idatalink BLADE-AL Network Programmable Data Immobilizer Integration Cartridge Installation Guide

: June 6, 2024
: idataLink

Table of Contents

INSTALL TYPE SELECTION
TYPE 1 – WIRE CROSS REFERENCE CHART
TYPE 1 – WIRING DIAGRAM
CARTRIDGE INSTALLATION
MODULE PROGRAMMING PROCEDURE
IDENTIFY VEHICLE YEAR
MODULE DIAGNOSTICS
FACTORY RESET PROCEDURE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Automotive Data Solutions Inc.
HK10
INSTALL GUIDE
COM-BLADE-AL(DL)-HK10-EN
AVAILABLE FOR: COM-BLADE AL
Rev. Date: May 28, 2021
Doc. No.: ##75784##
PATENT NO. US 8,856,780 CA 2759622
PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE PRODUCT DETAILS

HYUNDAI

NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiﬁed technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.

TERMS OF USE: automotive data Solutions inc. (“ADS”) products are strictly intended for installation by Certiﬁ ed Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an adS product in a vehicle, it is the Certiﬁ ed Technician’s responsibility to review the most current Product Guide, install Guide, and vehicle-speciﬁ c notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of proﬁ t, commercial loss, loss of economic opportunity, and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. Purchasers sole contractual remedy is refund of the purchase price of the adS product(s). adS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non- Certiﬁ ed Technicians, non-compliant Certiﬁ ed Technicians or end users.

INSTALL TYPE SELECTION

*Available only if vehicle is equipped with factory hood switch.

TYPE 1 – WIRE CROSS REFERENCE CHART

*(U.S. vehicles) connect only if vehicle is equipped with immobilizer.
**Optional connection

TYPE 1 – WIRING DIAGRAM

CARTRIDGE INSTALLATION

Slide cartridge into unit. Notice button under LED.
Ready for Module Programming Procedure.

MODULE PROGRAMMING PROCEDURE

1
| Turn key to ON position.
---|---
2| Wait, if LED turns solid BLUE, proceed with step 4.
If LED ﬂ ashes RED three times [3x], proceed with step 3.
3
| The vehicle’s immobilizer is NOT detected:
For USDM vehicles without an immobilizer, press and release programming button and proceed with step 4.
For CDM and USDM vehicles with an immobilizer, verify every wire connections and repeat the module programming procedure.
4
| Turn key to OFF position.
5| Module Programming Procedure completed.

IDENTIFY VEHICLE YEAR

Locate the Vehicle Identiﬁ cation Number (VIN), identify the 10th character then match it to its corresponding year.

MODULE DIAGNOSTICS

DIaGnoStIcS

| leD StatUS| DUrInG ProGraMMInG| DUrInG reMote Start| WItH IGnItIon off
---|---|---|---|---
| Flashing RED| Missing/wrong information from
ﬁ rmware or vehicle| Incorrectly programmed| Incorrectly programmed or connected
| Solid RED| Waiting for more vehicle information| Incorrectly programmed| Not programmed waiting for more
vehicle information
| Flashing BLUE| Additional steps required to complete
programming| Correctly programmed and operational| False ground when running status
from remote starter
| Solid BLUE then OFF| Correctly programmed| Reset in progress| Reset in progress
| OFF| No activity or already programmed| Invalid ground when running status
from remote starter| At rest and ready for a remote start
sequence

FACTORY RESET PROCEDURE

| DISCONNECT cartridge from remote starter.
---|---
| PRESS AND HOLD programming button while re-connecting
cartridge to remote starter.
| LED will ﬂ ash red. Immediately RELEASE programming button.
| LED will turn solid red for 2 seconds.
RESET COMPLETED.
5| RECONNECT all connectors. Repeat programming procedure.

Failure to follow procedure may result with a DTC or a
CHECK ENGINE error message.

WWW.IDATALINK.COM
Automotive Data Solutions Inc. © 2021