novostella NTF96-RGBCW Smart LED Flood Light User Guide
- June 8, 2024
- novostella
Table of Contents
NTF96-RGBCW Smart LED Flood Light User Guide
NTF96-RGBCW Smart LED Flood Light
THANK YOU for choosing Novostella. Before using this smart light, please take
a mintue to know how it works.
The smart light can work with both Amazon Alexa and Google Assistant. But the
light after being installed will need to be paired with an app called ‘Smart
Life’ first, and then the Smart Life app will need to be bound with either
Amazon Alexa or Google Assistant to activate the yoke control function.
Therefore, this user guide is consists of four parts. Part one and two are
fun-damental set-up, while part three and four are alternatives. If you use
Amazon Alexa for yoke control, please follow instructions on part one, two and
three. If you use Google Assistant for voice control, please skip part three,
follow the instructions on part one, two and four. Part five is for general
troubleshooting.
Part One – How to install the light ? 1- 5
Part One – How to install the light ?
Warning
- Please check If the light and the parts are Intact before installation.
- Make sure to cut off power before installation.
- Please do not place this light in corrosive conditions.
- If there Is any damage to the cord, please cut off the power and stop using it immediately.
- Please do not retrofit the light within the warranty period.
- To ensure the light works properly, please use the voltage indicated on the packing.
SKU | NTF96-RGBCW |
---|---|
Model Number | NTF96 |
Wattage | 20W |
Color | RGB, Warm White, Cool White |
Color Temperature | 2700K-6500K, RGB |
Frequency | 50/60Hz |
Waterproof Rating | IP66 |
Input Voltage | 120V±10% AC |
Beam Angle | 120° |
Working Temperature | -25°C-40°C |
Corn onents
Note: Cord – type Y attachment. For type Y attachment: If the external flexible cable or cord of this lumiilaiit is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
Dimension
Installation
StepA : According to the spacing of two screw bits on the bracket, drill
two holes on the mounting panel. Note: Maximum mounting height is over Sm.
Step B : Aim the bracket at the holes and fix it with two bolts. Step C:
Adjust the lighting direction up or down as per your need and plug in to power
the light on.
Note:
01 Make sure that the distance between the light and the object being lit is
more than 1 meter, so as to avoid high temperature caused by short distance.
The light source of this luminaire is not replaceable.
Limitation of Indoor and Outdoor Use
- This light is waterproof and dampproof. It is protected against the rain, but it cannot be immersed in water.
- The mounting position of this light should be able to bear at least 10 times as heavy as the light.
- This light should be used in condition that is good for heat dissipation. Its working temperature should be less than 45°C. Too high the working temperature will cause serious lumen depression and affect lifespan of the light.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instru-
ctions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interfer-ence that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>