RAB FFLED Slipfitter Mount Instruction Manual
- June 8, 2024
- RAB
Table of Contents
RAB FFLED Slipfitter Mount Instruction Manual
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining
fixture. No user serviceable parts inside.
WARNING: RISK OF SERIOUS INJURY OR DEATH!
DO NOT MOUNT THE SLIPFITTER TO A TENON OR BRACKET THAT IS MORE THAN 20 DEGREES
FROM VERTICAL. MOUNTING AT ANY ANGLE OTHER THAN 0-20 DEGREES INCREASES THE
RISK OF DISENGAGEMENT AND/OR FAILURE OF THE SLIPFITTER. INSTALL THE POLE ON A
SECURE BASE OR INSTALL THE BRACKET TO A WALL FIRST. THEN PLACE LUMINAIRE ONTO
THE POLE OR BRACKET. DO NOT LIFT LUMINAIRE ASSEMBLED TO POLE OR BRACKET.
LUMINAIRE MAY DISENGAGE.
SLIPFITTER MOUNTING
- The Slipfitter Mounting fits a 2 3/8” O.D. Tenon. Place the Slipfitter over the Tenon and secure the fixture with the Set Screws on the side of the Slipfitter.
- To adjust the angle of the Slipfitter, remove Screws and Plug on Round Cover Plate. Remove the Round Cover Plate. Loosen the Locking Bolt and adjust the angle of the fixture as desired.
- Feed supply wires from Tenon to Slipfitter and make necessary connections in the Slipfitter and knot wires for strain relief.
- Tighten the Locking Bolt and re-attach Round Cover Plate. Seal Plug on side of Round Cover plate with Teflon Tape or silicone sealant.
TRUNNION MOUNTING
CAUTION: UL and C-UL listed or CSA certified liquid tight cord grip suitable for use with STW flexible cord shall be used for connection to a wet location outlet box provided by others.
To adjust the angle of the fixture using the Trunnion:
- Loosen the Pivot Bolts & angle locking screw.
- Adjust fixture to desired angle.
- Tighten Pivot Bolts & angle locking screw.
0-10V DIMMABLE WIRING
Universal voltage driver permits operation at 120V thru 277V, 50 or 60 Hz. For 0-10V Dimming follow the wiring directions shown below.
- Connect the black fixture lead to the (+) LINE supply lead.
- Connect the white fixture lead to the (-) COMMON supply lead.
- Connect the GROUND wire from fixture to supply ground. Do NOT connect the GROUND of the dimming fixture to the output.
- Connect the purple fixture lead to the (V+) DIM lead.
- Connect the pink (or gray) fixture lead to the (V-) DIM lead.
- Cap the yellow fixture lead, if present. Do NOT connect.
SURGE PROTECTOR OPTION
Units ordered with (/SP) suffix are provided with 10kV surge protector secured within the fixture. Follow wiring directions as shown below .
- Connect the black fixture lead to the LINE supply lead and black surge protector wire.
- Connect the white fixture lead to the COMMON supply lead and white surge protector wire.
- Connect the GROUND wire from fixture to supply ground and green surge protector wire.
- Connect the purple fixture lead to the (V+) DIM lead.
- Connect the pink (or gray) fixture lead to the (V-) DIM lead.
NOTE: Do not connect DIM V+ (purple)/ DIM V- (pink/gray) to line voltage
or supply ground.
Note: These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during
installation, operation or maintenance.
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.
- Lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Do not use chemicals to clean fixture.
- Do not open the fixture to clean the LED. Do not touch the LED.
TROUBLESHOOTING
- Check that the line voltage at the fixture is correct. Refer to wiring directions.
- Is the fixture grounded properly?
- Is the photocell, if used, functioning properly?
Support
RAB Lighting is committed to creating high-quality, affordable, well designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly – sales@rablighting.com
Free Lighting Layouts
Answered online or by request
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found
at rablighting.com/warranty
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>