reolink RLC-410W 4MP Dual-Band WiFi Security IP Camera User Guide

: June 8, 2024
: reolink

Table of Contents

What’s in the Box
Camera Introduction
Connection Diagram
Set up the Camera
Install the Camera
Troubleshooting
Speciﬁcations
Notiﬁcation of Compliance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RLC-410W
Quick Start Guide

What’s in the Box

reolink RLC 410W 4MP Dual Band WiFi Security IP Camera - FIGURE
1

NOTE: Camera and accessories vary with different camera models that you purchase.

Camera Introduction

reolink RLC 410W 4MP Dual Band WiFi Security IP Camera - FIGURE
2

Connection Diagram

Before initial setup, follow the steps below to connect your camera.

Connect the camera to a LAN port on your router with an Ethernet cable.
Power on the camera with a power adapter.

reolink RLC 410W 4MP Dual Band WiFi Security IP Camera - FIGURE
3

Set up the Camera

Download and Launch the Reolink App or Client software, and follow the onscreen instructions to ﬁnish initial setup.

On Smartphone
Scan to download the Reolink App. https://reolink.com/wp-json/reo-v2/app/download
On PC
Download path of the Reolink Client: Go to https://reolink.com>Support>App&Client.

Install the Camera

Installation Tips

Do not face the camera towards any light sources.
Do not point the camera towards a glass window. Or, it may result in poor image performance because of the window glare by infrared LEDs, ambient lights or status lights.
Do not place the camera in a shaded area and point it towards a well-lit area. Or, it may result in poor image performance. For better image quality, please make sure that the lighting condition for both the camera and the capture object is the same.
For better image quality, it’s recommended to clean the lens with a soft cloth from time to time.
Make sure the power ports are not exposed to water or moisture or blocked by dirt or other elements.
Do not install the camera at places where rain and snow may hit the lens directly.
The camera may work in extreme cold conditions as low as -25°C.
Because when it is powered on, the camera will produce heat. You may power on the camera indoors for a few minutes before installing it outdoors.

NOTE: There are two different types of mounts for bullet cameras. Please check out the mount included in the package and follow the corresponding instruction to install the camera properly.
Mount the Camera

reolink RLC 410W 4MP Dual Band WiFi Security IP Camera - FIGURE
4 | Drill holes in accordance with the mounting hole template.
NOTE: Use the drywall anchors included in the package if needed.
---|---
| Install the mount base with the mounting screws included in the package.
NOTE: Run the cable through the cable notch on the mount base.
reolink RLC 410W 4MP Dual Band WiFi Security IP Camera - FIGURE
6 | To get the best ﬁeld of view, loosen the adjustment knob on security mount and turn the camera.
| Stiffen the adjustment knob to lock the camera.

NOTE: If your camera has another mount without the adjusting knob, please loosen the adjusting screw with the provided hex key and turn the camera as shown below to adjust the angle.

reolink RLC 410W 4MP Dual Band WiFi Security IP Camera - FIGURE
8

Twist the screws with the wrench to unlock the camera and adjust its direction.

After adjustment, twist the screws back to lock the camera.

Troubleshooting

IP Camera Is Not Powering on
If you ﬁnd your camera is not powering on, try the following solutions:

Please check whether the outlet is working properly or not. Try to plug the camera into a different outlet and see if it works.
Please check whether the DC adapter is working or not. If you have another 12V DC power adapter which is working, please use another power adapter and see if it works.

If these won’t work, please contact Reolink Support https://support.reolink.com
**IR LEDs Stop Working**
If you ﬁnd the IR LEDs of your camera stop working, try the following solutions:

Go to Device Settings and check whether you have enabled Infrared LEDs. If the LEDs are disabled, please enable them.
Please go to Live View and check the Day/Night mode. Set the mode to Auto to activate the IR lights.
Upgrade your camera’s ﬁrmware to the latest version.
Restore the camera to the factory settings and check the IR light settings again.

If these won’t work, please contact Reolink Support https://support.reolink.com

Speciﬁcations

Hardware Features
IR Distance: 30 meters (100ft)
Day/Night Mode: Auto switchover
General
Operating Temperature: -10°C to 55°C (14°F to 131°F)
Operating Humidity: 10%-90%
Weather Resistance: IP66 certiﬁed weatherproof

Notiﬁcation of Compliance

FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC RF Exposure Warning Statements
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.
Simpliﬁed EU Declaration of Conformity
Reolink declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
Correct Disposal of This Product
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.
Limited Warranty
This product comes with a 2-year limited warranty that is valid only if purchased from Reolink official stores or Reolink authorized resellers. Learn more: https://reolink.com/warranty-and-return/.
NOTE: We hope that you enjoy the new purchase. But if you are not satisﬁed with the product and plan to return, we strongly suggest that you reset the camera to factory default settings and take out the inserted SD card before returning.
Terms and Privacy
Use of the product is subject to your agreement to the Terms of Service and Privacy Policy at reolink.com. Keep out of the reach of children. End User License Agreement By using the Product Software that is embedded on the Reolink product, you agree to the terms of this End User License Agreement (“EULA”) between you and Reolink. Learn more: https://reolink.com/eula/.
ISED Statements
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

Radio Frequency Exposure Statement for IC
The device has been evaluated to meet general RF exposure requirements. The device can be used in mobile exposure conditions. The min separation distance is 20cm.
Operation of this device is restricted to indoor use only. (5180-5240MHz)
Technical Support
If you need any technical help, please visit our official support site and contact our support team before returning the products, https://support.reolink.com
This radio transmitter [IC: 26839-2201D] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Antennas

Antenna Type	Manufacturer	Model/Part No.	Gain (dBi)
omnidirectional antenna	Shenzhen Yingjiachuang
Electronic Technology Co.. Ltd	YJC-60302-W27	2.89	2400-2500
omnidirectional antenna	Shenzhen Yingjiachuang
Electronic Technology Co.. Ltd	YJC-60302-W27	2.55	5150-5850