idatalink HRR-FO2 Maestro RR Ford Ranger with MyFord 4.3 inch Screen without AMP Installation Guide
- June 16, 2024
- idataLink
Table of Contents
idatalink HRR-FO2 Maestro RR Ford Ranger with MyFord 4.3 inch Screen
without AMP Installation Guide
HOW TO USE THIS INSTALL GUIDE
- Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.
- Print only the pages for your vehicle using the advanced options in the Print menu.
- Install your Maestro RR according to the guide for your vehicle.
WARNING
Pressing the printer icon or “quick printing” this document will print all of
the guides in this compilation.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
INSTALLATION INSTRUCTIONS
STEP 1
Remove the factory radio
If using head unit adapter (sold separately), connect HRRFO2 harness to
adapter and skip to step 2.
- Unbox the aftermarket radio and locate its main harness.
- Cut and remove the black 20 pin connector from the HRRFO2 T-harness and connect the wires, shown in the wiring diagram, from aftermarket radio main harness to the HRRFO2 T-harness and match the wire functions.
Note: only connect purple/white wire to radio reverse input or module damage will occur.
STEP 2
- Locate vehicle’s SYNC module harness in the center dash. Connect the 54-pin adapter harness to the vehicle.
- Connect the backup camera RCA to the 2-pin yellow connector
STEP 3
- Connect the factory radio harness to the HRR-FO2 T-harness.
STEP 4
- Connect the screen harness to the HRR-FO2 12-pin connector (B).
- Connect the yellow 2-pin connector to the HRR-FO2 backup camera cable.
- Connect the white 2-pin connector to the white 2-pin connector of HRR-FO2 main harness.
STEP 5
- Connect HRR-FO2 2-pin black connector to black connector of OBDII extension harness.
- Plug the OBDII connector into the OBDII of the vehicle.
STEP 6
- Plug the harnesses into the aftermarket radio.
- Connect the backup camera RCA cable into the aftermarket radio camera/BC video input.
- Plug the Data cable to the data port of the aftermarket radio.
- Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.
STEP 7
- Connect all the harnesses to the Maestro RR module then test your installation.
WIRING DIAGRAM
RADIO WIRE REFERENCE CHART
FO2 T-harness Wire Description| Polarity| Wire Color on
Maestro T-Harness| Wire Color on Alpine cable| Wire Color on
Kenwood cable| Wire Color on Pioneer cable| Wire Color on
Sony cable
---|---|---|---|---|---|---
Illumination| (+)| Orange| N/A| Orange/White| Orange/White| Orange
Reverse Light*| (+)| Purple/White| Orange/White| Purple/White| Purple/White|
Purple/White
E-Brake| (-)| Lt Green| Yellow/Blue| Lt Green| Lt Green| Lt Green
VSS (vehicle speed sensor)| (DATA)| Pink| Green/White| Pink| Pink| N/A
Power Antenna| (+)| Blue| Blue| Blue| Blue/White| Blue or Blue/White
Head unit adapter wiring (optional accessory, sold separately)
ACC-HU-ALP1 Wire Description| Polarity| Wire Color on
Adapter| Alpine Radio
---|---|---|---
VSS (vehicle speed sensor)| (DATA)| Green/White| Green/White
ACC-HU-KEN1 Wire Description
| Polarity| Wire Color on Adapter| Kenwood Radio
---|---|---|---
CAM| (+)| Green/Red| Refer to camera/radio manual
CAM| (-)| Green/White| Refer to camera/radio manual
Steering Wheel Controls| (DATA)| Blue/Yellow| n/a
ACC-HU-KEN2 Wire Description| Polarity| Wire Color on
Adapter| Kenwood Radio
---|---|---|---
E-Brake| (-)| LtGreen| LtGreen
Reverse Light*| (+)| Purple/White| Purple/White
Steering Wheel Controls| (DATA)| Blue/Yellow| n/a
- Reverse light wire: Only connect to radio or module damage will occur.
MODULE DIAGNOSTICS
LED 1 Module/Firmware status| LED 2 (RR2) Bluetooth
activity| LED STATUS| DIAGNOSTIC
---|---|---|---
or| | RED or GREENflashing| LED flashes 1 or more times, either red or green,
when a steering wheel button is pressed : normal
operation.
| | 1 RED flash| Module has no firmware.Flash module using Weblink Desktop and
log in. Do NOT use DEMO MODE.
| | 2 RED flashes| Problem detected. Consult troubleshooting table.
| | 1 GREEN flash| After radio boots up : Normal operation.
| | 3 GREEN flashes| Bluetooth is activated.Turns off after one minute: Normal
operation.
| | OFF| Normal operation (inactive).
VIDEO HELP| |
Installation, product information, vehicle specific videos.
---|---|---
VERIFY FLASH| | Last
flash information, steering control configuration, vehicle information.
WEBLINK| | Software to
program module.
TROUBLESHOOTING TABLE
| PROBLEM | SOLUTION |
|---|---|
| Gauges do not work, radio shows OBD2 Error 1 or Error 2. | Ensure OBDII |
connector is securely attached to the OBD2 connector of the vehicle.If you
hardwired connections at the OBDII, check connections at the OBDII connector.
Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is
connected to PIN 14 of the OBDII connector. Do not useT-Taps. Soldering or
military splicing methods are recommended.If anything else is connected to the
OBD2 or CAN wires of vehicle (programmer, throttle controller, insurance
tracker, etc.) try unplugging it to see if gauges work. If gauges work without
it installed, call tech support for options.Reset the RR.
There is no sound from OEM sources like Sync.| Ensure the all black, 3-pin to
3.5mm audio cable is connected between the RR and the radio. It connects to
the radio’s Idatalink I/F port, or AUX input if no I/F port is present.
There is no image from the backup camera and/or the steering wheel controls do
not work.| 4.3” MyFord vehicles – ensure the 12-pin connector from the 4.3”
factory screen is connected to the 12-pin plug of the T harness.HRR-FO2,
verify both the white and yellow connectors from the 12-pin harness are
connected to the main harness of the HRR-FO2.6.5” MyFord Touch vehicles –
ensure the camera and steering wheel connections are made at the Sync plug as
shown on the diagram.
The light on the Maestro is flashing RED ONCE.| There is no firmware on the
module. Flash the RR module using Weblink Desktop and log in. Do NOT use DEMO
MODE.
The light on the Maestro is blinking RED TWICE and the radio IS turning on.|
Ensure the 4-pin data cable is connected between the radio and the RR, and
that it is plugged into the black port on the Maestro RR. The red and blue
ports on the RR should be empty.Make sure the correct radio model and serial
number were entered during the flash. Verify the radio’s serial number entered
during the flash matches what is listed on the radio screen. This can be found
in the settings of the radio, listed as Device Id, Device Number, or Serial
Number.
The light on the Maestro is blinking RED TWICE but radio is NOT turning on.|
If installing a modular radio and it is not turning on, ensure the screen is
secured and any trim pieces on the radio have been installed fully. Not
installing these fully will prevent radio from powering up and show a 2x red
error as well.Test red and yellow wires for DC voltage at radio using a
multimeter. Contact support if no voltage on red or yellow.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the
module.
Press and hold the module’s programming button and connect all the connectors
back to the module. Wait, the module’s LED will fl ash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2
seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email:
maestro.support@idatalink.com
Web:
maestro.idatalink.com/support add
www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest fi rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.
PRODUCTS REQUIRED
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRR-FO2 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR02C-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
Click here for:
Radar Installation Guides
HEAD UNIT ADAPTER:
ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1
NEED HELP?
1 866 427-2999
maestro.support@idatalink.com
www.12voltdata.com/forum
References
- iDatalink Maestro
- iDatalink Maestro
- Index page
- Sign in to your account
- Sign in to your account
- Weblink by ADS
- iDatalink Maestro
- iDatalink Maestro
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>