SATCO 60-7663 Pendant Light Instruction Manual
- June 8, 2024
- SATCO
Table of Contents
SATCO 60-7663 Pendant Light Instruction Manual
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house electrical wires, nor
should a swag type fixture be installed on a ceiling which contains a radiant
type heating system.
Read instructions carefully.
If you are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all parts are
included as shown in figure.
Be careful not to misplace any of the screws or parts, which are needed to
install this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
- STEP 1: Thread mounting screw into the matching holes in the mounting bracket.
- STEP 2: Secure mounting bracket to outlet box with the outlet box screws.
GROUNDING INSTRUCTIONS
-
STEP 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar.
Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied).
If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES. -
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
GROUP A:
Connect to Black House Wire| GROUP B:
Connect to White House Wire
---|---
BLACK| WHITE
PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is
square shaped or ridged and the less tracer wire is round in
shape or smooth (seen best when viewed from wire end.)
-
STEP 3: Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box.
Do NOT twist wires together before using wire connectors. -
STEP 4: Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
-
STEP 5: Try gently to pull the connector off the wires.
If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture. -
STEP 6: Connect the fixture wire from group B to the white wire from the outlet box in the same manner.
Make sure no bare wires can be seen outside wire connectors.
FINAL ASSEMBLY
-
STEP 1: After wires are connected, tuck them carefully inside outlet box.
Raise canopy aligning the hole on the mounting bar all the way through the hole on the canopy, tighten the mounting screws until the fixture is held firmly against the wall. -
STEP 2: Install lamp (not included). Please do not exceed the maximum capacity recommended on the socket.
-
STEP 3: Attached the glass to the lamp shade and secure with clips.
-
STEP 4: Fix the lamp shade with ball nuts.
CLEANING
To clean, wipe fixture with a soft cloth.
Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders, steel wool or
abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts.
Be sure to use exact wording from illustration when ordering parts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>