LeDj Spectra Par 12HEX10 PRO Exterior Fixture User Manual

June 9, 2024
LeDj

LeDj Spectra Par 12HEX10 PRO Exterior Fixture

WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP!

  • Before your initial start-up, please make sure that there is no damage caused during transportation.
  • Should there be any damage, consult your dealer and do not use the equipment.
  • To maintain the equipment in good working condition and to ensure safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this manual.
  • Please note that damages caused by user modifications to this equipment are not subject to warranty.

CAUTION!
TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorised modification to the equipment.

  • Never let the power cable come into contact with other cables. Handle the power cable and all mains voltage connections with particular caution!
  • Never remove warning or informative labels from the unit.
  • Do not open the equipment and do not modify the unit.
  • Do not connect this equipment to a dimmer pack.
  • Do not switch the equipment on and off in short intervals, as this will reduce the system’s life.
  • Do not expose to flammable sources, liquids or gases.
  • Always disconnect the power from the mains when equipment is not in use or before cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the power-cable.
  • Make sure that the available mains supply voltage is between 100~240V AC, 50/60Hz.
  • Make sure that the power cable is never crimped or damaged. Check the equipment and the power cable periodically.
  • If the equipment is dropped or damaged, disconnect the mains power supply immediately and have a qualified engineer inspect the equipment before operating again.
  • If your product fails to function correctly, stop use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Pro Light dealer for service.
  • Only use fuses of same type and rating.
  • Repairs, servicing and power connection must only be carried out by a qualified technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
  • This lighting fixture is for professional use only – it is not designed for or suitable for household use. The product must be installed by a qualified technician in accordance with local territory regulations. The safety of the installation is the responsibility of the installer. The fixture presents risks of severe injury or death due to fire hazards, electric shock and falls.
  • Warning! Risk Group 2 LED product according to EN 62471. Do not view the light output with optical instruments or any device that may concentrate the beam.
  • WARRANTY: One year from date of purchase.

OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and/or property.

Spectra Par 12HEX10 PRO

The exterior Spectra Par 12HEX10 features 12 x 10W six-colour LEDs, delivering a smooth wash of colour, ranging from intense, rich saturated hues through to pastel shades. Controllable via the onboard 4 button LED menu system for auto, static colour or master/slave modes, with the option of DMX control for larger installations. The silent running, convection cooled heavy-duty alloy enclosure features TRUE1 and 5-Pin DMX inputs and outputs to facilitate a problem-free, rental ready connection.

  • 12 x 10W six-colour LEDs (RGBWAUV)
  • Beam angle: 28°
  • 4,374 Lux @ 2m (full on)
  • 1kHz refresh rate
  • DMX channels: 6, 8 or 10 selectable
  • Static colour, colour change, colour fade and master/slave modes
  • 0 – 100% dimming and variable strobe
  • Bracket allows for multiple rigging or floor standing applications
  • Quick release omega clamp included
  • 4 push button menu with LED display
  • PowerCON TRUE1 compatible Seetronic input/output
  • IP rated 5-Pin XLR input/output
  • Convection cooled
Specifications Spectra Par 12HEX10 PRO
Power consumption 130W
Power supply 100~240V, 50/60Hz
Dimensions 327 x 308 x 139mm
Weight 4.53kg
Order code LEDJ283A

LeDj-Spectra-Par-12HEX10-PRO-Exterior-Fixture-2

  1. Bracket
  2. Bracket tightening knobs
  3. LED display
  4. Function buttons
  5. IP rated 5-Pin DMX input
  6. IP rated 5-Pin DMX ouput
  7. PowerCON TRUE1
  8. PowerCON TRUE1 power ouput
  9. Pressure relief valve

In the box:

  • 1 x fixture,
  • 1 x power cable &
  • 1 x user manual

Operating instructions

IMPORTANT! PLEASE NOTE: The LED display for this fixture has a menu locking function where after 30 seconds of inactivity it will lock. To unlock the menu hold the “MODE” and
“DOWN” buttons for 3 seconds.

DMX channel mode:
Operating in a DMX control mode environment gives the user the greatest flexibility when it comes to customising or creating a show. In this mode you will be able to control each individual trait of the fixture and each fixture independently.
To access the DMX channel mode, press the “MODE” button on the rear of the unit to show d001 on the LED display. Now use the “UP” and “DOWN” buttons to set the desired DMX address. Now press the “SETUP” button to choose one of the 6, 8 or 10 DMX channel modes, press the “SETUP” button to confirm the setting. To exit out of any of the above options, press the “MODE” button.

6 channel mode:

Channel Value Function
1 000-255 Red (0-100%)
2 000-255 Green (0-100%)
3 000-255 Blue (0-100%)
4 000-255 White (0-100%)
5 000-255 Amber (0-100%)
6 000-255 UV (0-100%)

8 channel mode:

Channel Value Function
1 000-255 Master dimmer (0-100%)
2 000-255 Red (0-100%)
3 000-255 Green (0-100%)
4 000-255 Blue (0-100%)
5 000-255 White (0-100%)
6 000-255 Amber (0-100%)
7 000-255 UV (0-100%)
8 000-255 Strobe (slow-fast)

10 channel mode:

Channel| Value| Function|
---|---|---|---
1| 000-255| Master dimmer (0-100%)|
2| 000-255| Red (0-100%)|
3| 000-255| Green (0-100%)|
4| 000-255| Blue (0-100%)|
5| 000-255| White (0-100%)|
6| 000-255| Amber (0-100%)|
7| 000-255| UV (0-100%)|
| 000| No function|
| 001-020| Program 1|

When 001-020

use CH9 for static colours.

When 021-255

use CH9 for speed (slow-fast)

|
| 021-041| Program 2|
| 042-062| Program 3|
| 063-083| Program 4|
| 084-104| Program 5|
8| 105-125| Program 6|
| 126-146| Program 7|
| 147-167| Program 8|
| 168-188| Program 9|
| 189-209| Program 10|
| 210-230| Program 11|
| 231-255| Program 12|
| 000| No function| |
| 001-016| Red| |
| 017-033| Green| |
| 034-050| Blue| |
| 051-067| White| |
| 068-084| Amber| |
| 085-101| UV| |
| 102-118| Orange| Speed|
9| (slow-fast)

when CH8 is

|
119-135| Yellow|
136-152| Magenta|
| 021-255|
| 153-169| Hot Pink| |
| 170-186| Cyan| |
| 187-203| Pastel Red| |
| 204-220| Pastel Green| |
| 221-237| Pastel Blue| |
| 238-254| Warm White| |
| 255| Cool White| |
10| 000-255| Strobe (slow-fast)|

Built-in program mode:
To access the built-in program mode press “MODE” until the display shows Pr.01 on the LED display. Press “SETUP” to confirm the setting. Use the “UP” and “DOWN” buttons to select a program from  Pr.01 ~ Pr.12. Press the “SETUP” button to confirm the setting.
o change the speed of the selected program press the “SETUP” button and then use the “UP” and “DOWN” buttons to select any value from SP00 ~ SP99. Press the “SETUP” button to confirm the setting, then use the “UP” and “DOWN” buttons to select and value from F500 ~ F599 for the strobe feature. Press the “SETUP” button to confirm the setting.
In Pr.01 you are able to set a specific static colour. When in Pr.01 press the “SETUP” button and then use the “UP” and “DOWN” buttons to go through the static colours. Press the “SETUP” button to confirm the setting, then use the “UP” and “DOWN” buttons to select and value from F500 ~ F599 for the strobe feature. Press the “SETUP” button to confirm the setting.
To exit out of any of the above options, press the “MODE” button.

Programs:

Pr.01 Static colour
Pr.02 6 colour fade in/out
Pr.03 Colour fade in/out
Pr.04 Colour fade
Pr.05 6 colour change
Pr.06 Colour change
Pr.07 Red continuous fade
Pr.08 Green continuous fade
Pr.09 Blue continuous fade
Pr.10 White continuous fade
Pr.11 Amber continuous fade
Pr.12 UV continuous fade

Static colours:

0.Off – Blackout

1.–r – Red
2.–g – Green
3.–b – Blue
4.–u – White
5.–A – Amber
6.–I – UV

7.-rg – Orange
8.-rg – Yellow
9.-rb – Magenta
10.-rb – Hot Pink
11.-gb – Cyan
12.-ru – Pastel Red

13.-gu – Pastel Green
14.-bu – Pastel Blue
15.-uu – Warm White
16.-cu – Cool White

Master/slave mode:
To set the master unit, press the “MODE” button on the rear of the master unit then select your desired program (sound active, auto, static colour or one of the built-in programs). To set the other units in slave mode, press the “MODE” button on the rear of the unit to show SLAu on the LED display and press the “SETUP” button to confirm the setting. The units will now run in sequence with the master unit.
To exit out of any of the above options, press the “MODE” button.
Please ensure that all slave units are set to the same DMX channel mode as the master unit.

Auto mode:
To access the auto mode press “MODE” until the display shows Auto on the LED display. The fixture will now run through its built in programs Pr.02 ~ Pr.12. To exit out of any of the above options, press the “MODE” button. NOTE: The user can set up the speed and flash speed for Pr.02 ~ Pr.12 under the built in programs mode. Changing this here will then take effect when running auto mode.

RGBWAUV colour mix mode:
To access the static colour mode press “MODE” until CoLr shows on the LED display.
Now press the “SETUP” button and use the “UP” and “DOWN” buttons to select the brightness between r.000 ~ r.255. Press the “SETUP” button and repeat for green (G), blue (b), white (u) , amber (A) and UV ( I).
Value: 000 – 255 (000 = low brightness, 255 = high brightness)
To exit out of any of the above options, press the “MODE” button.

Factory reset:
To reset the fixture to factory settings, power the fixture off. Press and hold the “MODE” and “SETUP” buttons whilst powering the unit up. Keep hold of the “MODE” and “SETUP” buttons for 3 seconds after power up. The unit will now have reset to factory settings.

Menu system

Built-in program| Pr.01 Static colour

Pr.02 6 colour fade in/out Pr.03 Colour fade in/out Pr.04 Colour fade

Pr.05 6 colour change

Pr.06 Colour change

Pr.07 Red continuous fade Pr.08 Green continuous fade Pr.09 Blue continuous fade Pr.10 White continuous fade Pr.11 Amber continuous fade Pr.12 UV continuous fade SP00~SP99 (speed) F500~F599 (flash)

---|---
RGBWAUV colour mix mode| r.000~r.255 Red g.000~g.255 Green b.000~b.255 Blue u.000~u.255 White A.000~A.255 Amber I.000~I.255 UV
Auto mode| AUTO
Slave mode| SLAu
DMX mode| 6CH, 8CH, 10CH
Address setting| d.001~d.512

DMX setup

Setting the DMX address:
The DMX mode enables the use of a universal DMX controller. Each fixture requires a “start address” from 1- 512. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address. For example, a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, 105 and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in the chain starts at 107.

DMX 512:
DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a data “out” terminal).

DMX linking:
DMX is a language allowing all makes and models of different manufactures to be linked together  and operate from a single controller, as long as all fixtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be placed anywhere in
a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.

DATA cable (DMX cable) requirements (for DMX operation):
This fixture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit. Your unit requires either a standard 3-pin or 5-pin XLR connector for data input/output, please check the fixtures specifications as to which your unit accepts.LeDj-Spectra-Par-12HEX10-PRO-Exterior-
Fixture-5

Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight Concepts dealers.
Please quote: 3-Pin: CABL10 – 2m CABL11 – 5m CABL12 – 10m
5-Pin: CABL185 – 2m CABL187 – 5m CABL188 – 10m

Also remember that DMX cable must be daisy chained and cannot be split.
Note: To maintain IP65 rating, IP rated DMX cables must de used.

Notice:
Be sure to follow the diagrams below when making your own cables. Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing. Grounding the shield could cause a short circuit and erratic behaviour.

Pin Configuration

3-Pin| 5-Pin
Pin 1 – Ground
Pin 2 – Negative
Pin 3 – Positive
–| Pin 4 – N/C
–| Pin 5 – N/C

LeDj-Spectra-Par-12HEX10-PRO-Exterior-Fixture-6

Line termination:
When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behaviour.
Using a cable terminator will decrease the possibilities of erratic behaviour. (3-pin – Order ref: CABL90, 5-pin – Order ref: CABL89)

5-pin XLR DMX connectors:
Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.

LeDj-Spectra-Par-12HEX10-PRO-Exterior-Fixture-8

Multiple fixture power linking

Power linking:
This fixture provides power linking via the power output on the rear allowing multiple units to be connected together. The maximum number of fixtures that can be connected is 12 fixtures @ 240V or 6 fixtures @ 120V (including the first fixture). After the maximum number of fixtures are
connected a new power run will need to be started.
Please note: Caution should be used when power linking other fixtures to the Spectra Par 15Q8 PRO as the power consumption of other fixtures will vary. LED fixtures fitted with switch mode power supplies often require 2/3 times more current on startup, these may require their own power source.

LeDj-Spectra-Par-12HEX10-PRO-Exterior-Fixture-9

WEEE notice

Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed of with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

www.prolight.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals