RAB HALV Indoor LED Wall Sconce Instructions

RAB HALV Indoor LED Wall Sconce

INSTRUCTIONS

HALV Indoor Architectural-Grade LED Wall Sconce
RAB Lighting is committed to creating high-quality, affordable, well- designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNINGS:

• Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.

• To prevent wiring damage or abrasion, do not expose wiring to edges of sharp objects.
  CAUTION:

• This fixture supports the following protocols – TRIAC and ELV at 120V ONLY. For 0-10V dimming, connect purple wire to the V+ DIM lead and the grey wire to the V-DIM lead. This fixture is damp listed and suitable for indoor applications on walls. Driver is 120V – 277V and 50Hz or 60 Hz.

JUNCTION BOX WALL MOUNTING

(standard models)
Mounting the fixture on a standard 4 x 4 junction box. This fixture is damp listed and suitable for indoor applications on walls.

1. Loosen the (4) Driver/LED Mounting Phillips head screws and separate the Driver/LED Assembly from the wall plate. No need to remove the screws completely—use the keyhole. DO NOT TOUCH THE LEDs. See Figure 1.
2. Set Driver/LED assembly aside.
3. Pull wires from junction box through the Wall Plate opening and mount Wall Plate to junction box using screws provided with the junction box. Making sure the ‘S’ Hook notch is at the top.
4. Hang the Driver/LED Assembly on the ‘S’ Hook as shown in Figure 1a.
5. Make wiring connections. Push wire nuts through hole into junction box.
6. Replace Driver/LED Assembly making sure not to pinch any wires.
7. Tighten Driver/LED Mounting Screws.

INSTALLATION

NEW CONSTRUCTION INSTALLATION

(models w/wall box)
Wall box is installed before sheetrock.

1. Remove Driver/LED/Wall Plate assembly by loosening 4 Phillips head screws as shown in Figure 1. No need to completely remove screws—keyhole slots provided. Retain Hanger. Unplug connectors (if E2, E2/MVS, E2, E2/BL, or E2/LC) and put Driver/LED/Wall Plate aside.
2. Install Nailer Bars into wall box as shown in Figure 2.
3. Locate the wall box in the desired position between the studs and affix using Nailer Bars.
4. Tighten 1 Phillips head locating screw shown in Figure 2 to hold wall box in position on the Nailer Bars.
5. Run wire to box.

REMODELER INSTALLATION

(models w/wall box)
Wall box is installed after sheetrock.

1. Remove Driver/LED/Wall Plate assembly by loosening 4 Phillips head screws as shown in Figure 1. No need to completely remove screws—keyhole slots provided. Retain Hanger. Unplug connectors (if E2, E2/MVS, E2, E2/BL, or LC/E2) and put Driver/LED/Wall Plate aside.
2. Discard Nailer Bars.
3. Move Stop Brackets from end to side and add Sheetrock Clamps as shown in Figure 3.
4. Using the template provided, cut opening in sheetrock. Leave at least ¾” between box and stud.
5. Run wire to box.
6. Place wall box in opening and tighten 4 Phillips head screws to secure wall box

DRIVER/LED/WALL PLATE/ASSEMBLY (with E2, E2/MVS, E2/BL, or LC/E2 options)

1. Hang Driver/LED/Wall Plate assembly on Hanger as shown in Figure 4.
2. Mate connectors, except for battery connection. Make wiring connections.
3. Energize fixture. Mate battery connection.
4. Remove Hanging Bracket and place in bottom of box for future use.
5. Install Driver/LED/Wall Plate and tighten 4 Phillips head screws.

DRIVER/LED/WALL PLATE/ASSEMBLY (with /LC option)

1. Hang Driver/LED/Wall Plate assembly on Hanger Bracket as shown in Figure 4.
2. Make wire connections.
3. Remove Hanger Bracket and place in bottom of box for future use.
4. Install Driver/LED/Wall Plate and tighten 4 Phillips head screws.

LENS FRAME INSTALLATION

1. Align Lens Frame over the Driver/LED Assembly with the Phillips head Mounting Screw at the top. See Figure 5.
2. Inset the Lens Frame from the bottom with the bottom flush against the wall. See Figure 5.
3. Tilt the top of the Lens Frame to the wall.
4. Make sure the frame is flush against the wall and tighten Mounting Screw at the top using a 5/64” hex key.

WIRING DIAGRAMS

TROUBLESHOOTING

1. Check that the line voltage at the fixture is correct. Refer to wiring directions.
2. Be sure the fixture is grounded properly.

CLEANING AND MAINTENANCE

1. Use warm water, mild soap and a soft sponge or cloth. Any acrylic cleaner may also be used. Do not use alcohol, glass cleaners, acetone, lacquer thinner, solvents or abrasive compounds. Do not use squeegees, scrapers or synthetic rags that may scratch the panels.
   a. Lumicor® lenses – Novus® cleaner and polish is an approved product for a clean shine that also protects from static build up. See the “General Polishing & Basic Scratch Repair” document at www.lumicor.com/ScratchRepair for more information.

2. DO NOT OPEN THE FIXTURE TO CLEAN THE LEDs. DO NOT TOUCH THE LEDs.

DIMENSIONAL DRAWINGS

Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance. RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty.

Visit our website for product info rablighting.com
Tech Help Line Call our experts: 888 722-1000
e-mail Answered promptl y – sales@rablighting.com

References

• Legal - RAB Lighting
• lumicor.com/ScratchRepair

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>