color of the LED ring.
The active power measuring accuracy is ±1% for loads greater than 5W.

Energy metering:
The Wall Plug counts energy consumed by the connected device and reports accumulated value to your iOS device.

To reset the energy counter:

1. Press and hold the button.
2. When the LeD glows green, release the button.
3. immediately click the button again to confirm.

Plug insertion detection:
The Wall Plug detects if any device is plugged into it and reports it to your iOS device.

*Overload Control:**
Functionality allows to switch off connected load after 4 seconds from exceeding the power set by the user in Fibaro for the HomeKit app.

*Power Change Notification:**
Minimum and maximum allowed power consumption may be defined by the user in Fibaro for the HomeKit app. exceeding any of these values results in sending a notification.

*Timer Switch:**
Functionality allows setting time (in Fibaro for the HomeKit app) after which the connected load will be automatically turned on/turned off.
The timer will start after changing the On/OFF state to the opposite (through the app or connected wall switch). if the device state was changed before expiring of the set time, the counter will reset. it is possible to use both Turn On and Turn OFF functionality – it will result in cyclic load control.

NOTE

• Functionality available only in Fibaro for the HomeKit app.

Wi-Fi

Wi-Fi range test:
The Wall Plug can measure Wi-Fi signal strength and indicates it with the color of the LED ring:

• Green – good (≥ -45dBm)
• Yellow – fair (≥ -70dBm, < -45dB)
• Red – weak (< -70dBm)

To start the range test:

1. Press and hold the button.
2. When the LeD glows violet, release the button.
3. immediately click the button again to confirm.
4. LED ring will indicate signal strength with color.
5. The range test will be disabled after pushing the button.

Resetting Wi-Fi settings:
The Wall Plug allows you to reset your Wi-Fi settings and get new settings from your iOS device.
To reset Wi-Fi settings:

1. Press and hold the button.
2. When the LeD glows red, release the button.
3. immediately click the button again to confirm.
4. LED ring will glow yellow for 30 minutes while waiting for new settings from the iOS device.

Configurable parameters

1. Color of LED ring
This parameter allows choosing the color of the LED ring when the device is On.

Available settings:

| 0 – color dependent on measured active power

1 – color dependent on active power measurements with smooth transition between colors

2 – white, 3 – red, 4 – green, 5 – blue, 6 – yellow, 7 – cyan, 8 – magenta

9 – LED ring disabled

---|---
Default setting:| 1 (color dependent on measured active power with smooth transition between colors)

NOTE

• Colors depending on the measured value:
  0W – white
  100W – blue
  200W – green
  400W – yellow
  1000W – orange
  1800W – red
  2300W – violet

2. Measured power for blue LED ring color
This parameter allows setting the power value for the blue backlight of the LED ring.

NOTE
The value of parameter 2 must be lower than the value of parameter 3.

3. Measured power for the green LED ring color
This parameter allows setting the power value for the green backlight of the LED ring.

NOTE
The value of parameter 3 must be between values of parameters 2 and  4.

4. Measured power for the yellow LED ring color
This parameter allows setting the power value for the yellow backlight of the LED ring.

NOTE
The value of parameter 4 must be between the values of parameters 3  and 5.

5. Measured power for orange LED ring color
This parameter allows setting the power value for the orange backlight of the LED ring.

NOTE
The value of parameter 5 must be between the values of parameters 4  and 6.

6. Measured power for the red LED ring color
This parameter allows setting of power value for the red backlight of the LED ring.

NOTE
The value of parameter 6 must be between the values of parameters 5 and 7.

7. Measured power for violet LED ring color
This parameter allows setting the power value for the violet backlight of the LED ring.

Specifications

– CEE 7/17 – max load 10A
– Dual-type plugs E/F
EU directives compliance:| RED 2014/53/EU RoHS 2011/65/EU
Pollution degree:| 2 (home and office use, indoor only)
Radio protocol:| IEEE 802.11 n Bluetooth° low energy
Radiofrequency:| 2.4 GHz
Transmit power:| 14 dBm (Wi-Fi) 8 dBm (BLE)
Operating temperature:| 0-40°C (32-104°F)
Dimensions (diameter x height):| 43 x 65 mm (1.7″ x2.56″)

Safety classification rating: home and office use only
Type 1 action according to features of automatic action as per clause 6.4.1 of en 60730-1:2012 standard.
Software class A device, according to en 60730-1:2012 standard.

Regulations

Legal Notices
All information, including, but not limited to, information regarding the features, functionality, and/or other product specification are subject to change without notice. Fibaro reserves all rights to revise or update its products, software, or documentation without any obligation to notify any individual or entity.
FiBARO and Fibar Group logo are trademarks of Fibar Group S.A. Apple, iPhone, iPad, iPad Air, and iPod touch are trademarks of Apple inc., registered in the u.S. and other countries. HomeKit is a trademark of Apple inc.
Wi-Fi is a registered trademark of Wi-Fi Alliance.
The Bluetooth word mark is a registered trademark of Bluetooth SiG, inc. All other brands and product names referred to herein are trademarks of their respective holders.
use of the Works with Apple HomeKit logo means that an electronic accessory has been designed to connect specifically to iPod touch, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

Warning
This product is not a toy. Keep away from children and animals!

WEEE Directive Compliance
****Devices labeled with this symbol should not be disposed of with other household wastes. it shall be handed over to the applicable collection point for the recycling of waste electrical and electronic equipment.

Declaration of conformity
****Hereby, Fibar Group S.A. declares that the device is in compliance with Directive 2014/53/eu. The full text of the eu declaration of conformity is available at the following internet address:www.manuals.fibaro.com

References

• Welcome to FIBARO Manuals - FIBARO Manuals

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>