QNAP QSW-M2106 Series Layer 2 Web Managed Switch Installation Guide
- June 8, 2024
- QNAP
Table of Contents
QNAP QSW-M2106 Series Layer 2 Web Managed Switch
Package Contents
Top Panel
Power Input
Hardware Installation
Accessing the Web User Interface
If the device is unable to connect to a DHCP server to obtain an IP address,
you can access the web user interface by changing the IP address of the
computer to 169.254.100.102.
Note: Ensure that you change the IP address of the computer to its
previous setting after configuring the switch.
The default IP address of the QSW-M2106 series is 169.254.100.101.
Logging into the Web User Interface
Default username: admin
Default password: The default password is the MAC address in uppercase
letters without special characters. For example, if the first MAC address is
00-08-9B-F6-15-75, then the admin password will be 00089BF61575.
Hardware Components
Front Panel Ports
- Status LED
- 1 x RJ45 console port
- 6 x 2.5GbE RJ45 ports
- 4 x 10GbE SFP+ ports
- 4 x 10GbE SFP+/RJ45 combo ports
- Reset button
LED Behavior
| LED | Status | Description |
|---|---|---|
| System Status | Green | The device is ready. |
| Flashes green | • The device is being initialized. |
• The firmware is being updated.
Note: When updating the firmware, do not remove the power cord or USB cable, and do not force-exit the application.
• The device is being reset.
Red| A fatal device error occurred.
Off| The device is powered off.
2.5GbE RJ45 (Left)| Green| The link speed is operating at 2.5 Gbps.
Flashes green| Data is being transmitted.
Off| There is no network connection.
2.5GbE RJ45 (Right)
| Amber| The link speed is operating at 1 Gbps, 100 Mbps or 10 Mbps.
Flashes amber| Data is being transmitted.
Off| There is no network connection.
10GbE SFP+ (left)| Green| The link speed is operating at 10 Gbps.
Flashes green| Data is being transmitted.
Off| There is no network connection.
10GbE SFP+ (right)| Amber| The link speed is operating at 1 Gbps.
Flashes amber| Data is being transmitted.
Off| There is no network connection.
10GbE SFP+/RJ45 combo (RJ45, left)| Green| The link
speed is operating at 10 Gbps.
Flashes green| Data is being transmitted.
Off| There is no network connection.
10GbE SFP+/RJ45 combo (RJ45, right)| Amber| The link
speed is operating at 5 Gbps, 2.5 Gbps, 1 Gbps, or 100 Mbps.
Flashes amber| Data is being transmitted.
Off| There is no network connection.
10GbE SFP+/RJ45 combo (SFP+, left)| Green| The link
speed is operating at 10 Gbps.
Flashes green| Data is being transmitted.
Off| There is no network connection.
10GbE SFP+/RJ45
combo (SFP+, right)
| Amber| The link speed is operating at 1 Gbps.
Flashes amber| Data is being transmitted.
Off| There is no network connection.
Specifications
| Model | QSW-M2106-4S | QSW-M2106-4C |
|---|---|---|
| Dimensions (H x W x D) | 42.5 x 290 x 127 mm | |
| Net weight Input voltage range Switching capacity RJ45 ports | 1.12 | |
| KG | 1.12 KG |
100 ‒ 240VAC
80 Gbps
8
SFP+ ports| 2| N/A
Combo ports (SFP+/RJ45)| N/A| 2
Operating temperature| 0˚C to 40°C (32°F to 104°F)
Relative humidity| 5% to 95% (non-condensing)
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Class B(QSW-M2106-4S) and Class B(QSW-M2106-4C) Notice:
This equipment has been tested and found to comply with the limits for a Class
B(QSW-M2106-4S) and Class B(QSW-M2106-4C) digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference,
in which case the user will be required to correct the interference at his own
expense.
Modifications: Any modifications made to this device that are not approved
by QNAP Systems, Inc. may void the authority granted to the user by the FCC to
operate this equipment.
This device complies with CE compliance, QSW-M2106-4C Class B, QSW-M2106-4S
Class B.
According to the requirement of the WEEE legislation the following user
information is provided to customers for all branded QNAP Electronics products
subject to the WEEE directive.
This symbol on the product or on its packaging indicates that this product
must not be disposed of with your other household waste. Instead, it is your
responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and
electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and
ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, your household
waste disposal service or the shop where you purchased the product.
Office in EU; QNAP GmbH,
Karl-Arnold-Straße 26, 47877 Willich, Germany
Office in UK;
QNAP Ltd,
2 Drakes Meadow, Swindon SN3 3LL United Kingdom
This device complies with the UKCA requirements for products sold in Great Britain.
THIS PRODUCT CONTAINS A BUTTON BATTERY
If swallowed, a lithium button battery can cause severe or fatal injuries
within 2 hours. Keep batteries out of reach of children. If you think
batteries may have been swallowed or placed inside any part of the body, seek
immediate medical attention.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>