INVACARE Versatile Dragon Power Wheelchair Instructions
- June 9, 2024
- INVACARE
Table of Contents
INVACARE Versatile Dragon Power Wheelchair
Frame type
Identify chair’s frame type and then select compatible mounting hardware for belts and harnesses.
Mounting solution for chairs with sling seat upholstery or a solid seat base.
90° bend for top mounting on seat tubes (pictured at right), or a 20 bend tor
side mounting. Sold in pairs.
Directly mount belts or harnesses to power wheelchair-slotted rails. ómm size
for Permobil chairs, or 10mm size for Invacare and Pride/ Quantum chairs
.
MOUNTING HARDWARE
Band Clamp
Frame types: A, B, C
Flexible stainless spring steel fits into tight gaps under seats on a wide
variety of frames. Useful for mounting where there are no pre- existing holes.
Sold in pairs.
- HW320-22-2 Ø22mm (7/8″)
- HW320-25-2 025mm (1″)
- HW320-27X33-2 27 x 33mm (1-1/16″ x 1-5/16″), oval
- HW320-29-2 D29mm (1-1/8″)
- HW320-30-2 030mm (1-3/16″)
- HW320-32-2 32mm (1-1/4″)
FrameSaver” Clamp & Shim
Frame type: A
Strong, durable nylon cdamps snap onto tubing and won’t scratch Surtace. Our
most affordable clamp, the Framesaver is pertect when clearance is not an
issue. Fits 025mm (1 “) tubing, and 22mm (7/8″) tubing with enclosed shim. Can
also be used on 019mm (3/4”) tubing with 19mm shim, sold separately Sold in
pairs.
- HW303-B-2 25mm clamp + 22mm shim
- HW303-19SHIM-2 19mm shim
Hardware Gauge
This indispensable tool for measuring tubing diameter helps you choose the
correct mounting hardware. Its also an easy way to select correctly-sized
screws and nuts for a particular wheelchair. BMR-42
Frame Clamp
Frame types: A, C
Open-jaw design fits underneath seat upholstery and armrest pads. Made with
sturdy, two-piece aluminum construction. Sold in pairs.
NEW! Evoflex° Belt Extender
Made of high-impact plastic, the Evoflex Belt Extender maintains the stiffness
of the Evoflex while lengthening the belt up to 12.5 cm (5″). Perfect for
mounting to wheelchairs with thicker cushions, deeply contoured seating, or
distant mounting points. Available separately or bundled with the Evoflex
belt.
Cam Buckles
Convenient end-sitting option for evaluation setting or whenever temporary
fittings are needed. Also suitable for long-term use with chest or shoulder
harnesses on users up to 75kg. Mount to solid backrest or Strap Guides. D6mm
(1/4″) hole. Sold in pairs.
- FS032-2 Fits 2.5cm (1″) wide webbing belts & harnesses
- FS033-2 Fits 4cm (1-1/2″) wide webbing belts
- FS034-2 Fits 5cm (2″) wide webbing belts
Shoulder Harness Strap Guides
Improve positioning and comfort of chest and shoulder harnesses by optimizing
height and angle of top straps.
SIZING
How to Measure for a Padded Hip Belt
To ensure proper fit and best performance, always select the padded belt size
that best fits the user. When working with the Evoflex, consider adding Belt
Extenders if longer straps are needed to reach the desired mounting point (see
right)
Determine the correct belt size for the user:
- Based on clinical goals, use arms to place user in desired position and determine the most effective position and angle for the belt.
- At the selected belt angle, measure the distance over the body with a flexible tape to find the optimal length for the belt’s padded section.
- In the sizing table for your belt style, refer to Column B to find the appropriate belt size based on padded length. If user is between sizes, consider factors such as growth, weight variations and clothing changes. For proper fit and function, pads should not extend past the user’s body.
Two-Point and Four-Point Padded Hip Belts
Additional Instructions for the Evoflex
Determine total length needed for mounting:
- At the selected belt angle, measure from the mounting point on one side across the user’s body to the mounting point on the other side.
- In the Evoflex sizing table, refer to Column D to find the maximum mounting length for the selected size belt.
- lf belt will not be long enough to reach the mounting points, Evotlex Belt Extenders can be used to add up to 12.5 cm (5) per side. See the Evoflex + Belt Extender table below for maximum combined length. Both the Evoflex Belt and Belt Extender can be cut to length if needed. See p. 10 for Belt Extender details.
Evoflex
Evoflex +Belt Extender
Leg Harnesses
Measure from the anterior superior iliac spine (ASIS) to the point where the
inner thigh touches the seat.
Non-Padded Hip Belts
Stayflex, PivotFit and Trimline
Measure the maximum width across the shoulders, at the deltoid muscles.
Calf Supports (Calf Strap and Calf Panel)
Measure the curved distance around the legs from the outside of the
wheelchair. Choose a size with enough length for the pad to flex and wrap
behind calves.
Monoflex” Chest Supports
Measure the trunk around the front and sides at the height at which the
MonoflexTM will be worn.
Ankle Huggers
Measure circumference above ankle.
Additional sizing information can be found in the product listings throughout this Product Guide and on www.bocypoint.com.
TERMS AND CONDITIONS
LIMITED LIFETIME WARRANTY
Most products manufactured by Bodypoint ca rry a limited lifetime warranty
against defects in workmanship and materials arising under normal use by the
original consumer. Product specifications are subject to change. For current
specifications and warranty details, contact your local Independent
Distributor or contact Customer Service at
sales@bodypoint.com or
1-800-547-5716.
LIMITATIONS ON WARRANTIESS
The warranties described herein do not extend to nomal wear and tear; to
products that have been subject to misuse, accident or tampering; nor to
products that have been modified in any way other than that specifically
described in the product instructions. Normal wear and tear is damage that
naturally and inevitably occurs as a result of typical use. Purchaser’s sole
remedy for defective products shall be repair, replacement or account
adjustment at the discretion of Bodypoint. In all circumstances Bodypoint
reserves the right to substitute an equivalent product or refund the purchase
price of the original product.
THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL BODYPOINT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL LOSSES OR DAMAGES RESULTING FROM THE USE OF THE PRODUCT, INCLUDING WITHOUT LIMITATION, LOSS OF ANTICIPATED PROFITS, EVEN IF BODYPOINT SHALL HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH POTENTIAL LOSS OR DAMAGE. BODYPOINT SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE CAUSED BY DELAY IN FURNISHING PRODUCT.
Bodypoint does not authorize any distributor, dealer, agent, sales person or any third party to change the terms or coverage of this warranty, and any such change shall be null and void. This warranty is non-transterable. This warranty will be governed in accordance with the laws of the State of Washington. The customer consents that jurisdiction under Venue for any action shall be in King County Washington. This warranty information is reprinted here for information purposes only and is subject to change without notice.
TERMS
Standard terms are net 30 days on accounts approved for credit. Any returned
check will incur a $50 service charge. We also accept Visa, MasterCard, or
American Express. All shipments are FOB Seattle, Washington. Product
specifications, prices, terms and conditions are subject to change without
notice. Contact Customer Serviceat
sales@bodypoint.com or
1-800-547-5716 for further details.
PAST DUE ACCOUNTS
Past due invoices will incur finance charges at the rate of 1.5% per month.
Bodypoint reserves the right to hold shipments or require prepayment for any
delinquent account.
RETURNS
All returns must be pre-authorized by Bodypoint. Customer must contact
Bodypoint within 30 days of the purchase date for a return authorization. All
returns are subject to a 15% restocking fee, plus applicable freight charges.
TRADEMARK INFORMATION
- Bodypoint and the Bodypoint Logo are registered trademarks of
- Bocypoint, Inc. in Canada, China, the EU, India and the USA
- Strengthen Your Position is a registered trademark of Bodypoint, Inc. in the EU and USA.
- Ankle Huggers is a registered trademark of Bodypoint, Inc. in Canada, the EU and the USA.
- Aeromesh is a registered trademark of Bodypoint, Inc. in the EU and the USA.
- Evoflex is a registered trademark of Bodypoint, Inc. in the USA.
- Cinch-Mount, Flat-Mount, FrameSaver, Stayflex, Laminar Pad, Monoflex,
- Rehab Latch, PivotFit, MD Series, and MD Pull Straps are all trademarks of Bodypoint, Inc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>