emos P5604 Thermostat Instruction Manual
- June 9, 2024
- EMOS
Table of Contents
P5604 Thermostat
Instruction Manual
View all emos thermostat manual
****www.emos.eu
P5604 Thermostat
The P5604 thermostat is designed for controlling heating and air-conditioning systems.
Important
- Before the first use, make sure to carefully read the Operating Manual for the thermostat, as well as the boiler or air-conditioning equipment.
- Turn off power supply before installing the thermostat!
- Installation should be carried out by a qualified person!
- During installation, follow applicable standards.
Technical specifications:
Switched load: max. 230 V AC; 8 A for resistive load; 2 A for inductive load
Clock accuracy: ±60 seconds/month
Temperature measurement: 0 °C to 40 °C with 0.1 °C resolution accuracy ±1 °C
at 20 °C
Temperature setting: 5 °C to 35 °C in 0.5 °C increments
Temperature differential: 0.2 °C
Operating temperature: 0 °C to 40 °C
Storage temperature: -20 °C to 60 °C
Power supply: 2× 1.5 V AAA batteries
Accessories: 2 screws, 2 wall plugs
Dimensions and weight: 30 × 120 × 75 mm; 125 g
Display Description (See Fig. 1)
- Operating mode
- Cooling mode
- Low battery indicator
- Current set temperature
- Room temperature
- Heating mode
Procedure for Removing the Front of the Thermostat (See Fig. 2)
Display Backlighting
Pressing the control wheel activates display backlighting for 10 seconds.
INSTALLATION
Warning:
Before replacing the thermostat, disconnect the heating/air-conditioning
system from the main power in your flat. This will prevent potential injury by
electric current.
Thermostat Installation
The rear of the thermostat carries 4 openings for mounting onto a wall.
Use the enclosed screws and wall plugs to mount the thermostat.
Wiring Diagram
Voltage connection diagram for connecting thermostat P5604 to a boiler with
“NO” outlet:
Max. 230 V 8(2) A 
* When connecting a
cooling device to the thermostat, connect the “L” phase conductor to the “NC”
terminal.
Zero-voltage connection diagram for connecting thermostat P5604 to a boiler
with “NO” outlet:
Max. 230 V 8(2) A
Putting into Operation
1. Remove the front portion of the thermostat and insert 2× 1.5 V AAA
batteries. Use alkaline batteries only, not rechargeable ones.
2. Replace the front of the thermostat.
3. The thermostat now has an active display and is operational.
If the thermostat is not working properly, please check the polarity of the
batteries, whether they are sufficiently charged, or reset the thermostat by
removing the batteries.
Choosing Operating Mode (Heating, Cooling, Anti-Freeze Temperature)
-
Press and hold the control wheel for 5 seconds to enter mode settings.
-
Turn the control wheel to select one of the following modes:
a. HEAT (heating system)
b. OFF (anti-freeze temperature of 7 °C)
c. COOL (cooling system) -
Press the control wheel to confirm your selection.
Room Temperature Calibration
Press and hold the control wheel for 5 seconds until the setting mode
indicator starts flashing on the screen.
Press and hold the control wheel again for 5 seconds until the temperature
calibration value starts flashing on the screen.
Use the wheel to set the temperature value of choice (-3.0 °C to 3.0 °C, in
0.5 °C steps) and confirm by pressing the wheel.
Room temperature calibration is used if, for example, the thermostat shows 21
°C but you want it to show 20 °C. In that case, the calibration value should
be set to -1 °C.
Upkeep and Maintenance
The product is designed to provide trouble-free service for many years if used properly. Here are some tips for proper operation:
-
Read the manual carefully before using this product.
-
Do not expose the product to direct sunlight, extreme cold and humidity, and sudden changes in temperature. This would reduce the accuracy of detection.
-
Do not place the product in locations prone to vibration and shocks – these may cause damage.
-
Do not expose the product to excessive force, impacts, dust, high temperatures or humidity – these may cause malfunction, shorter battery life, damage to batteries and deformation of plastic parts.
-
Do not expose the product to rain or high humidity, dripping or splashing water.
-
Do not place any open flame sources on the product, e.g. a lit candle, etc.
-
Do not place the product to places with inadequate airflow.
-
Do not insert any objects in the product vents.
-
Do not tamper with the internal electric circuits of the product – doing so may damage the product and will automatically void the warranty.
The product should only be repaired by a qualified professional. -
To clean the product, use a slightly moistened soft cloth. Do not use solvents or cleaning agents – they could scratch the plastic parts and cause corrosion of the electric circuits.
-
Do not immerse the product in water or other liquids.
-
In the event of damage or defect of the product, do not perform any repairs by yourself. Have it repaired in the shop where you bought it.
-
This device is not intended for use by persons (including children) whose physical, sensory or mental disability or whose lack of experience or knowledge prevents them from using it safely. Such persons should be instructed as to how to use the device and should be supervised by a person responsible for their safety. Children must always be supervised and must never play with the device.
Do not dispose of domestic waste. Use special collection points for sorted
waste. Contact local authorities for information about collection points. If
the electronic devices would be disposed on landfill, dangerous substances may
reach groundwater and subsequently the food chain, where it could affect human
health.
WARNING: The contents of this manual may be changed without prior notice
– due to printing limitations, the symbols shown may differ slightly from
those on the display – the content of this manual may not be reproduced
without the manufacturer’s permission. The manual can be found at:
http://www.emos.eu/download.
EMOS P5604 Thermostat Installational Manual
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>