idatalink maestro Rr Interface Module Installation Guide
- June 13, 2024
- idataLink
Table of Contents
idatalink maestro Rr Interface Module
Product Information
| Product Name | iDatalink Maestro RR Radio Replacement Interface |
|---|---|
| Compatible Vehicle | 2015-2017 Ford Mustang |
| Features | Retains steering wheel controls, camera, and more |
| Required Products | iDatalink Maestro MUS2 Dash Kit |
| Programmed Firmware | ADS-RR(SR)-FO2C-DS |
| Additional Resources | Maestro RR2 Programmable Outputs Guide |
| Optional Accessories | HEAD UNIT ADAPTER: ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1 |
Product Usage Instructions
- Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.
- Print only the pages for your vehicle using the advanced options in the Print menu.
- Install your Maestro RR according to the guide for your vehicle.
WARNING: Pressing the printer icon or quick printing this document will print all of the guides in this compilation.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
If you need further assistance, you can contact iDatalink Maestro support at 1-866-427-2999 or email them at maestro.support@idatalink.com.
For more information and resources, you can visit the iDatalink Maestro website at maestro.idatalink.com.
Detailed Installation Instructions
Dash Disassembly
- Using a Panel tool carefully pry outward on the larger center console trim panel, then remove the two (2) 7mm screws located behind the panel. Remove the smaller trim panel located directly above the center console. (Fig. 1.1)
- Repeat the previous steps on the driver side.
- Engage the parking brake, turn the key to the ‘ON’ position, and move the shifter into drive.
- Pry the shifter panel upwards to release the clips securing it, then disconnect the wire harness. (Fig. 1.2)
- Remove the two (2) small Phillips screws at the front of the shifter, pull up to remove the shifter, place the vehicle back into park, and turn the ignition switch to ‘OFF’. (Fig. 1.3)
- Using a panel tool, pry upward on the back of the center console to release the clips securing it. Firmly pull back on the center console to release the forward-facing clips securing it in place. (Fig. 1.4)
- Remove the tray below the radio to expose the two (2) 7mm screws and remove them. (Fig. 1.5)
- Open the glove box and pry outward on the passenger side trim panel to the right of the glove box. (Fig. 1.6)
- Remove the upper dash trim panel by prying outward with a panel tool. (Fig. 1.7)
SELECT VEHICLE
PRINT PAGES NEEDED
HOW TO USE THIS INSTALL GUIDE
- Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.
- Print only the pages for your vehicle using the advanced options in the Print menu.
- Install your Maestro RR according to the guide for your vehicle.
WARNING
Pressing the printer icon or “quick printing” this document will print all of
the guides in this compilation.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
INSTALL GUIDE
2015-2017 FORd Mustang
InstallIng 7 Inch scReen
RETAINS STEERING WHEEL CONTROLS, CAMERA AND MORE!
OR
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro MUS2 Dash
Kit
PROGRAMMED FIRMWARE
ADS-RR(SR)-FO2C-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
OPTIONAL ACCESSORIES
ELECTRONICS
Click here for: Radar Installation Guides
HEAD UNIT ADAPTER: ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement
solution. You are now a few simple steps away from enjoying your new car radio
with enhanced features.
Before starting your installation, please ensure that your iDatalink Maestro
module is programmed with the correct firmware for your vehicle and that you
carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were
originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table
FORd Mustang InstallIng 7 Inch scReen 2015-2017
3 7 8 9 10
NEED HELP?
1 866 427-2999
maestro.support@idatalink.com
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
2 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P1/4
DASH DISASSEMBLY
1. Using a Panel tool carefully pry outward on the larger center console trim
panel, then remove the two (2) 7mm screws located behind panel. Remove smaller
trim panel located directly above the center console. (Fig. 1.1)
Repeat previous steps on driver side.
2. Engage parking brake, turn key to ON’ position and move shifter into drive. 3\. Pry shifter panel upwards to release the clips securing it, then disconnect wire harness. (Fig. 1.2) 4\. Remove the two (2) small Phillips screws at front of shifter, pull up to remove shifter and place vehicle back into park and turn ignition switch to OFF’. (Fig. 1.3)
5. Using a panel tool , pry upward on the back of the center console to
release the clips securing it. Firmly pull back on center console to release
the forward-facing clips securing it in place. (Fig. 1.4)
6. Remove tray below radio to expose the two (2) 7mm screws and remove. (Fig.
1.5)
7. Open Glove box and pry outward on passenger side trim panel to the right
of the glovebox. (Fig. 1.6)
8. Remove the upper dash trim panel by pry out outward with panel tool. (Fig.
1.7)
9. Remove small trim plate at base of radio bezel and remove the two (2) 7mm
screws behind it. (Fig. 1.8)
10. Remove the the two (2) 7mm screws at top of radio bezel. Pull outward on
radio bezel to release the clips securing it to the dash, disconnect harnesses
and remove. (Fig. 1.9)
FORd Mustang InstallIng 7 Inch scReen 2015-2017
Fig. 1.1
Fig. 1.2
Fig. 1.3
Fig. 1.4
Fig. 1.5
Fig. 1.6
Fig. 1.7
Automotive Data Solutions Inc. © 2023
1 ADS-RR(SR)-MUS2H-DS-IG-EN
Fig. 1.8
Fig. 1.9
3 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P2/4
REMOVE / DISASSEMBLE THE FACTORY RADIO
11. Remove the four (4) 7mm screws securing cd player mechanism, then
disconnect harnesses and remove. Remove the four (4) 7mm screws securing radio
display, disconnect harnesses and remove. (Fig. 1.10)
12. Remove the four (4) 7mm screws securing the SYNC module to the sub dash
disconnect harnesses and remove. (Fig. 1.11)
13. Remove the fifteen (15) T10 Torx screws from the back of the factory
bezel. Remove the back panel. (Fig. 1.12)
14. Remove the seven (7) T10 Torx screws securing the circuit board. Then,
carefully remove the board from the bezel. (Fig. 1.13)
15. Remove the lower climate and start button assembly. (Fig. 1.14)
16. Using a razor blade, carefully cut the membrane for the radio controls as
shown. Then, remove the lower radio controls. (Fig. 1.15)
17. Using a small flat head screwdriver, release the 2 clips securing the 12V
power port into the bezel. (Fig. 1.16)
FORd Mustang InstallIng 7 Inch scReen 2015-2017
Fig. 1.10
Fig. 1.11
Fig. 1.12
Fig. 1.13
Fig. 1.14
Fig. 1.15
Fig. 1.16
Automotive Data Solutions Inc. © 2023
1 ADS-RR(SR)-MUS2H-DS-IG-EN
4 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P2/4
REMOVE / DISASSEMBLE THE FACTORY RADIO
11. Remove the four (4) 7mm screws securing cd player mechanism, then
disconnect harnesses and remove. Remove the four (4) 7mm screws securing radio
display, disconnect harnesses and remove. (Fig. 1.10)
12. Remove the four (4) 7mm screws securing the SYNC module to the sub dash
disconnect harnesses and remove. (Fig. 1.11)
13. Remove the fifteen (15) T10 Torx screws from the back of the factory
bezel. Remove the back panel. (Fig. 1.12)
14. Remove the seven (7) T10 Torx screws securing the circuit board. Then,
carefully remove the board from the bezel. (Fig. 1.13)
15. Remove the lower climate and start button assembly. (Fig. 1.14)
16. Using a razor blade, carefully cut the membrane for the radio controls as
shown. Then, remove the lower radio controls. (Fig. 1.15)
17. Using a small flat head screwdriver, release the 2 clips securing the 12V
power port into the bezel. (Fig. 1.16)
FORd Mustang InstallIng 7 Inch scReen 2015-2017
Fig. 1.10
Fig. 1.11
Fig. 1.12
Fig. 1.13
Fig. 1.14
Fig. 1.15
Fig. 1.16
Automotive Data Solutions Inc. © 2023
1 ADS-RR(SR)-MUS2H-DS-IG-EN
5 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P2/4
REMOVE / DISASSEMBLE THE FACTORY RADIO
11. Remove the four (4) 7mm screws securing cd player mechanism, then
disconnect harnesses and remove. Remove the four (4) 7mm screws securing radio
display, disconnect harnesses and remove. (Fig. 1.10)
12. Remove the four (4) 7mm screws securing the SYNC module to the sub dash
disconnect harnesses and remove. (Fig. 1.11)
13. Remove the fifteen (15) T10 Torx screws from the back of the factory
bezel. Remove the back panel. (Fig. 1.12)
14. Remove the seven (7) T10 Torx screws securing the circuit board. Then,
carefully remove the board from the bezel. (Fig. 1.13)
15. Remove the lower climate and start button assembly. (Fig. 1.14)
16. Using a razor blade, carefully cut the membrane for the radio controls as
shown. Then, remove the lower radio controls. (Fig. 1.15)
17. Using a small flat head screwdriver, release the 2 clips securing the 12V
power port into the bezel. (Fig. 1.16)
FORd Mustang InstallIng 7 Inch scReen 2015-2017
Fig. 1.10
Fig. 1.11
Fig. 1.12
Fig. 1.13
Fig. 1.14
Fig. 1.15
Fig. 1.16
Automotive Data Solutions Inc. © 2023
1 ADS-RR(SR)-MUS2H-DS-IG-EN
6 maestro.idatalink.com
FORd Mustang InstallIng 7 Inch scReen 2015-2017
WIRING DIAGRAM
STEP 1
WHITE – LF SPEAKER (+) WHITE/BLACK – LF SPEAKER (-) GRAY – RF SPEAKER (+) GRAY/BLACK – RF SPEAKER (-) GREEN – LR SPEAKER (+) GREEN/BLACK – LR SPEAKER (-) PURPLE – RR SPEAKER (+) PURPLE/BLACK – RR SPEAKER (-) BLUE/WHITE – AMP. TURN ON (+) BLACK – GROUND RED – ACCESSORY (+) YELLOW – 12V (+) ORANGE – PARKING LIGHT (+) PURPLE/WHITE – REVERSE LIGHT (+) * LTGREEN – E-BRAKE (-) PINK – VEHICLE SPEED BLUE – POWER ANTENNA
SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS
- ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR
20
IF NOT USING A MAESTRO HEAD UNIT ADAPTER: CUT AND DISCARD CONNECTOR
HEAD UNIT ADAPTER SOLD SEPARATELY
STEP 2
FACTORY RADIO HARNESS
USB ANTENNA ADAPTER
24
STEP 5
PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
MAIN HARNESS
CONNECT TO AFTERMARKET RADIO
OR
IF WIRES ARE PRESENT ON ADAPTER: SEE RADIO REFERENCE CHART
BACKUP CAM
ANTENNA ADAPTER USB ADAPTER
WIRES FROM VEHICLE
DATA AUDIO CABLE CABLE
MUS2 BEZEL
STEP 3
N.C. 3 N.C. 3
N.C. 2
BLACK
MIC 1 MIC 2
STEP 4
YELLOW 2
SYNC HARNESS 54
OEM SCREEN HARNESS A 12
STEP 6
18
MAESTRO RR MODULE 4
4
AMP TURNON
N.C.
MUS2 T-HARNESS
NOT REQUIRED
18
10 3
4
STEERING WHEEL
CONTROL CABLE
1
3
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
7 maestro.idatalink.com
RADIO WIRE REFERENCE CHART
FORd Mustang InstallIng 7 Inch scReen 2015-2017
MUS2 T-harness
Wire Description
Polarity
Wire Color on Maestro T-Harness
Wire Color on Alpine Wire Color on Kenwood/ Wire Color on Pioneer
cable
JVC cable
cable
Wire Color on Sony cable
Illumination
(+)
Reverse Light*
(+)
E-Brake
(-)
VSS (vehicle speed sensor) (DATA)
Power Antenna
(+)
Orange Purple/White
Lt Green Pink Blue
N/A Orange/White Yellow/Blue Green/White
Blue
Orange/White Purple/White
Lt Green Pink Blue
Orange/White Purple/White
Lt Green Pink
Blue/White
Orange Purple/White
Lt Green N/A
Blue or Blue/White
Head unit adapter wiring (optional accessory, sold separately)
ACC-HU-ALP1
Wire Description
Polarity Wire Color on Adapter
VSS (vehicle speed sensor) (DATA)
Green/White
Alpine Radio Green/White
ACC-HU-KEN1
Wire Description
Polarity Wire Color on Adapter
Kenwood Radio
CAM
(+)
CAM
(-)
Steering Wheel Controls
(DATA)
Green/Red Green/White Blue/Yellow
Refer to camera/radio manual
Refer to camera/radio manual
n/a
ACC-HU-KEN2
Wire Description
Polarity Wire Color on Adapter
Kenwood Radio
E-Brake
(-)
LtGreen
LtGreen
Reverse Light*
(+)
Purple/White
Purple/White
Steering Wheel Controls
(DATA)
Blue/Yellow
n/a
- Reverse light wire: Only connect to radio or module damage will occur.
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
8 maestro.idatalink.com
MODULE DIAGNOSTICS
LED 1
PROGRAMMING BUTTON
LED 2
FORd Mustang InstallIng 7 Inch scReen 2015-2017
LED 1
LED 1 Module/Firmware status
· or · · · ·
·
LED 2 (RR2) Bluetooth activity
· ·
LED STATUS
RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes
OFF
DIAGNOSTIC
LED flashes 1 or more times, either red or green, when a steering wheel button
is pressed : normal operation. Module has no firmware. Flash module using
Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult
troubleshooting table.
After radio boots up : Normal operation.
Bluetooth is activated. Turns off after one minute: Normal operation. Normal
operation (inactive).
VIDEO HELP
Installation, product information, vehicle specific videos.
VERIFY FLASH
Last flash information, steering control configuration, vehicle information.
WEBLINK
Software to program module.
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
9 maestro.idatalink.com
FORd Mustang InstallIng 7 Inch scReen 2015-2017
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
The light on the Maestro is blinking RED TWICE and the radio IS turning on.
Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Make sure the correct radio model and serial number were entered during the flash. Verify the radio’s serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.
The light on the Maestro is blinking RED TWICE but radio is NOT turning on.
If installing a modular radio and it is not turning on, ensure the screen is secured and any trim pieces on the radio have been installed fully. Not installing these fully will prevent radio from powering up and show a 2x red error as well. Test red and yellow wires for DC voltage at radio using a multimeter. Contact support if no voltage on red or yellow.
Center HVAC buttons sticking.
Ensure screws on back plate are not over tightened.
No backup camera image.
Verify position of yellow 2pin plug. 2015-2017- 12 pin Screen connector. 20182021- 54 pin SYNC connector.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the
module. Press and hold the module’s programming button and connect all the
connectors back to the module. Wait, the module’s LED will flash RED rapidly
(this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE Phone:
1-866-427-2999 Email:
maestro.support@idatalink.com
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
10 maestro.idatalink.com
INSTALL GUIDE
2018-2023 FORd Mustang
InstallIng 7 Inch scReen
RETAINS STEERING WHEEL CONTROLS, CAMERA AND MORE!
OR
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro MUS2 Dash
Kit
PROGRAMMED FIRMWARE
ADS-RR(SR)-FO2C-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
OPTIONAL ACCESSORIES
ELECTRONICS
Click here for: Radar Installation Guides
HEAD UNIT ADAPTER: ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement
solution. You are now a few simple steps away from enjoying your new car radio
with enhanced features.
Before starting your installation, please ensure that your iDatalink Maestro
module is programmed with the correct firmware for your vehicle and that you
carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were
originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions Wiring Diagram Radio Wire Reference Chart Module
Diagnostics Troubleshooting Table
FORd Mustang InstallIng 7 Inch scReen 2018-2023
3 7 8 9 10
NEED HELP?
1 866 427-2999
maestro.support@idatalink.com
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
2 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P1/4
DASH DISASSEMBLY
1. Using a Panel tool carefully pry outward on the larger center console trim
panel, then remove the two (2) 7mm screws located behind panel. Remove smaller
trim panel located directly above the center console. (Fig. 1.1)
Repeat previous steps on driver side.
2. Engage parking brake, turn key to ON’ position and move shifter into drive. 3\. Pry shifter panel upwards to release the clips securing it, then disconnect wire harness. (Fig. 1.2) 4\. Remove the two (2) small Phillips screws at front of shifter, pull up to remove shifter and place vehicle back into park and turn ignition switch to OFF’. (Fig. 1.3)
5. Using a panel tool , pry upward on the back of the center console to
release the clips securing it. Firmly pull back on center console to release
the forward-facing clips securing it in place. (Fig. 1.4)
6. Remove tray below radio to expose the two (2) 7mm screws and remove. (Fig.
1.5)
7. Open Glove box and pry outward on passenger side trim panel to the right
of the glovebox. (Fig. 1.6)
8. Remove the upper dash trim panel by pry out outward with panel tool. (Fig.
1.7)
9. Remove small trim plate at base of radio bezel and remove the two (2) 7mm
screws behind it. (Fig. 1.8)
10. Remove the the two (2) 7mm screws at top of radio bezel. Pull outward on
radio bezel to release the clips securing it to the dash, disconnect harnesses
and remove. (Fig. 1.9)
FORd Mustang InstallIng 7 Inch scReen 2018-2023
Fig. 1.1
Fig. 1.2
Fig. 1.3
Fig. 1.4
Fig. 1.5
Fig. 1.6
Fig. 1.7
Automotive Data Solutions Inc. © 2023
2 ADS-RR(SR)-MUS2H-DS-IG-EN
Fig. 1.8
Fig. 1.9
3 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P2/4
REMOVE / DISASSEMBLE THE FACTORY RADIO
11. Remove the four (4) 7mm screws securing cd player mechanism, then
disconnect harnesses and remove. Remove the four (4) 7mm screws securing radio
display and SYNC module, disconnect harnesses and remove. (Fig. 1.10)
12. Remove the fifteen (15) T10 Torx screws from the back of the factory
bezel. Remove the back panel. (Fig. 1.12)
13. Remove the seven (7) T10 Torx screws securing the circuit board. Then,
carefully remove the board from the bezel. (Fig. 1.13)
14. Remove the lower climate and start button assembly. (Fig. 1.14)
15. Using a razor blade, carefully cut the membrane for the radio controls as
shown. Then, remove the lower radio controls. (Fig. 1.15)
16. Using a small flat head screwdriver, release the 2 clips securing the 12V
power port into the bezel. (Fig. 1.16)
FORd Mustang InstallIng 7 Inch scReen 2018-2023
Fig. 1.10
Fig. 1.12
Fig. 1.13
Fig. 1.14
Fig. 1.15
Fig. 1.16
Automotive Data Solutions Inc. © 2023
2 ADS-RR(SR)-MUS2H-DS-IG-EN
4 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P2/4
REMOVE / DISASSEMBLE THE FACTORY RADIO
11. Remove the four (4) 7mm screws securing cd player mechanism, then
disconnect harnesses and remove. Remove the four (4) 7mm screws securing radio
display and SYNC module, disconnect harnesses and remove. (Fig. 1.10)
12. Remove the fifteen (15) T10 Torx screws from the back of the factory
bezel. Remove the back panel. (Fig. 1.12)
13. Remove the seven (7) T10 Torx screws securing the circuit board. Then,
carefully remove the board from the bezel. (Fig. 1.13)
14. Remove the lower climate and start button assembly. (Fig. 1.14)
15. Using a razor blade, carefully cut the membrane for the radio controls as
shown. Then, remove the lower radio controls. (Fig. 1.15)
16. Using a small flat head screwdriver, release the 2 clips securing the 12V
power port into the bezel. (Fig. 1.16)
FORd Mustang InstallIng 7 Inch scReen 2018-2023
Fig. 1.10
Fig. 1.12
Fig. 1.13
Fig. 1.14
Fig. 1.15
Fig. 1.16
Automotive Data Solutions Inc. © 2023
2 ADS-RR(SR)-MUS2H-DS-IG-EN
5 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P2/4
REMOVE / DISASSEMBLE THE FACTORY RADIO
11. Remove the four (4) 7mm screws securing cd player mechanism, then
disconnect harnesses and remove. Remove the four (4) 7mm screws securing radio
display and SYNC module, disconnect harnesses and remove. (Fig. 1.10)
12. Remove the fifteen (15) T10 Torx screws from the back of the factory
bezel. Remove the back panel. (Fig. 1.12)
13. Remove the seven (7) T10 Torx screws securing the circuit board. Then,
carefully remove the board from the bezel. (Fig. 1.13)
14. Remove the lower climate and start button assembly. (Fig. 1.14)
15. Using a razor blade, carefully cut the membrane for the radio controls as
shown. Then, remove the lower radio controls. (Fig. 1.15)
16. Using a small flat head screwdriver, release the 2 clips securing the 12V
power port into the bezel. (Fig. 1.16)
FORd Mustang InstallIng 7 Inch scReen 2018-2023
Fig. 1.10
Fig. 1.12
Fig. 1.13
Fig. 1.14
Fig. 1.15
Fig. 1.16
Automotive Data Solutions Inc. © 2023
2 ADS-RR(SR)-MUS2H-DS-IG-EN
6 maestro.idatalink.com
FORd Mustang InstallIng 7 Inch scReen 2018-2023
WIRING DIAGRAM
STEP 1
WHITE – LF SPEAKER (+) WHITE/BLACK – LF SPEAKER (-) GRAY – RF SPEAKER (+) GRAY/BLACK – RF SPEAKER (-) GREEN – LR SPEAKER (+) GREEN/BLACK – LR SPEAKER (-) PURPLE – RR SPEAKER (+) PURPLE/BLACK – RR SPEAKER (-) BLUE/WHITE – AMP. TURN ON (+) BLACK – GROUND RED – ACCESSORY (+) YELLOW – 12V (+) ORANGE – PARKING LIGHT (+) PURPLE/WHITE – REVERSE LIGHT (+) * LTGREEN – E-BRAKE (-) PINK – VEHICLE SPEED BLUE – POWER ANTENNA
SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS
- ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR
20
IF NOT USING A MAESTRO HEAD UNIT ADAPTER: CUT AND DISCARD CONNECTOR
HEAD UNIT ADAPTER SOLD SEPARATELY
STEP 2
FACTORY RADIO HARNESS
USB ANTENNA ADAPTER
24
STEP 4
PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
MAIN HARNESS
CONNECT TO AFTERMARKET RADIO
OR
IF WIRES ARE PRESENT ON ADAPTER: SEE RADIO REFERENCE CHART
BACKUP CAM
ANTENNA ADAPTER USB ADAPTER
WIRES FROM VEHICLE
DATA AUDIO CABLE CABLE
MUS2 BEZEL
STEP 3
N.C. 3 YELLOW N.C. 3
2
2 BLACK
MIC 1 MIC 2
SYNC HARNESS 54
STEP 5
18
MAESTRO RR MODULE 4
4
AMP TURNON
N.C.
MUS2 T-HARNESS
NOT REQUIRED
18
A 12
10 3
4
STEERING WHEEL
CONTROL CABLE
2
3
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
7 maestro.idatalink.com
RADIO WIRE REFERENCE CHART
FORd Mustang InstallIng 7 Inch scReen 2018-2023
MUS2 T-harness
Wire Description
Polarity
Wire Color on Maestro T-Harness
Wire Color on Alpine Wire Color on Kenwood/ Wire Color on Pioneer
cable
JVC cable
cable
Wire Color on Sony cable
Illumination
(+)
Reverse Light*
(+)
E-Brake
(-)
VSS (vehicle speed sensor) (DATA)
Power Antenna
(+)
Orange Purple/White
Lt Green Pink Blue
N/A Orange/White Yellow/Blue Green/White
Blue
Orange/White Purple/White
Lt Green Pink Blue
Orange/White Purple/White
Lt Green Pink
Blue/White
Orange Purple/White
Lt Green N/A
Blue or Blue/White
Head unit adapter wiring (optional accessory, sold separately)
ACC-HU-ALP1
Wire Description
Polarity Wire Color on Adapter
VSS (vehicle speed sensor) (DATA)
Green/White
Alpine Radio Green/White
ACC-HU-KEN1
Wire Description
Polarity Wire Color on Adapter
Kenwood Radio
CAM
(+)
CAM
(-)
Steering Wheel Controls
(DATA)
Green/Red Green/White Blue/Yellow
Refer to camera/radio manual
Refer to camera/radio manual
n/a
ACC-HU-KEN2
Wire Description
Polarity Wire Color on Adapter
Kenwood Radio
E-Brake
(-)
LtGreen
LtGreen
Reverse Light*
(+)
Purple/White
Purple/White
Steering Wheel Controls
(DATA)
Blue/Yellow
n/a
- Reverse light wire: Only connect to radio or module damage will occur.
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
8 maestro.idatalink.com
MODULE DIAGNOSTICS
LED 1
PROGRAMMING BUTTON
LED 2
FORd Mustang InstallIng 7 Inch scReen 2018-2023
LED 1
LED 1 Module/Firmware status
· or · · · ·
·
LED 2 (RR2) Bluetooth activity
· ·
LED STATUS
RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes
OFF
DIAGNOSTIC
LED flashes 1 or more times, either red or green, when a steering wheel button
is pressed : normal operation. Module has no firmware. Flash module using
Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult
troubleshooting table.
After radio boots up : Normal operation.
Bluetooth is activated. Turns off after one minute: Normal operation. Normal
operation (inactive).
VIDEO HELP
Installation, product information, vehicle specific videos.
VERIFY FLASH
Last flash information, steering control configuration, vehicle information.
WEBLINK
Software to program module.
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
9 maestro.idatalink.com
FORd Mustang InstallIng 7 Inch scReen 2018-2023
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
The light on the Maestro is blinking RED TWICE and the radio IS turning on.
Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Make sure the correct radio model and serial number were entered during the flash. Verify the radio’s serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.
The light on the Maestro is blinking RED TWICE but radio is NOT turning on.
If installing a modular radio and it is not turning on, ensure the screen is secured and any trim pieces on the radio have been installed fully. Not installing these fully will prevent radio from powering up and show a 2x red error as well. Test red and yellow wires for DC voltage at radio using a multimeter. Contact support if no voltage on red or yellow.
Center HVAC buttons sticking.
Ensure screws on back plate are not over tightened.
No backup camera image.
Verify position of yellow 2pin plug. 2015-2017- 12 pin Screen connector. 20182021- 54 pin SYNC connector.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the
module. Press and hold the module’s programming button and connect all the
connectors back to the module. Wait, the module’s LED will flash RED rapidly
(this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE Phone:
1-866-427-2999 Email:
maestro.support@idatalink.com
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
10 maestro.idatalink.com
INSTALL GUIDE
2015-2017 FORd Mustang
InstallIng 8 OR 9 Inch scReen
RETAINS STEERING WHEEL CONTROLS, CAMERA AND MORE!
OR
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro MUS2 Dash
Kit
PROGRAMMED FIRMWARE
ADS-RR(SR)-FO2C-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
OPTIONAL ACCESSORIES
ELECTRONICS
Click here for: Radar Installation Guides
HEAD UNIT ADAPTER: ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement
solution. You are now a few simple steps away from enjoying your new car radio
with enhanced features.
Before starting your installation, please ensure that your iDatalink Maestro
module is programmed with the correct firmware for your vehicle and that you
carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were
originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions Wiring Diagram Radio Wire Reference Chart Module
Diagnostics Troubleshooting Table
FORd Mustang InstallIng 8 OR 9 Inch scReen 2015-2017
3 7 8 9 10
NEED HELP?
1 866 427-2999
maestro.support@idatalink.com
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
2 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P1/4
DASH DISASSEMBLY
1. Using a Panel tool carefully pry outward on the larger center console trim
panel, then remove the two (2) 7mm screws located behind panel. Remove smaller
trim panel located directly above the center console. (Fig. 1.1)
Repeat previous steps on driver side.
2. Engage parking brake, turn key to ON’ position and move shifter into drive. 3\. Pry shifter panel upwards to release the clips securing it, then disconnect wire harness. (Fig. 1.2) 4\. Remove the two (2) small Phillips screws at front of shifter, pull up to remove shifter and place vehicle back into park and turn ignition switch to OFF’. (Fig. 1.3)
5. Using a panel tool , pry upward on the back of the center console to
release the clips securing it. Firmly pull back on center console to release
the forward-facing clips securing it in place. (Fig. 1.4)
6. Remove tray below radio to expose the two (2) 7mm screws and remove. (Fig.
1.5)
7. Open Glove box and pry outward on passenger side trim panel to the right
of the glovebox. (Fig. 1.6)
8. Remove the upper dash trim panel by pry out outward with panel tool. (Fig.
1.7)
9. Remove small trim plate at base of radio bezel and remove the two (2) 7mm
screws behind it. (Fig. 1.8)
10. Remove the the two (2) 7mm screws at top of radio bezel. Pull outward on
radio bezel to release the clips securing it to the dash, disconnect harnesses
and remove. (Fig. 1.9)
FORd Mustang InstallIng 8 OR 9 Inch scReen 2015-2017
Fig. 1.1
Fig. 1.2
Fig. 1.3
Fig. 1.4
Fig. 1.5
Fig. 1.6
Fig. 1.7
Automotive Data Solutions Inc. © 2023
3 ADS-RR(SR)-MUS2H-DS-IG-EN
Fig. 1.8
Fig. 1.9
3 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P2/4
REMOVE / DISASSEMBLE THE FACTORY RADIO
11. Remove the four (4) 7mm screws securing cd player mechanism, then
disconnect harnesses and remove. Remove the four (4) 7mm screws securing radio
display, disconnect harnesses and remove. (Fig. 1.10)
12. Remove the four (4) 7mm screws securing the SYNC module to the sub dash
disconnect harnesses and remove. (Fig. 1.11)
13. Remove the fifteen (15) T10 Torx screws from the back of the factory
bezel. Remove the back panel. (Fig. 1.12)
14. Remove the seven (7) T10 Torx screws securing the circuit board. Then,
carefully remove the board from the bezel. (Fig. 1.13)
15. Remove the lower climate and start button assembly. (Fig. 1.14)
16. Using a razor blade, carefully cut the membrane for the radio controls as
shown. Then, remove the lower radio controls. (Fig. 1.15)
17. Using a small flat head screwdriver, release the 2 clips securing the 12V
power port into the bezel. (Fig. 1.16)
INSTALL THE RADIO BRACKETS
18. Remove the six (6) Phillips screws securing the mounting brackets to the
factory cd player. (Fig. 1.15)
19. Cut off, or bend the alignment tabs on both left and right brackets.
(Fig. 1.16)
20. Install factory brackets to aftermarket radio brain aligning the center
hole of the backets with the mounting locations on the radio brain, secure
with ISO screws provided with aftermarket radio. (Fig. 1.17)
FORd Mustang InstallIng 8 OR 9 Inch scReen 2015-2017
Fig. 1.10
Fig. 1.11
Fig. 1.12
Fig. 1.13
Fig. 1.14
Fig. 1.15
Fig. 1.16
Fig. 1.17
Automotive Data Solutions Inc. © 2023
3 ADS-RR(SR)-MUS2H-DS-IG-EN
4 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P2/4
REMOVE / DISASSEMBLE THE FACTORY RADIO
11. Remove the four (4) 7mm screws securing cd player mechanism, then
disconnect harnesses and remove. Remove the four (4) 7mm screws securing radio
display, disconnect harnesses and remove. (Fig. 1.10)
12. Remove the four (4) 7mm screws securing the SYNC module to the sub dash
disconnect harnesses and remove. (Fig. 1.11)
13. Remove the fifteen (15) T10 Torx screws from the back of the factory
bezel. Remove the back panel. (Fig. 1.12)
14. Remove the seven (7) T10 Torx screws securing the circuit board. Then,
carefully remove the board from the bezel. (Fig. 1.13)
15. Remove the lower climate and start button assembly. (Fig. 1.14)
16. Using a razor blade, carefully cut the membrane for the radio controls as
shown. Then, remove the lower radio controls. (Fig. 1.15)
17. Using a small flat head screwdriver, release the 2 clips securing the 12V
power port into the bezel. (Fig. 1.16)
INSTALL THE RADIO BRACKETS
18. Remove the six (6) Phillips screws securing the mounting brackets to the
factory cd player. (Fig. 1.15)
19. Cut off, or bend the alignment tabs on both left and right brackets.
(Fig. 1.16)
20. Install factory brackets to aftermarket radio brain aligning the center
hole of the backets with the mounting locations on the radio brain, secure
with ISO screws provided with aftermarket radio. (Fig. 1.17)
FORd Mustang InstallIng 8 OR 9 Inch scReen 2015-2017
Fig. 1.10
Fig. 1.11
Fig. 1.12
Fig. 1.13
Fig. 1.14
Fig. 1.15
Fig. 1.16
Fig. 1.17
Automotive Data Solutions Inc. © 2023
3 ADS-RR(SR)-MUS2H-DS-IG-EN
5 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P2/4
REMOVE / DISASSEMBLE THE FACTORY RADIO
11. Remove the four (4) 7mm screws securing cd player mechanism, then
disconnect harnesses and remove. Remove the four (4) 7mm screws securing radio
display, disconnect harnesses and remove. (Fig. 1.10)
12. Remove the four (4) 7mm screws securing the SYNC module to the sub dash
disconnect harnesses and remove. (Fig. 1.11)
13. Remove the fifteen (15) T10 Torx screws from the back of the factory
bezel. Remove the back panel. (Fig. 1.12)
14. Remove the seven (7) T10 Torx screws securing the circuit board. Then,
carefully remove the board from the bezel. (Fig. 1.13)
15. Remove the lower climate and start button assembly. (Fig. 1.14)
16. Using a razor blade, carefully cut the membrane for the radio controls as
shown. Then, remove the lower radio controls. (Fig. 1.15)
17. Using a small flat head screwdriver, release the 2 clips securing the 12V
power port into the bezel. (Fig. 1.16)
INSTALL THE RADIO BRACKETS
18. Remove the six (6) Phillips screws securing the mounting brackets to the
factory cd player. (Fig. 1.15)
19. Cut off, or bend the alignment tabs on both left and right brackets.
(Fig. 1.16)
20. Install factory brackets to aftermarket radio brain aligning the center
hole of the backets with the mounting locations on the radio brain, secure
with ISO screws provided with aftermarket radio. (Fig. 1.17)
FORd Mustang InstallIng 8 OR 9 Inch scReen 2015-2017
Fig. 1.10
Fig. 1.11
Fig. 1.12
Fig. 1.13
Fig. 1.14
Fig. 1.15
Fig. 1.16
Fig. 1.17
Automotive Data Solutions Inc. © 2023
3 ADS-RR(SR)-MUS2H-DS-IG-EN
6 maestro.idatalink.com
FORd Mustang InstallIng 8 OR 9 Inch scReen 2015-2017
WIRING DIAGRAM
STEP 1
WHITE – LF SPEAKER (+) WHITE/BLACK – LF SPEAKER (-) GRAY – RF SPEAKER (+) GRAY/BLACK – RF SPEAKER (-) GREEN – LR SPEAKER (+) GREEN/BLACK – LR SPEAKER (-) PURPLE – RR SPEAKER (+) PURPLE/BLACK – RR SPEAKER (-) BLUE/WHITE – AMP. TURN ON (+) BLACK – GROUND RED – ACCESSORY (+) YELLOW – 12V (+) ORANGE – PARKING LIGHT (+) PURPLE/WHITE – REVERSE LIGHT (+) * LTGREEN – E-BRAKE (-) PINK – VEHICLE SPEED BLUE – POWER ANTENNA
SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS
- ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR
20
IF NOT USING A MAESTRO HEAD UNIT ADAPTER: CUT AND DISCARD CONNECTOR
HEAD UNIT ADAPTER SOLD SEPARATELY
STEP 2
FACTORY RADIO HARNESS
USB ANTENNA ADAPTER
24
STEP 5
PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
MAIN HARNESS
CONNECT TO AFTERMARKET RADIO
OR
IF WIRES ARE PRESENT ON ADAPTER: SEE RADIO REFERENCE CHART
BACKUP CAM
ANTENNA ADAPTER USB ADAPTER
WIRES FROM VEHICLE
DATA AUDIO CABLE CABLE
MUS2 BEZEL
STEP 3
N.C. 3 N.C. 3
N.C. 2
BLACK
MIC 1 MIC 2
STEP 4
YELLOW 2
SYNC HARNESS 54
OEM SCREEN HARNESS A 12
STEP 6
18
MAESTRO RR MODULE 4
4
AMP TURNON
N.C.
MUS2 T-HARNESS
NOT REQUIRED
18
10 3
4
STEERING WHEEL
CONTROL CABLE
3
3
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
7 maestro.idatalink.com
RADIO WIRE REFERENCE CHART
FORd Mustang InstallIng 8 OR 9 Inch scReen 2015-2017
MUS2 T-harness
Wire Description
Polarity
Wire Color on Maestro T-Harness
Wire Color on Alpine Wire Color on Kenwood/ Wire Color on Pioneer
cable
JVC cable
cable
Wire Color on Sony cable
Illumination
(+)
Reverse Light*
(+)
E-Brake
(-)
VSS (vehicle speed sensor) (DATA)
Power Antenna
(+)
Orange Purple/White
Lt Green Pink Blue
N/A Orange/White Yellow/Blue Green/White
Blue
Orange/White Purple/White
Lt Green Pink Blue
Orange/White Purple/White
Lt Green Pink
Blue/White
Orange Purple/White
Lt Green N/A
Blue or Blue/White
Head unit adapter wiring (optional accessory, sold separately)
ACC-HU-ALP1
Wire Description
Polarity Wire Color on Adapter
VSS (vehicle speed sensor) (DATA)
Green/White
Alpine Radio Green/White
ACC-HU-KEN1
Wire Description
Polarity Wire Color on Adapter
Kenwood Radio
CAM
(+)
CAM
(-)
Steering Wheel Controls
(DATA)
Green/Red Green/White Blue/Yellow
Refer to camera/radio manual
Refer to camera/radio manual
n/a
ACC-HU-KEN2
Wire Description
Polarity Wire Color on Adapter
Kenwood Radio
E-Brake
(-)
LtGreen
LtGreen
Reverse Light*
(+)
Purple/White
Purple/White
Steering Wheel Controls
(DATA)
Blue/Yellow
n/a
- Reverse light wire: Only connect to radio or module damage will occur.
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
8 maestro.idatalink.com
MODULE DIAGNOSTICS
LED 1
PROGRAMMING BUTTON
LED 2
FORd Mustang InstallIng 8 OR 9 Inch scReen 2015-2017
LED 1
LED 1 Module/Firmware status
· or · · · ·
·
LED 2 (RR2) Bluetooth activity
· ·
LED STATUS
RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes
OFF
DIAGNOSTIC
LED flashes 1 or more times, either red or green, when a steering wheel button
is pressed : normal operation. Module has no firmware. Flash module using
Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult
troubleshooting table.
After radio boots up : Normal operation.
Bluetooth is activated. Turns off after one minute: Normal operation. Normal
operation (inactive).
VIDEO HELP
Installation, product information, vehicle specific videos.
VERIFY FLASH
Last flash information, steering control configuration, vehicle information.
WEBLINK
Software to program module.
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
9 maestro.idatalink.com
FORd Mustang InstallIng 8 OR 9 Inch scReen 2015-2017
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
The light on the Maestro is blinking RED TWICE and the radio IS turning on.
Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Make sure the correct radio model and serial number were entered during the flash. Verify the radio’s serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.
The light on the Maestro is blinking RED TWICE but radio is NOT turning on.
If installing a modular radio and it is not turning on, ensure the screen is secured and any trim pieces on the radio have been installed fully. Not installing these fully will prevent radio from powering up and show a 2x red error as well. Test red and yellow wires for DC voltage at radio using a multimeter. Contact support if no voltage on red or yellow.
Center HVAC buttons sticking.
Ensure screws on back plate are not over tightened.
No backup camera image.
Verify position of yellow 2pin plug. 2015-2017- 12 pin Screen connector. 20182021- 54 pin SYNC connector.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the
module. Press and hold the module’s programming button and connect all the
connectors back to the module. Wait, the module’s LED will flash RED rapidly
(this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE Phone:
1-866-427-2999 Email:
maestro.support@idatalink.com
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
10 maestro.idatalink.com
INSTALL GUIDE
2018-2023 FORd Mustang
InstallIng 8 OR 9 Inch scReen
RETAINS STEERING WHEEL CONTROLS, CAMERA AND MORE!
OR
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro MUS2 Dash
Kit
PROGRAMMED FIRMWARE
ADS-RR(SR)-FO2C-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
OPTIONAL ACCESSORIES
ELECTRONICS
Click here for: Radar Installation Guides
HEAD UNIT ADAPTER: ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement
solution. You are now a few simple steps away from enjoying your new car radio
with enhanced features.
Before starting your installation, please ensure that your iDatalink Maestro
module is programmed with the correct firmware for your vehicle and that you
carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were
originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions Wiring Diagram Radio Wire Reference Chart Module
Diagnostics Troubleshooting Table
FORd Mustang InstallIng 8 OR 9 Inch scReen 2018-2023
3 7 8 9 10
NEED HELP?
1 866 427-2999
maestro.support@idatalink.com
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
2 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P1/4
DASH DISASSEMBLY
1. Using a Panel tool carefully pry outward on the larger center console trim
panel, then remove the two (2) 7mm screws located behind panel. Remove smaller
trim panel located directly above the center console. (Fig. 1.1)
Repeat previous steps on driver side.
2. Engage parking brake, turn key to ON’ position and move shifter into drive. 3\. Pry shifter panel upwards to release the clips securing it, then disconnect wire harness. (Fig. 1.2) 4\. Remove the two (2) small Phillips screws at front of shifter, pull up to remove shifter and place vehicle back into park and turn ignition switch to OFF’. (Fig. 1.3)
5. Using a panel tool , pry upward on the back of the center console to
release the clips securing it. Firmly pull back on center console to release
the forward-facing clips securing it in place. (Fig. 1.4)
6. Remove tray below radio to expose the two (2) 7mm screws and remove. (Fig.
1.5)
7. Open Glove box and pry outward on passenger side trim panel to the right
of the glovebox. (Fig. 1.6)
8. Remove the upper dash trim panel by pry out outward with panel tool. (Fig.
1.7)
9. Remove small trim plate at base of radio bezel and remove the two (2) 7mm
screws behind it. (Fig. 1.8)
10. Remove the the two (2) 7mm screws at top of radio bezel. Pull outward on
radio bezel to release the clips securing it to the dash, disconnect harnesses
and remove. (Fig. 1.9)
FORd Mustang InstallIng 8 OR 9 Inch scReen 2018-2023
Fig. 1.1
Fig. 1.2
Fig. 1.3
Fig. 1.4
Fig. 1.5
Fig. 1.6
Fig. 1.7
Automotive Data Solutions Inc. © 2023
4 ADS-RR(SR)-MUS2H-DS-IG-EN
Fig. 1.8
Fig. 1.9
3 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P2/4
REMOVE / DISASSEMBLE THE FACTORY RADIO
11. Remove the four (4) 7mm screws securing cd player mechanism, then
disconnect harnesses and remove. Remove the four (4) 7mm screws securing radio
display and SYNC module, disconnect harnesses and remove. (Fig. 1.10)
12. Remove the fifteen (15) T10 Torx screws from the back of the factory
bezel. Remove the back panel. (Fig. 1.11)
13. Remove the seven (7) T10 Torx screws securing the circuit board. Then,
carefully remove the board from the bezel. (Fig. 1.12)
14. Remove the lower climate and start button assembly. (Fig. 1.13)
15. Using a razor blade, carefully cut the membrane for the radio controls as
shown. Then, remove the lower radio controls. (Fig. 1.14)
16. Using a small flat head screwdriver, release the 2 clips securing the 12V
power port into the bezel. (Fig. 1.15)
INSTALL THE RADIO BRACKETS
17. Remove the six (6) Phillips screws securing the mounting brackets to the
factory cd player. (Fig. 1.16)
18. Cut off, or bend the alignment tabs on both left and right brackets.
(Fig. 1.17)
19. Install factory brackets to aftermarket radio brain aligning the center
hole of the backets with the mounting locations on the radio brain, secure
with ISO screws provided with aftermarket radio. (Fig. 1.18)
FORd Mustang InstallIng 8 OR 9 Inch scReen 2018-2023
Fig. 1.10
Fig. 1.11
Fig. 1.12
Fig. 1.13
Fig. 1.14
Fig. 1.15
Fig. 1.16
Fig. 1.17
Automotive Data Solutions Inc. © 2023
4 ADS-RR(SR)-MUS2H-DS-IG-EN
Fig. 1.18
4 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P2/4
REMOVE / DISASSEMBLE THE FACTORY RADIO
11. Remove the four (4) 7mm screws securing cd player mechanism, then
disconnect harnesses and remove. Remove the four (4) 7mm screws securing radio
display and SYNC module, disconnect harnesses and remove. (Fig. 1.10)
12. Remove the fifteen (15) T10 Torx screws from the back of the factory
bezel. Remove the back panel. (Fig. 1.11)
13. Remove the seven (7) T10 Torx screws securing the circuit board. Then,
carefully remove the board from the bezel. (Fig. 1.12)
14. Remove the lower climate and start button assembly. (Fig. 1.13)
15. Using a razor blade, carefully cut the membrane for the radio controls as
shown. Then, remove the lower radio controls. (Fig. 1.14)
16. Using a small flat head screwdriver, release the 2 clips securing the 12V
power port into the bezel. (Fig. 1.15)
INSTALL THE RADIO BRACKETS
17. Remove the six (6) Phillips screws securing the mounting brackets to the
factory cd player. (Fig. 1.16)
18. Cut off, or bend the alignment tabs on both left and right brackets.
(Fig. 1.17)
19. Install factory brackets to aftermarket radio brain aligning the center
hole of the backets with the mounting locations on the radio brain, secure
with ISO screws provided with aftermarket radio. (Fig. 1.18)
FORd Mustang InstallIng 8 OR 9 Inch scReen 2018-2023
Fig. 1.10
Fig. 1.11
Fig. 1.12
Fig. 1.13
Fig. 1.14
Fig. 1.15
Fig. 1.16
Fig. 1.17
Automotive Data Solutions Inc. © 2023
4 ADS-RR(SR)-MUS2H-DS-IG-EN
Fig. 1.18
5 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P2/4
REMOVE / DISASSEMBLE THE FACTORY RADIO
11. Remove the four (4) 7mm screws securing cd player mechanism, then
disconnect harnesses and remove. Remove the four (4) 7mm screws securing radio
display and SYNC module, disconnect harnesses and remove. (Fig. 1.10)
12. Remove the fifteen (15) T10 Torx screws from the back of the factory
bezel. Remove the back panel. (Fig. 1.11)
13. Remove the seven (7) T10 Torx screws securing the circuit board. Then,
carefully remove the board from the bezel. (Fig. 1.12)
14. Remove the lower climate and start button assembly. (Fig. 1.13)
15. Using a razor blade, carefully cut the membrane for the radio controls as
shown. Then, remove the lower radio controls. (Fig. 1.14)
16. Using a small flat head screwdriver, release the 2 clips securing the 12V
power port into the bezel. (Fig. 1.15)
INSTALL THE RADIO BRACKETS
17. Remove the six (6) Phillips screws securing the mounting brackets to the
factory cd player. (Fig. 1.16)
18. Cut off, or bend the alignment tabs on both left and right brackets.
(Fig. 1.17)
19. Install factory brackets to aftermarket radio brain aligning the center
hole of the backets with the mounting locations on the radio brain, secure
with ISO screws provided with aftermarket radio. (Fig. 1.18)
FORd Mustang InstallIng 8 OR 9 Inch scReen 2018-2023
Fig. 1.10
Fig. 1.11
Fig. 1.12
Fig. 1.13
Fig. 1.14
Fig. 1.15
Fig. 1.16
Fig. 1.17
Automotive Data Solutions Inc. © 2023
4 ADS-RR(SR)-MUS2H-DS-IG-EN
Fig. 1.18
6 maestro.idatalink.com
FORd Mustang InstallIng 8 OR 9 Inch scReen 2018-2023
WIRING DIAGRAM
STEP 1
WHITE – LF SPEAKER (+) WHITE/BLACK – LF SPEAKER (-) GRAY – RF SPEAKER (+) GRAY/BLACK – RF SPEAKER (-) GREEN – LR SPEAKER (+) GREEN/BLACK – LR SPEAKER (-) PURPLE – RR SPEAKER (+) PURPLE/BLACK – RR SPEAKER (-) BLUE/WHITE – AMP. TURN ON (+) BLACK – GROUND RED – ACCESSORY (+) YELLOW – 12V (+) ORANGE – PARKING LIGHT (+) PURPLE/WHITE – REVERSE LIGHT (+) * LTGREEN – E-BRAKE (-) PINK – VEHICLE SPEED BLUE – POWER ANTENNA
SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS
- ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR
20
IF NOT USING A MAESTRO HEAD UNIT ADAPTER: CUT AND DISCARD CONNECTOR
HEAD UNIT ADAPTER SOLD SEPARATELY
STEP 2
FACTORY RADIO HARNESS
USB ANTENNA ADAPTER
24
STEP 4
PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT.
MAIN HARNESS
CONNECT TO AFTERMARKET RADIO
OR
IF WIRES ARE PRESENT ON ADAPTER: SEE RADIO REFERENCE CHART
BACKUP CAM
ANTENNA ADAPTER USB ADAPTER
WIRES FROM VEHICLE
DATA AUDIO CABLE CABLE
MUS2 BEZEL
STEP 3
N.C. 3 YELLOW N.C. 3
2
2 BLACK
MIC 1 MIC 2
SYNC HARNESS 54
STEP 5
18
MAESTRO RR MODULE 4
4
AMP TURNON
N.C.
MUS2 T-HARNESS
NOT REQUIRED
18
A 12
10 3
4
STEERING WHEEL
CONTROL CABLE
4
3
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
7 maestro.idatalink.com
RADIO WIRE REFERENCE CHART
FORd Mustang InstallIng 8 OR 9 Inch scReen 2018-2023
MUS2 T-harness
Wire Description
Polarity
Wire Color on Maestro T-Harness
Wire Color on Alpine Wire Color on Kenwood/ Wire Color on Pioneer
cable
JVC cable
cable
Wire Color on Sony cable
Illumination
(+)
Reverse Light*
(+)
E-Brake
(-)
VSS (vehicle speed sensor) (DATA)
Power Antenna
(+)
Orange Purple/White
Lt Green Pink Blue
N/A Orange/White Yellow/Blue Green/White
Blue
Orange/White Purple/White
Lt Green Pink Blue
Orange/White Purple/White
Lt Green Pink
Blue/White
Orange Purple/White
Lt Green N/A
Blue or Blue/White
Head unit adapter wiring (optional accessory, sold separately)
ACC-HU-ALP1
Wire Description
Polarity Wire Color on Adapter
VSS (vehicle speed sensor) (DATA)
Green/White
Alpine Radio Green/White
ACC-HU-KEN1
Wire Description
Polarity Wire Color on Adapter
Kenwood Radio
CAM
(+)
CAM
(-)
Steering Wheel Controls
(DATA)
Green/Red Green/White Blue/Yellow
Refer to camera/radio manual
Refer to camera/radio manual
n/a
ACC-HU-KEN2
Wire Description
Polarity Wire Color on Adapter
Kenwood Radio
E-Brake
(-)
LtGreen
LtGreen
Reverse Light*
(+)
Purple/White
Purple/White
Steering Wheel Controls
(DATA)
Blue/Yellow
n/a
- Reverse light wire: Only connect to radio or module damage will occur.
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
8 maestro.idatalink.com
MODULE DIAGNOSTICS
LED 1
PROGRAMMING BUTTON
LED 2
FORd Mustang InstallIng 8 OR 9 Inch scReen 2018-2023
LED 1
LED 1 Module/Firmware status
· or · · · ·
·
LED 2 (RR2) Bluetooth activity
· ·
LED STATUS
RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes
OFF
DIAGNOSTIC
LED flashes 1 or more times, either red or green, when a steering wheel button
is pressed : normal operation. Module has no firmware. Flash module using
Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult
troubleshooting table.
After radio boots up : Normal operation.
Bluetooth is activated. Turns off after one minute: Normal operation. Normal
operation (inactive).
VIDEO HELP
Installation, product information, vehicle specific videos.
VERIFY FLASH
Last flash information, steering control configuration, vehicle information.
WEBLINK
Software to program module.
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
9 maestro.idatalink.com
FORd Mustang InstallIng 8 OR 9 Inch scReen 2018-2023
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
The light on the Maestro is blinking RED TWICE and the radio IS turning on.
Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.
Make sure the correct radio model and serial number were entered during the flash. Verify the radio’s serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.
The light on the Maestro is blinking RED TWICE but radio is NOT turning on.
If installing a modular radio and it is not turning on, ensure the screen is secured and any trim pieces on the radio have been installed fully. Not installing these fully will prevent radio from powering up and show a 2x red error as well. Test red and yellow wires for DC voltage at radio using a multimeter. Contact support if no voltage on red or yellow.
Center HVAC buttons sticking.
Ensure screws on back plate are not over tightened.
No backup camera image.
Verify position of yellow 2pin plug. 2015-2017- 12 pin Screen connector. 20182021- 54 pin SYNC connector.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the
module. Press and hold the module’s programming button and connect all the
connectors back to the module. Wait, the module’s LED will flash RED rapidly
(this may take up to 10 seconds). Release the programming button. Wait, the
LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE Phone:
1-866-427-2999 Email:
maestro.support@idatalink.com
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2023
ADS-RR(SR)-MUS2H-DS-IG-EN
10 maestro.idatalink.com
References
- iDatalink Maestro
- Sign in to your account
- Sign in to your account
- Weblink by ADS
- iDatalink Maestro
- iDatalink Maestro
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>