Raingler NETS GRIPS 2017 0 Newer Honda CR-V Behind Front Seat Barrier Installation Guide
- June 8, 2024
- Raingler NETS GRIPS
Table of Contents
NETS GRIPS 2017 0 Newer Honda CR-V Behind
Front Seat Barrier
Installation Guide
2017 0 Newer Honda CR-V Behind Front Seat Barrier
NOTE: Many newer models have B-pillar handles and even overhead on the ceiling that can be used for some of the top mounting locations. Check to see if you prefer to use these factory locations as the nets typically have enough adjustment to allow for this option. If your vehicle does not have handles in desired locations or you prefer to install mounting points for better fitment, please follow the below steps.
IMPORTANT: READ INSTRUCTIONS FULLY BEFORE STARTING
Time: 60-90 minutes
Paw Level:
Tools:
- Panel Removal tool
- Drill
- High Quality, Sharp, Assorted Bits including 3/16”
- Hammer
- Punch
Required Hardware (included):
- C100S
Step 1
Slide front seats all the way forward for best access. Grasp the top of the
darker lower cover on the B pillar and carefully pull back towards center of
interior. It is easier to start at one side by the rubber weatherstripping.
Watch for plastic inserts that attach panels to the inner metal structure and
snap into existing holes. We recommend picking up an extra pair of these
nylon pieces (PART #C116TN – click link here) when you order in case any get
lost or snap during disassembly. 
Step 2
Pull the top weatherstripping rubber loose at the inside corners next to the
lighter grey upper B pillar section.
Step 3
Remove the lighter upper panel at the edge of the weather stopping to loosen
each side.
NOTE that you will need to twist and pivot the upper shoulder seat belt
roller to orient through the panels slotted opening:
Panel removed and laid back out of the way —- →
NOTE: The white plastic snap in is very difficult to remove and so we recommend a strong metal removal tool to pop it out. Reinstall this white insert back into the upper cover panel.
Step 4
Line up the C100S Footman just below the headliner material and mark the hole
location either with the punch or a marker.
Step 5
Use a hammer and punch to indent the location to mount thefootman’s screws:
Step 6
Drill the holes in incremental steps until you get to the proper size for the
screws. These supplied #12 screws need a 3/16 hole to properly thread and seat
without being too tight. *Attempting to power drive the screws through too
small a hole will likely snap the screw. Sharp drill bits and care and
patience are key here on the hardest step of the process. Go slow and be
careful that you don’t use too long a drill bit as to damage the exterior of
the vehicle. There is plenty of room but check twice and drill once.
Since the holes are right at the edge of the flat part of the mounting
surface, one screw was installed before punching and drilling second hole.
Mount the C100S hardware and reassemble upper trim cover, rubber water
stripping and then lower cover making sure that the plastic push ins are
installed into the cover panels and line up to the holes. Remember how you
oriented the upper seat belt roller assembly through the panels opening.
Make sure that the tether of the C100S is clear and accessible when the panels
are reinstalled.
Step 7
Loosely install your net, generally with the logo facing the rear of the
cabin. 
Lower strap goes under seat bracket:
*If you have the top quick release hooks you may have to adjust the tension so that you can lift the hook out of the pillar mounted C100S D ring.
Step 8
Slide front seats back into normal driving position and then tight and center
the net by drawing the top straps taut and then the lower straps. Wrap up the
excess straps as shown in this short video: https://vimeo.com/316588617
Step 9
Your net should now be done and look like this:
Step 10
Please enjoy your net and let us know if any questions or share and tag us on
social media when you get a chance to have your vehicle loaded up with gear or
pups!
Thank you for purchasing Raingler Nets.
If you have any questions please contact us, we are here to help!
See all our install videos on Vimeo!
https://vimeo.com/raingler
866-905-7625 |
Tech@RAINGLER.com |
Raingler.com
References
- Cargo, barrier and dog safety nets - Raingler Nets
- Tying Up Loose Ends on Vimeo
- Raingler Nets & Barriers
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>