LANCOM R&S UF-60 LTE Desktop Unified Firewall User Guide

LANCOM R&S UF-60 LTE Desktop Unified Firewall

OVERVIEW

1. Connection socket for power supply
   After connecting the power supply cable to the device, turn the screwcap clockwise to prevent the jack from accidental unplugging.
   Use only the supplied power adapter.

2. Power button
   Press the power button to start up the device.
   To power off the device, press the power button for 5 seconds.

3. USB 3.0 interfaces
   Interfaces for device software re-installation

4. Reset button
   Short press – device restart

5. Serial configuration interface RJ45 (Console)
   Maintenance interface for expert configuration

6. TP Ethernet interface ETH0 (WAN)
   Connect the ETH0 TP Ethernet interface to other network components. This interface is recommended for Internet access.
   Please refer to the corresponding product supplement for instructions on initial commissioning.

7. TP Ethernet interfaces ETH1 – ETH3 (LAN)
   Connect the ETH1 – ETH3 TP Ethernet interfaces with the enclosed
   Ethernet cable to other networking components.
   Please refer to the corresponding product supplement for instructions on initial commissioning.

8. SIM card slot
   Slide the SIM card into the SIM card slot using the marker to ensure that the card is the right way round. Ensure that the SIM card clicks into place on insertion. To remove the card from the device, press the card lightly into the device.
   Let go to release the SIM card from the slot.

9. LTE antenna connectors ANT1, ANT2
   Connect the supplied cellular antennas to the connectors ANT1 and ANT2.

MOUNTIN GAND CONNECTING THE DEVICE

LEDs ETH0 – ETH3 – TP Ethernet

Upper LEDs – link activity

• Off No link detected
• Green, permanently Link detected, no port activity
• Green, blinking Link detected, port activity

Lower LEDs – link speed

• Off Link speed 10 Mbps
• Orange, permanently Link speed 100 Mbps
• Green, permanently Link speed 1000 Mbps

LEDs Power / HDD / LTE

• Power off Device switched off
• Power green Device operational
• HDD off No HDD read-/write access
• HDD blue, flickering HDD read-/write access
• LTE off Mobile radio interface switched off
• LTE green, permanently Mobile radio connection active

LED Power switch

• Off No power supply connected
• Red, permanently Device switched off, power supply connected
• Blue, permanently Device switched on

LEDs ETH0 – ETH3 – TP Ethernet

• Both off Gerät ausgeschaltet oder
  kein Netzwerkgerät angeschlossen

• Left green, flickering  Data transfer 1000 Mbps
  Right green,permanently

• Left green, flickering    Data transfer 100 Mbps
  Right orange,permanently

• Left green, flickering  Data transfer 10 Mbps
  Right off

Hardware

• Power supply 12 V DC, external power supply
• Power consumption Max. 40 W
• Environment Temperature range 0–40 °C; humidity 10–85 %, non-condensing
• Housing Robust metal housing, network connectors on the front
• Dimensions (mm) 232 x 44 x 115 (W x H x D)

Interfaces

• ETH 4x 10 / 100 / 1000 Mbps Gigabit Ethernet ports

• USB 2x USB 3.0 ports
  LTE Two SMA connectors for the supplied dipole rod antennas, compatible LANCOM AirLancer antennas for LTE, 4G, or from other manufacturers. Please respect the restrictions which apply
  in your country when setting up an antenna system (particularly antenna gain/transmission power).

• Console RJ45 configuration interface

Declaration of conformity
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc

Package content

• Documentation Quick Reference Guide (DE, EN), Quick Install Guide (DE/EN), Service & Support Guide (DE/EN)
• Accessories Two LTE/4G antennas, 1 power supply unit with IEC power cable, 1 Ethernet cable, 1 set adhesive rubber pads

Please observe the following when setting up the device

• The mains plug of the device must be freely accessible.
• Do not rest any objects on top of the device and do not stack multiple devices.
• If present, keep all ventilation slots clear of obstruction.
• Mount the device into a 19” unit in a server rack using the separately available rack mount.

Before initial startup, please make sure to take notice of the information regarding the intended use under www.lancom-systems.com/safety!
Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.

LANCOM, LANCOM Systems, LCOS, LAN community and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document
contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and / or omissions. 111989/12/21

References

• DoC - LANCOM Systems GmbH
• lancom-systems.com/safety

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>