FRACARRO Cascadable 5 Input Switches with Active and Passive TV Gain Instruction Manual
- June 3, 2024
- FRACARRO
Table of Contents
FRACARRO Cascadable 5 Input Switches with Active and Passive TV Gain
SAFETY WARNINGS
The product must only be installed by qualified persons, according to the
local safety standards and regulations. Fracarro Radioindustrie is free from
all civil and criminal responsibilities due to breaches of the current
legislation derived from the improper use of the product by the installer,
user or third parties. The product must be used in full compliance with the
instructions given in this manual in order to protect the operator against all
possible injuries and the product from being damaged.
Don’t open the product case: components under dangerous voltage may be
accessible when the case is opened.
Installation warnings
- The product must not be exposed to any dripping or splashing and thus it should be installed indoors and in a dry location.
- Humidity and condensation could damage the product. In case of condensation, wait until the product is dry before using it.
- Handle the product carefully. Impacts can damage the product.
- Leave enough space around the product to ensure sufficient ventilation.
- Excessive temperatures and/or an overheating may affect the performance and the life of the product.
- Don’t install the product above or near any heat sources, in dusty places or where it might come into contact with corrosive substances..
- In the event that the unit is fixed to the wall, use the proper screw anchors suitable to the characteristics of the fixing support. The wall and the anchoring system must be able to support at least 4 times the weight of the unit.
Warning: to avoid injury, this appliance must be secured to the wall / floor depending on the installation instructions. For “PERMANENTLY INSTALLED APPLIANCES”, an easily accessible cutting device must be added to the exterior of the appliance; for “APPLIANCES WITH A POWER PLUG”, the socket must be installed close to the appliance and easily accessible. The product must be connected to the grounding electrode of the antenna system in compliance with standard EN 60728-11. The screw provided for this purpose is marked with the symbol
It is recommended to comply with the provisions of the standard EN60728-11 and to connect this screw to the main earth node of the plant (do not connect to intermediate points).
Earth screw/Faston connector symbol
Class II symbol
General warnings: In the event of a malfunctioning, do not try to fix the product as the guarantee would be invalidated. Only use the power supply supplied with the product. Although the information given in this manual has been prepared carefully and thoughtfully, Fracarro Radioindustrie S.r.l. reserves the right to modify it without notice and to improve and/or modify the product described in this manual. See the website www.fracarro.com to have information relevant to the technical support and product guarantee.
PRODUCT INSTALLATION
- Use plastic brackets for installing the switch as shown.
- Earthing screw.
Connect the power supply to the DC port (bottom left side) IMPORTANT: use only given PSU1215TS or PSU1340TS, an incorrect voltage (ex. 18V) will damage the product. The voltage has to be within 12V and 14V; if it is used an higher voltage (ex. 18V) the multiswitch will be damaged.
USER’S INSTRUCTIONS
when the product is correctly fed, the voltage is sent to all input satellite ports, allowing to feed the connected LNBs or amplifiers
The TV signal can be adjusted using the dip switch on the top right side of the mechanic; when the TV gain is passive it is not necessary to feed the multiswitch and there is also the return channel.
when the product is correctly fed, the voltage is sent to all input satellite ports, allowing to feed the connected LNBs or amplifiers
The TV signal can be adjusted using the dip switch on the top right side of the mechanic; when the TV gain is passive it is not necessary to feed the multiswitch and there is also the return channel.
OPERATING LEVEL
LED Power ON: if the multiswitch is correctly powered the LED will be ON. If there is a short circuit in the satellite lines, the LED will be OFF; in this case is recommended to disconnect the power supply, remove the short circuit and restore the power supply, the LED will turn ON again.
Taps LED: every tap has a green LED; the LED lights up when a voltage is detected on the port; if the STB is properly connected to the multiswitch, the LED will detect DiSEqC command and it will be ON; otherwise verify the connection quality and the decoder settings.
CONFIGURATION EXAMPLES
TECHNICAL SPECIFICATIONS
|
SWP508TS
|
SWP512TS
|
SWP516TS
|
SWP524TS
|
SWP532TS
|
---|---|---|---|---|---|---
GB: Number of inputs I: Numero d’ingressi| 5| F: Nombre d’entrées
D: Anzahl der Eingänge
GB: Number of outputs I: Numero d’uscite| 8| 12| 16| 24| 32| F: Nombre de sorties
D: Anzahl der Ausgänge
| GB: Bandwidth
I: Larghezza di banda
| 950-2300MHz| F: Bande passante D: Bandbreiten|
GB: Gain
I: Guadagno
| 2dB| 1dB| 1dB| 0dB| 0dB| F: Gain
D: Verstärkung
GB: Uptilt
I: Pendenza
| 4dB| F: Inclinaison D: Uptilt
GB: Max Output level (IM3) I: Livello Max uscita (IM3)| 100dBµV| F: Niveau de
sortie max (IM3) D: Max Ausgangspegel (IM3)
GB: Return loss
I: Perdita di ritorno
| 10dB| F: Perte de retour D: Return loss
| GB: Bandwidth
I: Larghezza di banda
| Active TV: 47-862MHz Passive TV: 5-862MHz| F: Bande passante D: Bandbreiten|
GB: Active Gain
I: Guadagno attivo
| 1dB| 0dB| -1dB| -2dB| -2dB| F: Gain active
D: Aktiver Verstärkung
GB: Passive Gain
I: Guadagno passivo
| -19dB| 20dB| -21dB| -22dB| -22dB| F: Gain passive
D: Passivem Verstärkung
GB: Max Output level (IM3) I: Livello Max uscita (IM3)| Active TV: 92dBµV| F:
Niveau de sortie max (IM3) D: Max Ausgangspegel (IM3)
GB: Return loss
I: Perdita di ritorno
| 10dB| F: Perte de retour D: Return loss
GB: Isolation Output SAT-SAT I: Isolamento Uscite SAT-SAT| 30dB| F: Isolation
sorties SAT-SAT
D: Die entkopplung inputs SAT-SAT
GB: LNB Control I: Controllo LNB| 14V/18V – 0KHz/22KHz – DiSEqC 2.0| F:
Control LNB D: LNB Kontrolle
GB: Tap Consumption I: Consumo Tap| 40mA| F: Consommation Tap D: Tap Verbrauch
GB: Power supply plug
I: Connettore alimentazione
| 2.1x5mm 5x12mm Internal positive, external negative| F: Connecteur
d’alimentation D: Versorgung Verbinder
GB: Consumption I: Consumo| Active TV: 160mA @13V Passive TV: pass| F:
Consommation D: Verbrauch
GB: Max LNB supply I: Max corrente LNB| Active TV: 1340mA @13V Passive
TV:1500mA @13V| F: Max LNB alimentation D: Max LNB-Versorgung
GB: Dimensions I: Dimensioni| 110x
130×40
| 170x
130×40
| 170x
130×40
| 230x
130×40
| 300x
130×40
| F: Dimensions
D: Abmessungen
GB: Operating temperature
I: Temperatura di funzionamento
| -10 to 55 °C| F: Température fonctionnelle
D: Betriebsumgebungstemperatur
GB: The technical data are nominal values and refer to an operating temperature of 25° C.
The technical data are nominal values and refer to an operating temperature of 25° C.
CONFORMITY TO EUROPEAN LAWS
Fracarro declares that the product complies with EU Directive 2014/53 and
2011/65/UE. The full text of the EU Declaration of Conformity is available on
the following website ce.fracarro.com
USER’S INFORMATION
Disposal of Old Electrical & Electronic Equipment (Applicable in the European
Union and other European countries with separate collection
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, wich could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.