Danby DDEF02213BD13 Electric Fireplace With Heater Owner’s Manual

: June 8, 2024
: Danby

Table of Contents

Danby DDEF02213BD13 Electric Fireplace With Heater
Important Safety Information
OPERATING INSTRUCTIONS
- INCLUDED ACCESSORIES
- CONTROL PANEL
INSTALLATION INSTRUCTIONS
- EMBER BED INSTALLATION
CARE & MAINTENANCE
TROUBLESHOOTING
LIMITED “CARRY IN” WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Danby DDEF02213BD13 Electric Fireplace With Heater

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

WARNING: Read and understand this entire owner’s manual, including all safety information, before plugging in or using this ﬁreplace. Failure to do so could result in ﬁ re, electric shock or serious personal injury.
CAUTION: Keep this owner’s manual for future reference.
CAUTION: Risk of electric shock. Do not open or try to repair the ﬁreplace yourself.
This ﬁreplace may get hot when in use. To avoid burns, do not let bare skin touch hot surfaces.
Keep combustible materials, such as furniture, pillows, bedding, paper, clothes and curtains at least 3 feet from the front of the ﬁreplace and keep them away from the sides, top and rear. Do not place towels or other objects on the ﬁreplace.
Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
The ﬁ replace is not intended for use in bathrooms, laundry areas, showers or swimming pools and similar locations. Never locate the ﬁ replace where it may fall into a bathtub or other water container. To protect against electrical hazards, do not immerse the power cord in water or other liquids.
Do not touch the control panel or plug with a wet hand.
Always use on a dry, level surface.
Do not use outdoors.
Always use in an upright position.
Do not attempt to repair or adjust any electrical or mechanical functions on this ﬁreplace. Doing so will void your warranty. The inside of the ﬁ replace does not contain any user-serviceable parts.
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or ﬁ re or damage to the ﬁ replace.
WARNING: To reduce the risk of ﬁ re or electric shock, do not use this ﬁ replace with any solid-state speed control devices.
Do not operate any ﬁ replace with a damaged power cord or after the ﬁ replace malfunctions, has been dropped or damaged in any manner. Return the ﬁ replace to an authorized service facility for examination, electrical or mechanical adjustment or repair.
Do not run the power cord under carpeting. Do not cover the power cord with throw rugs, runners or similar coverings. Arrange the power cord away from trafﬁcarea where it will not be tripped over.
To prevent possible ﬁ re, do not block the air intakes or exhaust in any manner. Do not use the ﬁ replace on soft surfaces like a bed or thick carpeting where the air intakes may become blocked.
This ﬁreplace has hot and arcing or sparking parts inside. Do not use the ﬁ replace in areas where gasoline, paint, explosive and/or ﬂammable liquids are used or stored. Keep the ﬁ replace away from heated surfaces and open ﬂames.
To avoid ﬁ re or shock hazard, plug the ﬁreplace directly into a 120 V AC electrical outlet. Never use an extension cord or power strip.
To disconnect the ﬁ replace, turn the controls to off and then remove the plug from the outlet. Pull ﬁrmly on the plug, do not unplug by pulling on the cord.
Always unplug the ﬁ replace before moving or cleaning it. Unplug the ﬁreplace when it is not in use.
Use only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause ﬁre, electric shock or injury to persons. The use of attachments is not recommended.

OPERATING INSTRUCTIONS

OVERHEAT SAFETY FEATURE
This ﬁreplace is equipped with an overheat safety feature. When the ﬁreplace’s internal components reach a certain temperature that could cause overheating and possible ﬁ re, the ﬁ replace will automatically shut off. Operation can only resume when the user resets the ﬁ replace.

To reset the ﬁ replace, ensure the power is turned off, unplug the unit and wait 15 to 20 minutes for the internal components to cool down.
Follow the instructions for use to return the ﬁ replace to normal functioning.

WARNING: It is normal for the power cord to feel warm to the touch; however, a loose ﬁ t between the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a different outlet. Contact a qualiﬁ ed electrician to inspect the original outlet for damage.

INCLUDED ACCESSORIES

Electric ﬁ replace with heater
Remote control
Clear crystals
Wall hanging bracket
Wall hanging bracket hardware:
4 x 45 mm screws x3
Three screw expansion brackets
4 x 12 mm screws x2
Two feet
4 x 16 mm screws x8 (to assemble feet)

FEATURES

Glass
Air outlet
Wall hanging bracket holder
Ember bed
Free-standing feet

IMPORTANT WARNING
Do not leave this appliance unattended in a space where people or animals who cannot react to a malfunction are located. A malfunction can cause extreme overheating or death in an enclosed, unattended space.

CONTROL PANEL

Power indicator light: Illuminates to show the ﬁ replace is turned on.
1/2 hour timer indicator light
1-hour timer indicator light
2-hour timer indicator light
4-hour timer indicator light
Low heat indicator light: Illuminates when low heat mode is set.
High heat indicator light: Illuminates when high heat mode is set.
Power button: Press to turn the ﬁ replace on or off.
Flame button: Press to turn the ﬂsame on or off and to change the ﬂame colour. There are 10 ﬂame colours. Press and hold for 5 seconds to set the colours to cycle continuously.
Ember bed button: Press to turn the carbon bed on or off and to change the colour. There are 10 ember colours. Press and hold for 5 seconds to set the colours to cycle continuously.
Light button: Press to adjust the ﬂ ame brightness. There are 5 brightness levels.
Heater button: Press repeatedly to select low or high heat mode. The adjacent indicator light will illuminate to display the chosen mode.
Timer button: Press repeatedly to set the timer. The timer will turn
the ﬁ replace off after the chosen time. The timer can be set in 1/2 hour increments up to 7.5 hours. The adjacent indicator lights will illuminate to display the chosen setting.
Thermostat button: Turn to set the temperature. The thermostat can only be set from the control panel on the ﬁreplace.

Danby DDEF02213BD13 Electric Fireplace With Heater-2

REMOTE CONTROL

Power button: Press to turn the ﬁreplace and ﬂame on or off.
Heater button: Press repeatedly to select low or high heat mode.
Flame button: Press to turn the ﬂame on or off and to change the ﬂame colour.
Ember bed button: Press to turn the carbon bed on or off and to change the colour.
Timer button: Press repeatedly to set the timer. The timer will turn the ﬁ replace off after the chosen time. The timer can be set in 1/2 hour increments up to 7.5 hours.
Light button: Press to adjust the ﬂame brightness. There are 5 brightness levels.

REMOTE CONTROL BATTERY
This remote control uses one CR2025 battery.
To remove the battery, push the latch on the battery compartment upwards and then pull the battery tray out.
To replace the battery, place the new battery in the battery tray and push it gently into the remote control until it clicks into place.

WARNING:

Keep batteries out of childrens’ reach. Discard them carefully.
Do not allow children to play with batteries.
Never put button batteries in or near your mouth for any reason, they are slippery and easy to swallow accidentally.

WARNING: Never dispose of batteries in ﬁ re. Failure to observe this precaution may result in an explosion. Dispose of batteries at your local hazardous material processing center.

If the ﬁ replace will not be used for a long time, remove the batteries to prevent corrosion. Store the remote control in a safe place.
Remove the insulating ﬁ lm from the battery compartment before using the remote control.

INSTRUCTIONS FOR USE

Remove the insulating ﬁ lm from the remote control battery compartment.
Ensure the power is turned off.
Decide which installation method to use and install the ﬁ replace as directed.
Plug the ﬁ replace directly into a 120V AC electrical outlet.
Turn the ﬁ replace on by pressing the power button.
Press the heater button to set low or high heat mode.
Turn the thermostat dial to set the desired temperature. The ﬁ replace will remain on until the set temperature is reached and it will then cycle on and off to maintain the set temperature.
Turn the ﬁ replace off by pressing the power button. When the power is turned off the heating element will stop working immediately but the fan will continue to run for 30 seconds or until the ﬁ replace has cooled.

Important
When the heat feature is used for the ﬁ rst time, a slight odor may be present. This is normal and should not occur again unless the ﬁ replace is not used for an extended period of time.
It is normal for the ﬁ replace to cycle on and off as it maintains the set temperature.
For the ﬁ replace to function properly, the set temperature must be higher than the ambient temperature in the room. If the ﬁreplace does not seem to be heating, increase the set temperature to engage the heating element.

INSTALLATION INSTRUCTIONS

PREPARATION

WARNING: This product includes glass. Always use extreme caution when handling glass. Failure to do so could result in personal injury or property damage.
Remove all parts and hardware from the carton and place them on a clean, soft, dry surface.

WARNING: Make sure all parts are dry and the power cord and plug are not damaged. See the Important Instructions section.
The ﬁ replace can be wall-mounted or placed on a solid, level surface when the free-standing feet are assembled. The ﬁreplace must be plugged into a 120V 60Hz electrical outlet.

FREE-STANDING FOOT ASSEMBLY
Place the ﬁ replace carefully on its back. Place the ﬁ replace on a blanket or soft surface to avoid scratching the unit or ﬂ ooring.
Attach the free-standing feet using eight 4 x 16 mm screws as shown. Place upright on a solid, level surface and plug into a 120V 60Hz electrical outlet.
Note: If you attach the solid feet for freestanding installation, you do not need to install the wall bracket onto the back of the ﬁreplace.

WALL MOUNTED INSTALLATION
Find a safe location to install the ﬁ replace. To prevent ﬁ re there must be a minimum clearance of 50 cm (20 inches) on the sides and bottom and 100 cm (40 inches) on the top of the unit.
Choose a location near an outlet so an extension cord is not required. Do not position the ﬁ replace directly below a power outlet.
WARNING:

Prior to wall mounting, check the wall to ensure that there are no wires, pipes or similar in the area where holes will be drilled.
WARNING: Ensure the ﬁ replace is unplugged prior to installation, moving and assembling.
WARNING: This ﬁ replace cannot be recessed into a hollow wall cavity. Mountings must be secured to a solid wall surface such as plasterboard or drywall that is supported by studs spaced no more than 24 inches (60 cm) apart.

Note: Ensure the feet are not installed before attempting a wall installation.

The glass should be removed before installation. Remove the two thumbscrews on the top left and top right side of the glass.
Lift the glass panel upward to remove it.
Attach the wall hanging bracket to the wall using three 4 x 45 mm screws and three supplied screw expansion brackets. The screws should be evenly spaced across the available locations in the wall bracket. Ensure that at least one screw enters a wall stud.
Lift the ﬁ replace into position using two people. Ensure that the tabs on the back of the ﬁ replace securely engage with the slots provided. Use two 4 x 12 mm screws to attach the ﬁ replace to the wall hanging bracket. The screws can be found in the accessory bag and one should be used on each side of the panel.
Replace the glass on the front of the ﬁ replace, ensuring the locating tabs engage securely in their corresponding slots and that the thumbscrews are tightened.

Danby DDEF02213BD13 Electric Fireplace With Heater-7

EMBER BED INSTALLATION

WARNING: The next step involves glass. Always use extreme caution when handling glass. Failure to do so could result in personal injury or property damage.
This ﬁreplace will come with the faux log bed pre-installed. To change to the provided clear crystals, follow the steps below.

The glass should be removed before installation. Remove the two thumbscrews on the top left and top right side of the glass.
Lift the glass panel upward to remove it.
Remove the two screws from each side of the faux log bed.
Remove the faux log bed and replace the screws. Spread the clear crystals onto the ember bed.
Replace the glass on the front of the ﬁ replace, ensuring the locating tabs engage securely in their corresponding slots and that the thumbscrews are tightened

CARE & MAINTENANCE

CLEANING

Ensure the power is turned off and the ﬁ replace is unplugged.
Allow the ﬁ replace to completely cool before attempting any cleaning.
The outer shell may be cleaned with a soft, damp cloth. A mild detergent can be used if necessary. After cleaning, dry the ﬁ replace with a soft cloth. Do not let liquid enter the ﬁ replace.
Wait until the ﬁ replace is completely dry before using.

WARNING: Do not immerse the ﬁ replace in water or allow water to enter the ﬁ replace.

WARNING: Do not use alcohol, gasoline, abrasive powders, furniture polish or rough brushes to clean the ﬁ replace. This may cause damage or deterioration to the surface of the ﬁ replace.

STORAGE
Store the ﬁ replace in a cool,dry location when not in use. To prevent dust and dirt build-up, use the original packaging to repack the ﬁ replace.

TROUBLESHOOTING

If the ﬁ replace will not operate, check the following:

Check that the power cord is plugged into a 120 V AC electrical outlet. Do not use extension cords.
Check that the power indicator light on the control panel is illuminated to show that the ﬁ replace is getting power from the outlet.
Check if the battery in the remote control needs to be replaced.
Unplug the ﬁ replace, wait 15 minutes for the internal components to reset and then plug it back in.

LIMITED “CARRY IN” WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non- transferable.

TERMS OF WARRANTY
Plastic parts are warranted for thirty (30) days from the date of purchase, with no extensions provided.
First 18 months: During the ﬁ rst eighteen (18) months, any functional parts of this product found to be defective, will be repaired or replaced, at warranter’s option, at no charge to the original purchaser.

To obtain service: Contact the dealer where the unit was purchased, or contact the nearest authorized Danby service depot, where service must be performed by a qualiﬁ ed service technician. If service is performed on the unit by anyone other than an authorized service depot, all obligations of Danby under this warranty shall be void.
It is the responsibility of the purchaser to transport the appliance to the nearest authorized service depot. Transportation charges to and from the service location are not protected by this warranty and are the responsibility of the purchaser Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS
Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or implied, made or intended by Danby or its authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or statute is hereby expressly excluded. Save as herein provided, Danby shall not be responsible for any damages to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or property caused by the unit.

GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

Power failure.
Damage in transit or when moving the appliance.
Improper power supply such as low voltage, defective house wiring or inadequate fuses.
Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating conditions (i.e.. extremely high or low room temperature).
Use for commercial or industrial purposes (i.e.. If the appliance is not installed in a domestic residence).
Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, ﬂoods etc.
Service calls resulting in customer education.
Improper Installation (ie. Building-in of a free-standing appliance or using an appliance outdoors that is not approved for outdoor application, including but not limited to: garages, patios, porches or anywhere that is not properly insulated or climate controlled).

Proof of purchase date will be required for warranty claims; retain bills of sale. In the event that warranty service is required, present the proof of purchase to our authorized service depot.

Danby Products Ltd. Guelph, Ontario, Canada
Danby Products Inc. Findlay, Ohio, U.S.A.

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9 DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

Trademarks of Danby Products Limited and/or its subsidiaries

Printed in China