GoodEarth 18 Inch Color Selectable Under Cabinet Light with Plant Grow Mode Installation Guide

GoodEarth 18 Inch Color Selectable Under Cabinet Light with Plant Grow Mode

Product Overview

Hardware kit

Required

READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!

WARNINGS AND CAUTIONS

WARNING: TO AVOID ELECTRIC SHOCK, DISCONNECT POWER BEFORE INSTALLING

WARNING: DO NOT attempt to alter the fixture. The fixture is not manufactured with parts that are serviceable or replaceable.
WARNING: BURN HAZARD! The fixture can be hot, allow cooling time prior to touching.
WARNING: DO NOT ALTER THE PLUG OR CORD. The fixture uses a grounded plug (2 contact blades and a grounding prong) to reduce the risk of electric shock. The plug is designed to fit ONLY into a grounded electrical outlet. DO NOT defeat this safety feature.
WARNING: Products should be installed following these instructions, local electrical codes and/or the current National Electric Code (NEC). Electrical requirements can be found on back of fixture.
WARNING: DO NOT use an extension cord. ONLY use power strips with integral over current protection.
WARNING: DO NOT look directly at LED light source for any extended period of time.

CAUTION: ONLY operate in areas with air temperatures ranging between -0°F to 104°F (-18°C to 40°C).
CAUTION: ONLY route and secure the cords in a manner where they will not be pinched or damaged. DO NOT hang items from cords.
CAUTION: DO NOT mount to surfaces with a thickness less than 1/4 in DO NOT mount over sinks or stoves.
CAUTION: DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT. This fixture is not dimmable.
CAUTION: DO NOT leave bare wires exposed

Turn power off before servicing.
Indoor use only.
Suitable for damp locations

If unsure if the electrical box is properly grounded, or the box is plastic and has no ground wire, or are unfamiliar with the methods of properly grounding fixture, consult a qualified electrician.

PLUG-IN INSTALLATION

For hardwiring installation, please go to page 2.

WARNING: DO NOT ATTEMPT TO INSTALL LED LIGHT BAR WHILE PLUGGED IN.

1A WOOD

WOOD INSTALLATION: Place fixture in mounting location to mark locations of  mounting holes. Using a small drill or nail, make two small pilot holes at the marked locations. NOTE: Ensure mounting location is within 5 ft of an electrical outlet. Hold the fixture in the marked location and drive short screws (A) until they contact the bottom surface of the cabinet. The short screws (A) must be driven in straight for the fixture to mount properly. DO NOT OVERTIGHTEN to prevent stripping the screw hole. Plug fixture into an electrical outlet.

1B DRYWALL

DRYWALL INSTALLATION: Place fixture in mounting location to mark locations of mounting holes. NOTE: Ensure mounting location is within 5 ft of an electrical outlet. Use a 1/4 in drill bit to drill out the mounting holes for the drywall anchors (B). Pinch the drywall anchor tips together, insert them into the mounting holes, push in until fully inserted and flush with the mounting surface. Drive the long screws (C) into the anchors (B) to securely fasten them into the mounting surface. Plug fixture into an electrical outlet.

HARDWIRE INSTALLATION

For plug-in installation, please go to page 1

**** TURN POWER OFF AT BREAKER BOX/FUSE BOX. TURN WALL SWITCH OFF

1. Remove the access cover by loosening the locking screw and slide the keyhole slot over the screw head, until it reaches to the large end of the keyhole slot. As the access cover is removed from the fixture, the ends of the wires/wire connectors will be pulled out with it. Carefully pull the ends of the wires out.
2. Determine which corresponding knock-out is closest to the supply wire feed and remove it. WITH SOME FORCE, CAREFULLY REMOVE THE KNOCK-OUT WITH A FLAT HEAD SCREW DRIVER OR UNTIL THE SURFACE BREAKS. If the knock-out did not break free, use pliers and bend it back and forth until it snaps off.
3. Attach the strain relief (E) by inserting the threaded end through the knock-out. Secure the strain relief (E) to the fixture by tightening the fastener to the threaded tube. NOTE: Remember to have the strain relief (E) screws oriented in a manner that allows tightening/loosening of the clamp after the fixture has been attached to the mounting surface.
4. Insert a flexible whip or NM cable (not included) through the strain relief (E) and tighten the clamp until it is secure. Allow enough wire length to make the connection. WARNING: Make sure the POWER is OFF.
5. For safety and proper operation, the fixture must be properly grounded. If unfamiliar with the methods of properly grounding the fixture, consult a qualified electrician. A copper ground wire is pre-attached to the fixture. If the electrical box is made of plastic and/or has a green or bare copper grounding wire inside, the fixture grounding wire and the electrical box ground wire should be connected using one of the wire nuts (D). If the fixture is being connected using a flexible whip or NM cable, the fixture grounding wire and the electrical supply ground wire should be connected using one of the wire nuts (D). Connect the supply leads to the fixture wire leads using the supplied wire nuts (D). The black leads from the fixture go to the black supply lead and the white leads from the fixture go to the white supply lead. Tighten the wire nuts (D) properly to prevent the wires from coming loose. If unsure of tightness, tape the wire nuts (D) to the wire using electrical tape. Carefully push any excess wiring back inside the fixture.
6. Push excess wire back into the wire compartment in the fixture. Re-attach the access cover to the fixture.
   

1A WOOD

WOOD INSTALLATION: Place fixture in mounting location to mark locations of mounting holes. Using a small drill or nail, make two small pilot holes at the marked locations. Hold the fixture in the marked location and drive short screws (A) until they contact the bottom surface of the cabinet. The short screws (A) must be driven in straight for the fixture to mount properly. DO NOT OVERTIGHTEN to prevent stripping the screw hole.

1B DRYWALL

DRYWALL INSTALLATION: Place fixture in mounting location to mark locations of mounting holes. Use a 1/4 in drill bit to drill out the mounting holes for the drywall anchors (B). Pinch the drywall anchor tips together, insert them into the mounting holes, push in until fully inserted and flush with the mounting surface. Drive the long screws (C) into the anchors (B) to securely fasten them into the mounting surface.

FEATURES

**ON/OFF ROCKER SWITCH

**

Press the “ • ” to turn on.

LIGHT SETTING SLIDE SWITCH

Slide switch that allows the color temperature of the light to be adjusted between 3 values:

Grow (3000K): Activates “Plant Grow Mode” which is optimal for growing many plants.

4000K: Cool White
5000K: Bright White

LIGHT ORIENTATION

The Diffuser rotates 115°. Rotate to desired location by using notch on the end cap.

OPTIONAL: INSTALLING ADDITIONAL LIGHTS

  Turn off power before Linking

Use installation steps 1-3 to install additional units. To link, plug the cord into the linking outlet of the preceding fixture.

A maximum of (10)
GL1324-WHT-18LFC-G fixtures can be linked together in one run.

CARE AND MAINTENANCE : Periodically clean the fixture and diffuser using a mild, non abrasive cleaner and soft cloth. When cleaning the fixture, make sure the power is turned off. Do not spray cleaner directly onto any part of the fixture or LEDs.  Good Earth Lighting® – 3 YEAR LIMITED WARRANTY: The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (3) years from the date of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number and an address where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This limitation upon the liability of the manufacturer includes any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state

FCC STATEMENT: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help. FCC responsible party name : Good Earth Lighting, Inc. Address: 1400 E Business Center Drive, STE 108, Mount Prospect IL 60056, USA Telephone number: 1-800-291-8838

TROUBLESHOOTING GUIDE

1. Power/light switch is off.
2. Power cord or Linking cord not properly connected
3. Fixture not properly wired to junction box.
4. Bad switch.

|

1. Verify power supply and light switch are on.
2. Check cords connection.
3. Check wiring connections.
4. Test or replace switch.

2. Fuse blows or circuit breaker trips when light is turned on.| 1. Discontinue use immediately.| 1. Call customer service (1-800-291-8838).

See Packaging for lighting summary and optimal growth recommendations. The information provided on the packaging should only be used as a suggestion. No guarantees of plant health or yield are guaranteed or inferred with the use of these lights. Water, soil, fertilizers, temperature, environment, and other factors will impact plant health.

Good Earth Lighting® 1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
Good Earth Lighting® is a registered trademark of Good Earth Lighting, Inc. © 2021 Good Earth Lighting, Inc.

REPLACEMENT PARTS LIST Hardware Kit: ZH-GL1324

Need Help?

Please visit our website at: https://goodearthlighting.com/contact-us or call the Customer Care Center
1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.

References

• Contact Us | Good Earth Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>