idataLINK 2021 Hyundai Kona Std Key Automatic Owner’s Manual

June 8, 2024
idataLink

idataLINK 2021 Hyundai Kona Std Key Automatic

idataLINK 2021 Hyundai Kona Std Key Automatic

DOCUMENT NUMBER
A51F44A

REVISION DATE
20211218_204130

FIRMWARE
RSA-HK10

HARDWARE
CM-DC3

ACCESSORIES
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED. VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.

TERMS OF USE

Automotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, noncompliant Certified Technicians or end users.

FEATURE LIST

REMOTE START Supported
Data Immobilizer Bypass (no key required)

Key Required for Immobilizer Bypass|

Takeover Available|

No Takeover Available (shutdown on unlock or door open)|

3x Lock Start from OEM Remotes|

Data / MUX Parking Light Control – Constant|

Data / MUX / Hazard Parking Light Control – Flashing|

Tach Monitoring|

Hood Status|

Brake Status|

E-Brake Status|

Glow Plug Status|

RAP Shutdown|

KEYLESS ENTRY Supported
OEM Remotes Functional during RS

OEM RFID Entry Sensors Functional during RS|
Door Lock|

Door Unlock|

Driver Door Priority Unlock|

Trunk/Hatch Release|
Power Liftgate|
Power Sliding Door (L)|
Power Sliding Door (R)|
SECURITY SYSTEM| Supported
---|---
Arm OEM Alarm|

Disarm OEM Alarm|

Aftermarket Alarm Control from OEM Remotes|

Aftermarket Alarm Control from OEM RFID Entry Sensors|
Door Status|

Trunk/Hatch Status|

COMFORT Supported
Rear Defrost Activation
Heated Mirror Activation
Heated Seat Activation
Cooled Seat Activation
Heated Steering Wheel Activation

MODULE LAYOUT

MODULE CONNECTORS

Module Connectors

CONNECTOR PINOUT

Connector Pinout

T-HARNESS / COMPONENT LOCATOR

T-harness / Component Locator

T-HARNESS / WIRING DIAGRAM

T-harness / Wiring Diagram

HARDWIRE / COMPONENT LOCATOR

Hardwire / Component Locator

HARDWIRE / WIRING DIAGRAM

Hardwire / Wiring Diagram

  1. Turn key to ON position

  2. Wait, if LED 1 turns solid GREEN, proceed with step 4. If LED 1 flashes RED three times [3x], proceed with step 3.

  3. The vehicle’s immobilizer is NOT detected: For USDM vehicles without an immobilizer, press and release the module’s programming button. Wait until LED 1 turns solid GREEN then proceed with step 4. For CDM and USDM vehicles with an immobilizer, verify every wire connections and repeat the module programming procedure.

  4. Turn key to OFF position.

  5. START vehicle for 15 seconds.

  6. Press and hold the brake pedal.

  7. Press and release the module’s programming button.

  8. Release the brake pedal.

  9. Wait, LED 2 will flash GREEN.

  10. Module Programming Procedure completed.

All vehicle doors must be closed and locked prior to remote start sequence.

  1. Press unlock on OEM or aftermarket remote.

  2. Insert key into ignition.

  3. Turn key to ON position

  4. Press and release BRAKE pedal.

  5. Take over procedure completed.

Failure to follow procedure will result in vehicle engine shutdown.

REMOTE STARTER ERROR CODES

REMOTE STARTER ERROR CODES: NOTES| PARKING LIGHT FLASHES| DIAGNOSTIC
---|---|---
I  WARNING: The following applies only when the parking lights are connected and supported by the system.

II    After a remote starter failure, the parking lights will flash three [3x] times followed by the error code. See table.

| 3 + 1| Tach is not programmed OR engine is already running.
3 + 2| Key is in ignition ON position.
3 + 3| Door is open.
3 + 4| Trunk is open.
3 + 5| Foot brake is ON.
3 + 6| Hood is open.
3 + 7| Loop is not cut.
3 + 8| No tach detected.
3 + 9| Vehicle movement detected (VSS).
3 + 10| System is in Valet Mode.
3 + 11| CAN communication failure
3 + 12| RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.
3 + 13| Bypass problem.
3 + 14| Idle mode or takeover is not available on this vehicle.
3 + 15| Overheat protection.

REMOTE STARTER SHUTDOWN ERROR CODES: NOTES

|

PARKING LIGHT FLASHES

|

DIAGNOSTIC

---|---|---
I  WARNING: The following applies only when the parking lights are connected and supported by the system.

II If the engine shuts down after a remote starter sequence use the query command from a compatible aftermarket remote to display the shutdown error code. The parking lights will flash four [4x] times followed by the error code. See table.

| 4 + 1| Engine tach signal was lost.
4 + 2| Emergency brake signal was lost.
4 + 3| Foot brake ON detected.
4 + 4| Hood open detected.
4 + 5| Tach over rev detected.
4 + 6| Glow plug timeout error.
4 + 7| Vehicle movement detected (VSS).
4 + 8| Check engine light ON.
4 + 9| Low fuel level.
4 + 10| Open door detected.
4 + 11| CAN communication failure during RS sequence.
4 + 12| RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.
4 + 13| Bypass problem.
4 + 14| Idle mode or takeover is not available on this vehicle.
4 + 15| Overheat protection.

MODULE DIAGNOSTICS

Module Diagnostics

  • LED 2 (RS) displays generic diagnostic codes specific to the remote start module. Orange LED flashes may appear red.
    ** LED 1 (Bypass) displays diagnostic codes specific to the firmware loaded on the module. Visit the programming diagnostics page for more information.

MODULE DIAGNOSTICS

Module Diagnostics

  • LED 2 (RS) displays generic diagnostic codes specific to the remote start module. Orange LED flashes may appear red.
    ** LED 1 (Bypass) displays diagnostic codes specific to the firmware loaded on the module. Visit the programming diagnostics page for more information.

U.S. Patent No. 8,856,780 CA 2759622
Automotive Data Solutions Inc. © 2021
2021 Hyundai Kona STD key Automatic
compustar.idatalink.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

idataLink User Manuals

Related Manuals