GoodEarth WH1-18LF0-G China Hardware kit Instruction Manual

GoodEarth WH1-18LF0-G China Hardware kit

Product Information

Specifications

• Model Numbers: UC1299-WH1-12LF0-G, UC1299-WH1-18LF0-G, UC1299-WH1-24LF0-G, UC1299-WH1-30LF0-G
• Switch Type: ON/OFF Rocker Switch
• Includes: Hardware kit, Linking cord, Diffuser, Plastic screw cover
• Power Source: AAx2 BBx2 CCx2

Product Usage Instructions

Warnings and Safety Information

• Shut off power at the circuit breaker or fuse panel before removing or installing the fixture.
• Avoid looking directly at exposed LEDs for extended periods.
• Do not use in wet locations, indoor use only.
• Fixture is dimmable with specific forward phase dimmers.
• Avoid mounting over sinks or stoves.
• Turn off power before servicing.
• Do not leave bare wires exposed.
• Maximum number of LED cabinet lighting fixtures per run should not exceed power supply wattage rating (maximum 360 watts).

Installation Instructions

1. Turn off power at the breaker box/fuse box and wall switch to junction box off.
2. Remove the access cover by loosening the locking screw and pulling out the wires.
3. Determine and remove the closest knock-out for the supply wire feed.
4. Option A (NM Cable): Attach plastic strain relief to the knock-out hole and push the NM cable through.
5. Option B (Flexible Whip): Attach metal strain relief to the flexible whip and insert it into the knock-out.
6. Ensure proper grounding by connecting ground supply lead to fixture ground wires, black lead to black wires, and white lead to white wires.
7. Push excess wire into compartment and re-attach the access cover securely.

FAQ:
Q: Can this fixture be used outdoors?
A: No, this fixture is intended for indoor use only and should not be used in wet locations.

LED UNDER CABINET BAR

WARNING: SHUT OFF POWER AT THE CIRCUIT BREAKER OR FUSE PANEL BEFORE REMOVING THE OLD FIXTURE OR INSTALLING A NEW ONE.

WARNINGS AND CAUTIONS

IMPORTANT SAFETY INFORMATION READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!
THIS FIXTURE IS DIMMABLE BY SPECIFIC FORWARD PHASE ELECTRONIC (TRIAC) DIMMERS. Dimmers tested to be compatible with this fixture are the Lutron: Skylark® SCL-153P, Diva® DVCL-153P, Maestro® MACL-153M, Toggler® TGCL-153P, Lumea® LECL-153P, Caseta® PD-6WCL, and Eaton Halo® SAL006P. (This list of dimmers does not imply any guarantee or warranty of compatibility with a particular application. Dimmers not listed do not imply non-compatibility.)

If unsure if the electrical box is properly grounded, or the box is plastic and has no ground wire, or are unfamiliar with the methods of properly grounding fixture, consult a qualified electrician.

1. Do not look directly at exposed LEDs for extended period of time.
2. LEDs gradually emit less light over their lifetime.
3. Do not use in wet locations. FOR INDOOR USE ONLY.
4. Do NOT mount to surfaces less than ¼ in.
5. For electrical requirements, see fixture. Minimum 90°C supply conductors.
6. Do NOT mount over sinks or stoves.
7. Do NOT install these lights inside of enclosed cabinets.
8. Turn power off before servicing.
9. Do not leave bare wires exposed.
10. Not intended for recessed installation in ceiling or soffits.
11. Maximum number of LED cabinet lighting fixtures per run should not exceed power supply wattage rating. Maximum 360 watts.

INSTALLATION

TURN POWER OFF AT BREAKER BOX/FUSE BOX. TURN WALL SWITCH TO JUNCTION BOX OFF

1. Remove the access cover by loosening the locking screw and slide the keyhole slot over the screw head, until it reaches to the large end of the keyhole slot. As the access cover is removed from the fixture, the ends of the wires/wire connectors will be pulled out with it. Carefully, pull the ends out about 3 inches and clip the zip tie that is attaching them to the access door.

2. Determine which corresponding knock-out is closest to the supply wire feed and remove it. CAREFULLY REMOVE THE KNOCK-OUT BY
   HAMMERING A FLAT HEAD SCREWDRIVER OR PUNCH UNTIL THE SURFACE BREAKS. If the knock-out did not break free, use pliers (not included) and bend it back and forth until it snaps off.
   Option A (NM Cable): Attach the round plastic strain relief (CC) by pushing the wedge base into the knock-out hole until it locks into position. Push the NM cable through the strain relief, allowing enough wire length to make the connections.
   Option B (Flexible Whip): Attach the metal strain relief (BB) to the end of the flexible whip and turn until the strain relief (BB) is fully engaged with
   the end of the cable. Push the strain relief (BB) and cable into the knock out and lock into position (allow enough wire length to make the connection).

3. The fixture must be properly grounded. Insert ground supply lead into connector on ground fixture wires.The ground wires can be either green or bare copper. Insert black supply lead into the connector on black fixture wires and white supply lead into the connector on white  wires.

4. Push excess wire into the wire compartment. Re-attach the access cover by sliding the access cover away from the screw head until the screw head is captured by the narrow end of the keyhole slot. Tighten the locking screw back down.

Optional Wiring method: To pass through wiring with power feeding back out to the next fixture the following is provided. For NM cable or Flexible whip, use a second strain relief and the second KO in the access cover. Push the second set of wires into the corresponding quick connect with black to black, white to white and ground to ground.

1. Option 1: Pre-installed Captive Screws: Remove the plastic screw covers from both ends by prying off them with a flathead screwdriver. The fixture has pre-installed captive screws at each end. Hold the fixture in the desired location and drive wood screws until they secure the fixture to the bottom surface of the cabinet. The wood screws must be driven in straight for the fixture to mount properly. DO NOT OVERTIGHTEN to prevent stripping the screw hole. Replace screw covers on both ends.
   ON/OFF ROCKER SWITCH
   

2. Option 2: Keyhole Mount: Locate the mounting keyhole slots on the back of the fixture to measure the distance and mark locations to install the 2 screws (AA). Carefully drive screws in, leaving a little over a 1/16 in. gap. Slide the fixture’s 2 keyhole slots over the 2 screw heads until both sides are captured by the narrow ends of the keyhole slots.

ON/OFF ROCKER SWITCH

CARE AND MAINTENANCE: Periodically clean the fixture and diffuser using a mild, non-abrasive cleaner and soft cloth. When cleaning the fixture, make sure the power is turned off. Do not spray cleaner directly onto any part of the fixture or LEDs.
Good Earth Lighting® – 6 YEAR

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (6) years from the date of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number and an address where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to the replacement of the defective light fixture product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This limitation upon the liability of the manufacturer includes any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.

FCC STATEMENT

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate th equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that of the receiver.
4. Consult the dealer or an experienced radio/TV technician for help.

FCC responsible party name : Good Earth Lighting, Inc. Address: 1400 E Business Center Drive, STE 108, Mount Prospect IL 60056, USA Telephone number: 1-800-291-8838
Before doing any work on the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.

TROUBLESHOOTING GUIDE

1.  Light does not come on.

|

1. Power/ light switch is off.
2. Fixture not properly wired to junction box.
3. Bad switch.

|

1.  Verify power supply and light switch are on.

2. Check wiring connections.

3. Test or replace switch.

4. Fuse blows or circuit breaker trips when light is turned on.

| |

REPLACEMENT PARTS LIST

Hardware Kit:
ZH-UC1299F00-WH1

Replacement Diffuser Model:

• ZD-UC1138LF30-FST,
  ZD-UC1138LF24-FST,

• ZD-UC1138LF18-FST,

• ZD-UC1138LF12-FST

Need Help? Please visit our website at: www.goodearthlighting.com/support or call the Customer Care Center 1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.
Good Earth Lighting® 1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056 Good Earth Lighting® is a registered trademark of Good Earth Lighting, Inc.
© 2020 Good Earth Lighting, Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>