QFX BT-ZX1 Wireless Speaker Instruction Manual

BT-ZX1
WHERE THE PARTY BEGINS™
ISTRUCTION MANUAL

BT-ZX1 Wireless Speaker

Thank you for purchasing the BT-ZX1 Wireless Speaker. Please read this user manual carefully and keep it for future reference.

Product Diagram

Specifications

HFP V1.7, HID V1.1, IOPT, SPP V1.2
Audio Output Power| 2 × 5W
Frequency Response| 80Hz – 20KHz
Signal-to-Noise Ratio| ≥ 65dB
Input| DC 5V
Charging Time| 3 hours
Battery Life| Up to 24 hours
Battery Type| Li-ion Rechargeable (2200mAh)
Operating Range| Up to 33ft / 10m
Dimensions| L 175mm × W 50mm × H 67mm
Weight| 360±20g

Getting Started

Charging the Speaker
Fully charge the speaker before the first use. Supply the BT-ZX1 with power using the provided USB-type C cable. The LED indicator will turn solid red while charging and turn off when fully charged. A full charge takes about 3 hours.

Controls & LED Indicator
AUX Mode

iPhone, not Android)
Play or pause| Press the multi-function button

BT Mode

iPhone, not Android)
Skip to next/previous
track| Press and hold volume + / – for 2 seconds
Answer or end the call| Short-press the multi-function button
Reject an incoming call| Press and hold the multi-function button for 2 seconds
Redial last-outgoing-called
number| Double-click the multi-function button in stand-by
Disconnect BT| Long-press the multi-function button

TWS Mode

seconds
Turn speaker off| Press and hold the power button of any speaker for 2 seconds
Enter or exit TWS mode| Double-click the power button of the home speaker
Play or pause| Short-press the multi-function button of any of the two speakers
Adjust volume| Short-press the volume + / – of any of the two speakers (synchronized with the volume of the iPhone, not Android)
Skip to next/previous track| Press and hold volume + / – of any of the two speakers
Answer or end the call| Short-press the multi-function button of the home speaker
Reject an incoming call| Press and hold the multi-function button of the home speaker for 2 seconds
Redial last-outgo-
ing-called number| Double-click the multi-function button of the home speaker in stand-by
Disconnect BT| Press and hold the multi-function button of any of the two speakers for 2 seconds

Power On / Off

• Press and hold the power button for 2 seconds to turn on/off the speaker

Pairing

1. When you turn on the speaker, it will automatically enter pairing mode.
2. Activate the pairing function on your phone and select “QFX BT-ZX1”.
3. If a code or pin is required for pairing, enter ”0000” as the default code.
4. When successfully paired, you will hear a beep.

Note

• If you want to use another device to connect to the BT-ZX1, please press and hold the multi-function button “Play/Pause” for 2 seconds to disconnect BT-ZX1 from the current device. Then repeat the “pairing” steps.
• When you turn the speaker on, it will automatically reconnect to the last-paired device. You can also enter pairing mode if no device is found.
• When the speaker is paused, or there is no Bluetooth connection, the speaker will automatically shut down after 10 minutes
• If the speaker or connected device exceeds the operating range, the speaker will disconnect. The connection to the last successfully connected device will be re-established once you re-enter the wireless range within 10 minutes.

Playing Audio via Audio Input Connection
Connect the BT-ZX1 to your PC, laptop, or other devices with the audio output port using the included 3.5mm audio cable.

Note

• The speaker will disconnect from your phone or other paired devices when an audio cable is plugged into the audio input jack. Press the power button to switch back to BT mode
• When playing audio using the audio input jack, press the volume + / – to adjust the volume and short-press the multi-function “Play/Pause” button to pause or resume. Next/previous track control on the speaker is disabled in audio input mode
• For some computers, you may need to access the audio control panel to manually set the speaker as the default audio device

TWS Mode

1. Turn on two BT-ZX1 speakers at the same time, double-click the power button of one of the speakers to automatically enter the TWS pairing mode, a tone will be heard every three seconds.
2. During the TWS pairing process, double-click the power button to cancel the TWS pairing. If the TWS pairing exceeds 60 seconds and the TWS pairing is not successful, it will automatically return to the normal BT mode.
3. After the TWS pairing is successful, one of the speakers LED light will turn on (this is the satellite) and the other will begin flashing (this is the home). You will hear the BT beep sound after.
4. Activate the pairing function on your phone or other compatible device and select “BT-ZX1”
5. If a code or pin is required for pairing, enter “0000”
6. When successfully paired, you will hear a beep.

Note

• When the phone is connected to the Bluetooth of one of the speakers first, you need to double-click the power button of the speaker connected to the phone to enter the TWS pairing mode
• After the TWS pairing is successful, double-click the power button on one of the speakers to automatically exit the TWS pairing mode. The BT connection between the home speaker and phone will not disconnect.

Follow Us QFXUSA.COM

| 1-800-864-CLUB (2582)
Mon-Fri 9AM – 5PM (PST)
---|---
| support@qfxusa.com
Mon-Fri 9AM – 5PM (PST)

    WHERE THE PARTY BEGINS™

Product Care & Use

• Keep away from extreme heat and strong magnetic fields
• Do not use this speaker at high volume for extended periods, as this may cause permanent hearing damage or hearing loss

FCC ID: 2ATIH-SK-A2

Documents / Resources

| QFX BT-ZX1 Wireless Speaker [pdf] Instruction Manual
BT-ZX1, Wireless Speaker, BT-ZX1 Wireless Speaker, Speaker
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>