RAB Hidfa-XXS-E26-8xx-Byp Post Top Series Instructions

RAB Hidfa-XXS-E26-8xx-Byp Post Top Series

IMPORTANT

READ CAREFULLY BEFORE INSTALLING LED HID BULBS. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB LED HID Bulbs must be wired in accordance with the National Electrical Code and all applicable codes. Proper grounding is required for safety.THIS PRODUCT MUST BE INSTALLED IN ACCORDANCEWrTHTHE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNINGS

• Main applications include for use in post tops, street lights, flood lights and other suitable light fixtures.
• Operating temperature:-30-C to 60″C (-22″F to 140″F).
• These LED Lamps require all ballasts, capacitors, and ignitors to be bypassed or removed. Do not operate lamps on existing ballasts.
• Do not use with standard dimmers.
• This device is not intended for use with emergency exits.
• For use in enclosed fixtures.
• Before installation make certain the AC power to the fixture is off.
• Risk of fire or electric shock. Luminairewiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components.
• Risk of fire or electric shock. LED Retrofit lamp Installation requires knowledge of lumlnaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• Installers should not disconnect existing wires from lampholderterminals to make new connections at lampholderterminals. Instead installers should cut existing lampholder leads away from the lampholder and make new electrical connections to lampholder lead wires by employing applicable connectors.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
• Use only with a portable luminairethat is provided with a shade.
• Added weight of the device may cause instability of a free-standing portable luminaire.
• THIS RETROFIT KIT IS ACCEPTED ASA COMPONENT OF A LUMINAIREWHERETHE SUITABILITY OFTHE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION.
• Please examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.
• RISK OF FIRE OR ELECTRIC SHOCK. INSTALLATION OFTHIS RETROFIT KIT REQUIRES A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OFTHE LUMINAIRE’S ELECTRICAL SYSTEM AND THE HAZARD INVOLVED. IF NOT QUALIFIED, DO NOT ATTEMPT INSTALLATION. CONTACT A QUALIFIED ELECTRICIAN.

INSTRUCTIONS POSTTOP SERIES

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

LAMP INSTALLATION

1. Turn off the power before installation. Remove old ballast or disconnect from existing lampholder. Shown as Figure 1. Remove and dispose of ballast in correct manner. (North America 100-277VAC)
2. Reconnect directly to the existing lampholder. Shown as Figure 2 (North America 100-277VAQ
3. Select power and color temperature (CCT) of new LED replacement lamp before installation.
4. Install new LED replacement lamp. Shown as Figure 3. Please make sure the old fitting is correctly grounded. Attach retrofit label to luminaire. (North America 100-277VAC)

Securely fasten the ground wire to the main body structure. If the wire is damaged in any way please replace. (Do not use existing burnt out wire). If needed, the replacement ground wire must be 1.0mm in size and insulated from heat.

Note: These instructions do not cover a fl details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.

SELE CTAB IL ITV Power Selectable

SELE CTAB IL ITV Power and CCT Selectable

rabllghting.cam Tech Help Line e-mail Free Lighting Layouts Cnnbury,NlwJlrHYOl512:USA Visit our website for product Info Call our experts: 888 722-1000 Answered promptly- sales@rabllghtlng.com Answered onllne or by request RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty. RAB L1ght1ng Is committed to creating h1gh- qualrty, affordable, well-designed and energy-efficient LED l1ght1ng and controls that make 1t easy for electricians to install and end users to save energy We’d love to hear your comments Please call the Marketing Department at 888-RAB-1000 or email market1ng@rabhght1ng.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>