idatalink HRN-RR-SU2 Maestro AR Amplifier Replacement Module Installation Guide

: June 9, 2024
: idataLink

Table of Contents

HRN-RR-SU2 Maestro AR Amplifier Replacement Module
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HRN-RR-SU2 Maestro AR Amplifier Replacement Module

error
{
“error”: {
“message”: “You exceeded your current quota, please check your plan and billing details.”,
“type”: “insufficient_quota”,
“param”: null,
“code”: null
}
}

the following is the text from the user manual / instructions:
SELECT VEHICLE
PRINT PAGES NEEDED
HOW TO USE THIS INSTALL GUIDE
1 Open the Bookmarks menu and find your vehicle OR scroll
down until you find the install guide for your vehicle.
2 Print only the pages for your vehicle using the advanced
options in the Print menu.
3 Install your Maestro RR according to the guide for your vehicle.
WARNING
Pressing the printer icon or quick printing this document will print all of the guides in this compilation.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
INSTALL GUIDE
2013-2016 ScIOn FR-S
BaSe
RETAINS STEERING WHEEL CONTROLS, AND MORE!
OR
PRODUCTS REQUIRED
iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN- RR-SU2 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-SUB2-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
OPTIONAL ACCESSORIES
ELECTRONICS
Click here for: Radar Installation Guides
ACC-uSU2
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
TABLE OF CONTENTS
Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table
ScIOn FR-S BaSe 2013-2016
3 4 5 6 7
NEED HELP?
1 866 427-2999
maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum
ADS-RR(SR)-SUB02B-DS-IG-EN
2 maestro.idatalink.com
INSTALLATION INSTRUCTIONS P1/1
STEP 1
Note: only connect purple/white wire to radio reverse input or module damage will occur.
STEP 2
STEP 3
STEP 4
STEP 5
radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.
STEP 6
4 ADS-RR(SR)-SUB02B-DS-IG-EN
ScIOn FR-S BaSe 2013-2016 3 maestro.idatalink.com
ScIOn FR-S BaSe 2013-2016
WIRING DIAGRAM
STEP 1
CUT AND REMOVE THE RCA JACKS

ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR
WHITE – LF SPEAKER (+) WHITE/BLACK – LF SPEAKER (-) GRAY – RF SPEAKER (+) GRAY/BLACK – RF SPEAKER (-) GREEN – LR SPEAKER (+) GREEN/BLACK – LR SPEAKER (-) PURPLE – RR SPEAKER (+) PURPLE/BLACK – RR SPEAKER (-) BLUE/WHITE – AMP. TURN ON (+) BLACK – GROUND RED – ACCESSORY (+) YELLOW – 12V (+) ORANGE – ILLUMINATION (+) PURPLE/WHITE – REVERSE LIGHT (+) * LTGREEN – E-BRAKE (-) PINK – VEHICLE SPEED BLUE – POWER ANTENNA
SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS
STEP 2
YELLOW 2
BLUE 2
GREEN N.C.
2
GRAY GRAY
2
WHITE WHITE
2
PURPLE
NC
2
STEP 3
STARLINK
STEP 4
FACTORY RADIO HARNESS 6
10 28
rSU2 HARNESS VER. 1.7 + 8 PIN CONNECTOR BEHIND OEM RADIO PINK OR WHITE/BLUE – 08 OBDII CONNECTOR

SELECT VEHICLE
PRINT PAGES NEEDED
HOW TO USE THIS INSTALL GUIDE
1 Open the Bookmarks menu and find your vehicle OR scroll
down until you find the install guide for your vehicle.
2 Print only the pages for your vehicle using the advanced
options in the Print menu.
3 Install your Maestro RR according to the guide for your vehicle.
WARNING
Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

INSTALL GUIDE
2013-2016 ScIOn FR-S
BaSe
RETAINS STEERING WHEEL CONTROLS, AND MORE!
OR

PRODUCTS REQUIRED
iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN- RR-SU2 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-SUB2-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES
ELECTRONICS

Click here for: Radar Installation Guides

ACC-uSU2

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS
Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table

ScIOn FR-S BaSe 2013-2016
3 4 5 6 7

NEED HELP?
1 866 427-2999
maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2022

ADS-RR(SR)-SUB02B-DS-IG-EN

2 maestro.idatalink.com

INSTALLATION INSTRUCTIONS P1/1
STEP 1
· Unbox the aftermarket radio and locate its main harness. · Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. · Connect the wires from aftermarket radio main harness to
the SU2 T-harness and match the wire functions. · Remove the factory radio.
Note: only connect purple/white wire to radio reverse input or module damage will occur.
STEP 2
· Assemble the SU2 T-harness and connect it to the factory radio harness.
STEP 3
Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button. · Connect the BROWN Starlink wire to PINK or WHITE/BLUE (pin 8) of the 8 pin connector behind the OEM Radio.
STEP 4
· Plug the OBDII connector into the OBDII of the vehicle, under driver dash.
STEP 5
· Plug the aftermarket radio harnesses into the aftermarket radio.
· Plug the AUX cable to the aftermarket radio. · Plug the RCA cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket
radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.
STEP 6
· Connect all the harnesses to the Maestro RR module then test your installation.

4 ADS-RR(SR)-SUB02B-DS-IG-EN

ScIOn FR-S BaSe 2013-2016 3 maestro.idatalink.com

ScIOn FR-S BaSe 2013-2016

WIRING DIAGRAM

STEP 1

CUT AND REMOVE THE RCA JACKS

ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR

WHITE – LF SPEAKER (+) WHITE/BLACK – LF SPEAKER (-) GRAY – RF SPEAKER (+) GRAY/BLACK – RF SPEAKER (-) GREEN – LR SPEAKER (+) GREEN/BLACK – LR SPEAKER (-) PURPLE – RR SPEAKER (+) PURPLE/BLACK – RR SPEAKER (-) BLUE/WHITE – AMP. TURN ON (+) BLACK – GROUND RED – ACCESSORY (+) YELLOW – 12V (+) ORANGE – ILLUMINATION (+) PURPLE/WHITE – REVERSE LIGHT (+) * LTGREEN – E-BRAKE (-) PINK – VEHICLE SPEED BLUE – POWER ANTENNA

SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS

STEP 2

YELLOW 2
BLUE 2

GREEN N.C.

2

GRAY GRAY

2

WHITE WHITE

2

PURPLE

NC

2

STEP 3
STARLINK
STEP 4

FACTORY RADIO HARNESS 6
10 28
rSU2 HARNESS VER. 1.7 + 8 PIN CONNECTOR BEHIND OEM RADIO PINK OR WHITE/BLUE – 08 OBDII CONNECTOR

STEP 5
MAIN HARNESS

PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED
IN W/R PORT.
CONNECT TO AFTERMARKET RADIO

AUX

C

BACKUP CAM

WIRES FROM VEHICLE

DATA CABLE

STEP 6
MAESTRO RR MODULE

2 NC NC

2
SU2 T-HARNESS
4

NOT REQUIRED A
D

B
AUDIO CABLE

STEERING WHEEL CONTROL CABLE

ADS-RR(SR)-SUB02B-DS-IG-EN

4 maestro.idatalink.com

RADIO WIRE REFERENCE CHART

ScIOn FR-S BaSe 2013-2016

Wire Description

Polarity

Wire Color on Maestro T-Harness

Wire Color on Alpine cable

Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination

(+)

Reverse Light

(+)

E-Brake

(-)

VSS (vehicle speed sensor) (DATA)

Power Antenna

(+)

Orange Purple/White
Lt Green Pink Blue

N/A Orange/White Yellow/Blue Green/White
Blue

Orange/White Purple/White
Lt Green Pink Blue

Orange/White Purple/White
Lt Green Pink N/A

ADS-RR(SR)-SUB02B-DS-IG-EN

5 maestro.idatalink.com

MODULE DIAGNOSTICS

LED 1

PROGRAMMING BUTTON
LED 2

ScIOn FR-S BaSe 2013-2016

LED 1

LED 1 Module/Firmware status
· or · · · ·
·

LED 2 (RR2) Bluetooth activity
· ·

LED STATUS
RED or GREEN flashing 1 RED flash 2 RED flashes 1 GREEN flash 3 GREEN flashes OFF

DIAGNOSTIC
LED flashes 1 or more times, either red or green, when a steering wheel button is pressed : normal operation. Module has no firmware. Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE. Problem detected. Consult troubleshooting table.
After radio boots up : Normal operation.
Bluetooth is activated. Turns off after one minute: Normal operation. Normal operation (inactive).

VIDEO HELP

Installation, product information, vehicle specific videos.

VERIFY FLASH

Last flash information, steering control configuration, vehicle information.

WEBLINK

Software to program module.

ADS-RR(SR)-SUB02B-DS-IG-EN

6 maestro.idatalink.com

TROUBLESHOOTING TABLE P1/2

ScIOn FR-S BaSe 2013-2016

PROBLEM

SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2.

Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

If anything else is connected to the OBD2 or CAN wires of vehicle (programmer, throttle controller, insurance tracker, etc.) try unplugging it to see if gauges work. If gauges work without it installed, call tech support for options.

Backup camera is not displayed. Radio switches to blank screen.

Reset the RR.
Verify factory radio screen size (diagonally, if mentioned in the guide) and vehicle listed at top right corner of the guide matches the vehicle. There are 3 different camera connection options based on vehicle, screen, etc.

Starlink connector isn’t present.

Some vehicles show Starlink on the radio screen when booting, but do not have the buttons present in the vehicle overhead console. If buttons are not present, the vehicle does not have Starlink. This connection is only required when equipped with Starlink.

Front speakers do not play but rears do.

Reconnect the factory Starlink module. It is mounted below the factory radio, on its metal mounting brackets. This module must remain in the vehicle. Ensure that all connections (connectors or wires) are done exactly as shown in step 2.

Vehicle has Harman Kardon system and no sound.

Ensure the BLUE/WHITE amp turn-on wire is connected. Ensure the 6-pin connector (plug with blue, green, green/black, purple, and purple/black wires) on the T-harness is not connected to the car.

Radio turns on but will not turn off, even with doors opened. (Vehicles with CAN connections at the climate controls only, refer to wiring diagram).

Verify CAN connections at the climate controls have been made. The BROWN/RED and BROWN/YELLOW wires need to be cut in the harness. Maestro RR side of those wires should be extended to the climate control harness, as shown in the diagram. CAN wires should be next to each other in the plug, not on top of one another. Some vehicles have a wire below pin 1 that matches the color for pin 2.

The light on the Maestro is blinking RED TWICE and the radio IS turning on.

Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the flash. Verify the radio’s serial number entered during the flash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

The light on the Maestro is blinking RED TWICE but radio is NOT turning on.

If installing a floating screen type radio and it is not turning on, ensure the screen is secured and any trim pieces on the radio have been installed fully. Not installing these fully will prevent radio from powering up and show a 2x red error as well. Test red and yellow wires for DC voltage at radio using a multimeter. Contact support if no voltage on red or yellow.

The light on the Maestro is flashing RED ONCE.

There is no firmware on the module; flash the RR module.

ADS-RR(SR)-SUB02B-DS-IG-EN

7 maestro.idatalink.com

TROUBLESHOOTING TABLE P2/2

ScIOn FR-S BaSe 2013-2016

MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: maestro.support@idatalink.com Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

ADS-RR(SR)-SUB02B-DS-IG-EN

8 maestro.idatalink.com

INSTALL GUIDE
2013-2016 ScIOn FR-S
wIth aMP
RETAINS STEERING WHEEL CONTROLS, AND MORE!
OR

PRODUCTS REQUIRED
iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN- RR-SU2 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-SUB2-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide

OPTIONAL ACCESSORIES
ELECTRONICS

Click here for: Radar Installation Guides

ACC-uSU2

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

WELCOME
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

TABLE OF CONTENTS
Installation Instructions Wiring Diagram Radio Wire Reference Chart Module Diagnostics Troubleshooting Table

ScIOn FR-S wIth aMP 2013-2016
3 4 5 6 7

NEED HELP?
1 866 427-2999
maestro.support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2022

ADS-RR(SR)-SUB02B-DS-IG-EN

2 maestro.idatalink.com

ScIOn FR-S wIth aMP 2013-2016

INSTALLATION INSTRUCTIONS P1/1

STEP 1
· Unbox the aftermarket radio and locate its main harness. · Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. · Connect the wires from aftermarket radio main harness to
the SU2 T-harness and match the wire functions. · Remove the factory radio.

STEP 6
· Connect all the harnesses to the Maestro RR module then test your installation.

Note: only connect purple/white wire to radio reverse input or module damage will occur.

STEP 2
· Assemble the SU2 T-harness and connect it to the factory radio harness.
rSU2 V1.7+ harness : Unplug the gray 2 pin connectors and plug the female gray 2 pin into the male green 2 pin connector.
rSU2 V1.5 or below harness : Locate the 28 pin connector on the SU2 T-harness. Cut the Brown/Red wire (pin 9). Tape/insulate the Brown/Red wire (Maestro side of cut). Connect Brown/Red wire (vehicle side of cut) to the Blue/ White wire from the aftermarket radio main harness.
STEP 3
Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button. · Connect the BROWN Starlink wire to PINK or WHITE/BLUE (pin 8) of the 8 pin connector behind the OEM Radio.
STEP 4
· Plug the OBDII connector into the OBDII of the vehicle, under driver dash.

STEP 5
· Plug the aftermarket radio harnesses into the aftermarket radio.
· Plug the AUX cable to the aftermarket radio. · Plug the RCA cable to the aftermarket radio. · Plug the Data cable to the data port of the aftermarket
radio. Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port.
12

ADS-RR(SR)-SUB02B-DS-IG-EN

3 maestro.idatalink.com

ScIOn FR-S wIth aMP 2013-2016

WIRING DIAGRAM

STEP 1

CUT AND REMOVE THE RCA JACKS

ONLY CONNECT TO RADIO REVERSE INPUT OR MODULE DAMAGE WILL OCCUR

WHITE – LF SPEAKER (+) WHITE/BLACK – LF SPEAKER (-) GRAY – RF SPEAKER (+) GRAY/BLACK – RF SPEAKER (-) GREEN – LR SPEAKER (+) GREEN/BLACK – LR SPEAKER (-) PURPLE – RR SPEAKER (+) PURPLE/BLACK – RR SPEAKER (-) BLUE/WHITE – AMP. TURN ON (+) BLACK – GROUND RED – ACCESSORY (+) YELLOW – 12V (+) ORANGE – ILLUMINATION (+) PURPLE/WHITE – REVERSE LIGHT (+) * LTGREEN – E-BRAKE (-) PINK – VEHICLE SPEED BLUE – POWER ANTENNA BLUE/WHITE – AMP. TURN ON (+)

SEE RADIO WIRE REFERENCE CHART FOR RADIO WIRE COLORS

STEP 5
MAIN HARNESS

STEP 2

YELLOW 2
BLUE 2

GREEN

GREEN N.C.

2

2 GRAY

unplug GRAY

C FACTORY RADIO HARNESS
6
10

AUX BACKUP CAM
WIRES FROM VEHICLE

28

PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED
IN W/R PORT. CONNECT TO AFTERMARKET RADIO
DATA CABLE

WHITE WHITE

2

PURPLE

NC

2

rSU2 HARNESS VER. 1.7 +

CUT BROWN/RED WIRE (PIN 9)
rSU2 HARNESS VER. 1.5 –

STEP 3
STARLINK
STEP 4
2 NC NC

8 PIN CONNECTOR BEHIND OEM RADIO PINK OR WHITE/BLUE – 08
OBDII CONNECTOR

STEP 6

MAESTRO RR MODULE

2
12
SU2 T-HARNESS

NOT REQUIRED A

AUDIO CABLE

STEERING WHEEL CONTROL CABLE

B D